CXG D60W D90W D110W

Contents

CXG Electric Soldering Iron Ceramic Heating Element User Manual

Models: D60W, D90W, D110W Series

Brand: CXG

1. Product Information

Product Overview

This manual provides instructions for the CXG Soldering Iron Ceramics Heating Element Heater, designed for use with CXG D60W, D90W, and D110W electric soldering irons. These plug-in heating cores are essential components for maintaining optimal performance of your soldering station.

Key Features:

  • Original CXG heating element
  • Ceramics Heating Element technology
  • Plug-in Heating core design for easy replacement

What's in the Box:

  • 1 x Plug-in Heating core

2. Safety & Warnings

Warning:

  • Turn off the power when finished using or leaving the room to prevent fire.
  • When the power is on, the soldering iron tip will reach a temperature of 100℃~400℃ (212°F~752°F). Take precautions against burns.
  • Never immerse the soldering iron in water or use it with wet hands to prevent electric shock.
  • The soldering iron control end consists of precision components; avoid dropping it.
  • When not in use, place the handle on the metal stand. Do not place it near wooden boards, paper, or flammable materials to prevent fire.
  • Keep out of reach of children.

3. Specifications

AttributeValue
Model NumbersD60W, D90W, D110W
Compatible Heating ModelsA1316D, A1326D, A1319D, A1329D, A13111D, A13211D
Dimensions65mm (length)
Input Voltage90V-110V, 220V-240V (depending on model)
Output Voltage60W, 90W, 100W (depending on model)
Output Temperature80-500 °C
Temperature Stability+/- 2 °C
FunctionOriginal CXG heating element
Function 2Ceramics Heating Element
Function 3Plug-in Heating core
CertificationNONE
OriginMainland China

Note: The specific voltage and wattage depend on the model variant (e.g., A1316D for D60W 110V, A1326D for D60W 220V, etc.).

Diagram showing the dimensions of the heating element: 3.8mm diameter, 65mm length, 12mm pin length.

Image: Dimensions of the CXG Ceramic Heating Element.

4. Setup Instructions (Heating Element Replacement)

This section outlines the general procedure for replacing the ceramic heating element in compatible CXG soldering irons. Always ensure the soldering iron is unplugged and completely cooled before attempting any replacement.

  1. Preparation: Ensure the soldering iron is disconnected from the power supply and has cooled down to room temperature.
  2. Access the Heating Element: Carefully disassemble the soldering iron handle to expose the existing heating element. This usually involves unscrewing the tip and a retaining collar.
  3. Remove Old Element: Gently pull out the old heating element from its socket. Note the orientation of the pins if applicable.
  4. Insert New Element: Align the pins of the new CXG ceramic heating element with the corresponding holes in the soldering iron's internal connector. Push it firmly but gently into place. Refer to the diagram below for pin configuration (pins 1-2 for heating, 3-4 for temperature sensor).
  5. Reassemble: Reassemble the soldering iron handle, ensuring all parts are securely fastened.
  6. Test: Plug in the soldering iron and turn it on to verify proper heating and temperature control.

Video: Demonstration of the CXG ceramic heating element, showing its physical appearance and connection pins.

CXG ceramic heating element with four pins, labeled 1, 2, 3, 4, and a diagram showing pins 1-2 for heating and 3-4 for temperature sensor.

Image: CXG Ceramic Heating Element with pinout diagram. Pins 1 and 2 are for the heating element, while pins 3 and 4 are for the temperature sensor.

5. Operating Instructions

Once the ceramic heating element is correctly installed in your CXG soldering iron, ensure the soldering iron is placed on its dedicated stand. Connect the power supply to the soldering station. Turn on the power and allow the iron to reach the desired operating temperature. Always refer to your specific soldering iron's manual for detailed temperature control and usage instructions.

6. Maintenance & Storage

Maintenance:

  • After soldering, return the handle to the dedicated holder and ensure the soldering iron tip has completely cooled before storing.

Storage:

  • Avoid leaving the soldering iron in a high-temperature, dry-heat state for extended periods.
  • Store the heating element in a cool, dry place, away from direct sunlight and moisture.

7. Troubleshooting

If your soldering iron is not heating up or maintaining temperature after replacing the heating element, consider the following:

  • Incorrect Installation: Double-check that the heating element is fully seated and its pins are correctly aligned within the soldering iron's connector.
  • Incompatible Model: Ensure the heating element model (e.g., A1316D, A1326D) matches your specific CXG soldering iron model and voltage requirements.
  • Power Supply Issue: Verify that the soldering station is receiving power and that its power switch is on.
  • Damaged Element: Although new, inspect the heating element for any visible damage or bent pins before installation.
  • Soldering Station Malfunction: If the issue persists, the problem might lie with the soldering station itself rather than the heating element. Consult the soldering station's manual or a qualified technician.

8. User Tips

No specific user tips were available from reviews or Q&A for this product at this time. Always follow the manufacturer's instructions for best results and safety.

9. Manufacturer & EU Representative Information

Manufacturer:

  • Name: Shenzhen Hua xin Electronic Trading Co., Ltd.
  • Province: Guangdong
  • City: Shenzhen
  • Address: 6B, Building 6, Longbi Industrial Zone, Bantian Street, Longgang District

EU Authorized Representative:

  • Name: eVatmaster Consulting GmbH
  • Address: Bettingastr 3060325 Frankfurt am Main Germany
  • Phone number: +49-6995179070
  • Email: contact@evatmaster.com

10. Compliance Information

This product complies with relevant European safety standards, indicated by the CE mark. It is also designed with ESD (Electrostatic Discharge) safety in mind.

CE ESD SAFE

Made in China

11. Support

For further detailed information and diagrams, a comprehensive user manual in PDF format is available. You can access it directly via the following link:

View User Manual (PDF)

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.