AnyTone AT-5555N II

Contents

ANYTONE AT-5555N II CB Radio User Manual

Model: AT-5555N II

1. Introduction

The AnyTone AT-5555N II is a 10-meter amateur radio mobile transceiver designed for reliable communication. This manual provides detailed instructions for its setup, operation, and maintenance to ensure optimal performance and user satisfaction.

Functions & Features

  • Large LCD display with backlight dimming
  • FM / AM / USB / LSB / CW / PA modes
  • Frequency Tuning Steps: 100Hz / 1KHz / 5KHz / 10KHz / 100KHz / 1MHz
  • ±500Hz/5KHz CLARIFIER Adjustment (R/T/R+T selectable)
  • Flexible Menu Functions and PC Programming Software
  • TX and RX Noise Reduction
  • VFO / BAND / Memory Channel modes
  • CTCSS/DCS with RX/TX Split functions
  • Enhanced VOX Functions (can support digital mode operation)
  • SQ, ASQ Function (FM and AM mode only)
  • RF GAIN Adjustment
  • RF PWR Adjustment
  • SCAN Function
  • NB/ANL Function
  • Repeater Shift / Offset Frequency Function
  • SIG / PWR / SWR Meter Functions
  • TOT Function
  • HI-CUT Function
  • SWR Protection
  • Power Supply Voltage Protection
  • WX weather channels with RX VFO mode (136-174MHz FM)
  • Weather Alert
  • Key-Lock Function
  • Model Name Customization Function
  • Compatible with electret and dynamic MIC types
  • ECHO Function
  • Programmable RB Function
  • Keypad BEEP Function
  • +10KHZ Function
  • DW Dual-Watch Function
  • EMG Channel Function

2. Setup

Standard Accessories

The product package includes the following items:

Line drawing of included accessories: Radio, Microphone, Install bracket, Screws, Pads, Adjusting screws, Microphone Hanger, Non-slip mat, Fuse (15A 250V)

Figure 2.1: Included accessories for the AT-5555N II CB Radio.

  • Radio Unit
  • Microphone
  • Installation Bracket
  • Screws
  • Pads
  • Adjusting Screws
  • Microphone Hanger
  • Non-slip Mat
  • Fuse (15A 250V)
  • Operating Instructions Manual (this document)

Installation

Choose the most appropriate location for installation, considering both simplicity and practicality. If installing in a vehicle, ensure the radio does not obstruct the driver or passengers.

  1. Use the Self-tapping Screws and Pads to fix the Bracket to a suitable location.
  2. Attach the Adhesive Case Protectors to the inside ends of the Mounting Bracket and insert the Radio. Fit the Adjusting Screws loosely, and choose a suitable angle by moving the Adjusting Screws to one of the 3 positions on the Mounting Bracket.
  3. Tighten the Adjusting Screws firmly by hand. Make sure the radio and all accessories are securely mounted.

Microphone Connection

The microphone connects to the front panel of the radio.

  1. Insert the microphone connector (RJ45) into the microphone jack on the front panel.
  2. The microphone connector will "click" into place, indicating a secure connection.

Video 2.1: Demonstration of connecting the microphone to the radio.

Close-up of the front panel showing the RJ45 microphone port and the microphone cable being plugged in.

Figure 2.2: RJ45 pluggable microphone connection.

Antenna Installation

Before using this radio, install an efficient and resonant antenna. A correctly installed and tuned antenna is crucial for excellent communication performance. This radio requires an antenna impedance of 50 ohms, unbalanced.

  1. Screw the antenna connector into the antenna jack on the rear panel.
  2. Ground the antenna system to ensure best performance of this radio.

WARNING:

  • NEVER transmit without a connected resonant antenna, or a suitable 50 ohm load being connected. Damage to the radio may result.
  • To reduce the risk of electric shock, or radio damage, base station installations should include lightning protection devices.
  • Consult your AnyTone dealer for available antenna options.

A mobile antenna can be mounted in various locations, for example:

Diagram showing various mobile antenna mounting locations on a car: roof, trunk, and fender.

Figure 2.3: Examples of mobile antenna mounting locations.

Power Connection

This radio requires a 13.8V (12V) DC power supply. Do not connect the radio directly to a 24V DC battery system. Refer to the radio Specifications to ensure your 13.8V DC power supply can provide enough current (amps) for optimal performance.

