1. Product Overview
The XINJE TouchWin TG765 Series is a 7-inch TFT HMI touch screen designed for general industrial control applications. It features a high-resolution display, a powerful RISC processor, and various communication ports to ensure reliable and efficient operation.

Package Contents
Upon receiving your HMI, please verify that the package contains the following items:
- XINJE TouchWin TG765 Series HMI Unit
- Mounting hardware (clips/screws)
- Power connector
- USB cable (may vary by model)
- Documentation (this manual or similar)

2. Setup and Installation
2.1 Mounting the HMI
The HMI is designed for panel mounting. Ensure adequate space for ventilation and cable connections. Use the provided mounting clips to secure the unit into a cutout of appropriate dimensions on your control panel.

2.2 Power Connection
Connect the HMI to a stable DC 24V power supply. The power input terminal is typically a green screw-type connector on the rear of the unit. Ensure correct polarity (+ and -) to prevent damage.
- Power Requirement: DC 24V, 4W (typical)
2.3 Communication Port Connections
The TG765 series HMIs offer various communication options. Refer to the specific model for available ports.
- COM0: Supports PLC RS232 / PLC RS485 (2-wire/4-wire)
- COM1: Supports PLC RS232 / PLC RS485 (2-wire/4-wire)
- COM2: Supports PC / PLC connection
- USB Host: For expandable memory or data transfer.
- Ethernet Port: (Available on TG765-ET models) For network communication.



2.4 DIP Switch Settings
Some models feature DIP switches on the rear panel for configuring communication protocols or other settings. Consult your project's specific requirements and the programming software documentation for correct DIP switch configurations.
3. Operation
3.1 Powering On/Off
- Power On: After connecting the power supply, the HMI will automatically power on. The 'PWR' indicator light (usually on the front panel) will illuminate.
- Power Off: Disconnect the DC 24V power supply. Ensure any critical operations are completed and data is saved before powering off.
3.2 Touch Screen Interaction
The HMI features a resistive touch screen. Use a finger or a stylus to interact with the displayed interface. Calibration may be required during initial setup or if touch accuracy degrades.
3.3 Project Download and Data Transfer
Project files are typically created using the TouchWin programming software on a PC. These projects can be downloaded to the HMI via USB or Ethernet (for ET models). The USB Host port can also be used for connecting external storage devices for data logging or recipe management.
4. Maintenance
4.1 Cleaning
To clean the HMI screen and casing, use a soft, damp cloth. Avoid abrasive cleaners, solvents, or excessive moisture, which can damage the display or internal components.
4.2 Environmental Considerations
Ensure the HMI operates within its specified environmental conditions (temperature, humidity) to prolong its lifespan. Avoid direct sunlight, excessive dust, and corrosive environments.
4.3 Firmware Updates
Periodically check the manufacturer's website for firmware updates. Follow the provided instructions carefully when performing updates to avoid damaging the unit.
5. Troubleshooting
- No Power: Check the DC 24V power supply connection and ensure correct polarity. Verify the power source is active.
- Screen Unresponsive: Perform a touch screen calibration. If the issue persists, restart the HMI.
- Communication Errors: Verify cable connections, DIP switch settings, and communication parameters in the HMI project and connected PLC/device.
- Display Issues: If the screen is blank or distorted, check power connections. If the issue persists, contact technical support.
6. Specifications
| Feature | Specification |
|---|---|
| Brand Name | TECNR |
| Model Numbers | TG765-MT, TG765-UT, TG765-ET, TG765-XT-C, TG765S-MT, TG765S-XT, TG765S-UT |
| Application | General |
| Display | 7" TFT |
| Resolution | 800*480 |
| Processor | 32-bit 800MHz RISC |
| Memory | 128M FLASH + 64M DDR2 |
| Expandable Memory | 1 USB Host |
| Recipe Memory RTC | 512KB + RTC |
| COM Ports | COM0:PLC RS232/PLC RS485-2/4, COM1:PLC RS232/PLC RS485-2/4, COM2:PC/PL |
| Certification | CE |
| Origin | Mainland China |
| Package Weight | 1.1 kg |
| Package Dimensions | 32cm x 20cm x 10cm |
7. User Tips
- The TG765 series features a thinner design compared to previous versions while retaining the same core functionalities, making it suitable for installations where space is a concern.
- Always ensure the product matches the images and specifications provided to confirm you have the correct model for your application.
8. Warranty and Support
For warranty information, technical support, or service inquiries, please contact your vendor or the manufacturer directly. Keep your purchase records handy for any support requests.