  1. Connect the positive (red) power cable to the + terminal of the battery.
  2. Connect the negative (black) power cable to the - terminal of the battery.
  3. Connect the DC power cable to the transceiver's power supply connector on the rear panel.
Close-up of the rear panel showing the power input, antenna connector, data port, and external speaker port.

Figure 2.4: Rear panel connections including power input.

  • Locate the power cable away from high temperature, moisture, and other electrical systems. Ensure it is installed where it cannot be damaged.
  • It is not recommended to use a vehicle cigar/cigarette lighter socket to power the radio, as it may not supply the correct voltage or current.
  • Do not remove the fuse holder from the cable.

Replacing Fuses

This radio requires a 15A, 250V fuse. If the fuse blows, determine the reason and correct the problem before replacing it.

  1. Twist the two fuse covers in opposite directions to open the in-line fuse holder.
  2. Replace the blown fuse with a new one and close the fuse holder.
  3. Be sure to only use the correct fuse type (15A 250V); otherwise, damage may occur.

Install Microphone Hanger

Choose a location that will not interfere with the driver. Use the supplied self-tapping screws and pads to install the hanger.

Install External Speaker (Optional)

If using an external speaker, choose an 8 ohm speaker with a 3.5mm mono (double cable) TS type plug.

  1. Install the external speaker in a suitable place.
  2. Plug the speaker into the EXT.SP jack on the rear panel of the radio.

3. Operating Instructions

Getting Acquainted with the Radio

Familiarize yourself with the front panel controls, rear panel connections, and LCD display indicators.

Front Panel

Front panel diagram of the AT-5555N II radio with numbered keys and their functions listed in a table.

Figure 3.1: Front Panel Layout and Key Functions.

No.KeyFunctions
1FRQSwitch between channel mode and frequency mode / Offset setup
2BANDSwitch band: A-L-VFO / ECHO setup
3MENUMenu Function key
4MODESwitch mode (FM / AM / USB / LSB / CW / PA) / TSQ setup
5DWDual-watch scan / Frequency +10K function
6RBRB function / Beep prompt function
7NBNB function / HI-CUT function
8SCANScan / Scan add / Scan delete
9MEMUse, store or delete memory channels
10EMGEmergency Channel / Keypad lock.
11PWRRF Power Control
12RFGRF Gain Control
13SQSquelch Control
14CLARSSB/CW Clarifier Control
15VOLPower On/Off; Volume Control
16CHChannel Switch, CH Push key
17-Microphone Jack
18-LCD Display

Rear Panel

The rear panel houses the main connections for antenna, power, and external accessories.

Close-up of the rear panel showing the power input, antenna connector, data port, and external speaker port.

Figure 3.2: Rear Panel Connections.

No.Functions
19External SP Jack
20External PA Jack
21Antenna Jack
22Power Supply Jack
23Programming Jack

LCD Display Indicators

The LCD display provides visual feedback on the radio's status and settings.

No.IndicatorDescription
1SIGRX Signal strength indicator.
2PWRTX Signal strength indicator.
3SWRSWR indicator.
4Model NameModel name indicator (can be customized with PC Software).
5Key LockAppears when the Keypad lock function is ON.
6FUNCAppears when MENU key is short-pressed.
7EMGAppears when using Emergency channel.
8FIN RTAppears when SSB/CW clarifier is enabled.
9AQAppears when using ASQ.
10SCAppears when Scan function is ON.
11Modulation ModeDisplays the modulation mode.
12CTCAppears when CTCSS is enabled.
13BPAppears when Beep is ON.
14DWAppears when Dual-watch function is ON.
15RBAppears when RB function is ON.
16NBAppears when Noise Blanker is ON.
17•Appears when the channel is excluded from the Scan List.
18HICAppears when Hi-Cut function is ON.
19REPAppears when repeater function is ON.
20IOkAppears when the +10KHz function is ON.
21ECHOAppears when Echo function is ON.
22Band IndicatorWorking band indicator.
23Frequency/ChannelDisplay of frequency and channel.
24DCSAppears when DCS is enabled.
25NRAppears when Noise Reduction function is ON.
26VOXAppears when VOX function is ON.

Basic Operation

Power OFF/ON

  1. Turn the VOL knob clockwise to switch the radio ON. The radio may emit a beep (if the BEEP Prompt function is enabled). The LCD display will show a frequency or a channel number.
  2. Turn the VOL knob anti-clockwise to switch off the radio.

Volume Control

When the radio is turned on, turning the VOL knob clockwise increases the Volume level. Turning it anti-clockwise reduces the Volume level. Adjust the volume during communication to a suitable level.

Note: On-screen display of the level can be enabled/disabled with PC software.

RF Power Control

Valid for AM/FM/LSB/USB/CW modes. Turn the PWR control to adjust the TX Output Power. Turn the control clockwise to increase Power, and anti-clockwise to reduce Power.

Note: On-screen display of the level can be enabled/disabled with PC software.

RF Gain Control

When the radio is receiving, turn the RFG control to adjust the RF Gain. Turn the control clockwise to increase RF Gain, and anti-clockwise to reduce RF Gain.

Note: On-screen display of the level can be enabled/disabled with PC software.

SQUELCH Control

When the radio is receiving, turn the SQ control clockwise to adjust the Squelch level.

Note: On-screen display of the level can be enabled/disabled with PC software.

SSB Clarifier Control

When the radio is transmitting or receiving, turn the CLAR inner shaft to adjust USB/LSB/CW TX or RX frequency. Turn it clockwise to increase frequency, anti-clockwise to reduce frequency.

Note: See Menu items #14 and #15 for CLAR settings.

Channel Selection

When the radio is in Channel Mode, turn the channel knob to select the desired channel. Turn clockwise to increase the channel number, and anti-clockwise to reduce the channel number.

Note: In Channel display mode, pressing the CH [PUSH] key will increase the change rate by 10 times the channel step size (for faster channel stepping).

Keypad Functions

Frequency Control

  1. In Frequency Mode, press CH (PUSH) key to adjust the VFO at different frequency steps.
  2. When the desired VFO frequency digit is flashing, turn CH clockwise to increase frequency, and turn anti-clockwise to reduce frequency.
  3. After a few seconds of no key-presses, the VFO frequency digit will stop flashing, and the radio will return to the STEP setting selected in Menu Item #8 "STEP".

MENU+MODE

  • Press [MENU] and then press [MODE] to enter WX Weather Channel mode.
  • Press and hold [FRQ] to enter WXVFO mode (136-174MHz FM Receiver).

FRQ/REP

  • Short press [FRQ] to switch between Frequency display mode and Channel display mode.

Offset Direction Function

  1. Long press [FRQ] for 2 seconds to enter the Offset direction function, LCD displays "REP".
  2. Press CH (PUSH) to select offset, turn channel switch to select.
    • REPOF: Turn OFF offset direction function.
    • REP+: Turn ON + offset direction function, TX frequency>RX frequency.
    • REP-: Turn ON - offset direction function, RX frequency>TX frequency.
  3. Press CH (PUSH) to store and exit.

BAND/TONE

Band Selection Function

  • Short press [BAND] to choose band A-B-C-D-E-F-G-H-I-J-K-L-VFO.

Echo Function

  1. Long press [BAND] for 2 seconds to enter the ECHO function, LCD displays "ECHO".
  2. Long press [BAND] for 2 seconds to turn off the ECHO function.

MENU

  • Long press [MENU] for 2 seconds to enter the Menu list.

MODE/TSQ

Modulation Mode

  • Short press [MODE] to choose mode FM-AM-USB-LSB-CW-PA.

Note: Modes can be enabled and disabled using the PC software.

CTCSS/DCS (TSQ) Function

  • Long press [MODE] for 2 seconds to enter CTCSS/DCS setting.
  • Press CH (PUSH) to turn on or off the CTCSS/DCS function.
  • When CTCSS/DCS is turned on, the LCD displays CTC or DCS.

DW/+10K

Dual-Watch function

  1. Short press [DW] to turn on Dual Watch, LCD displays "DW".
  2. Short press [DW] again or press PTT to exit DW mode.

Frequency+10KHz function

  1. Long press [DW] for 2 seconds to turn on the frequency +10KHz function, LCD displays "10K".
  2. Long press [DW] for 2 seconds again to turn off the frequency +10KHz function.

RB/BEEP

RB function

  1. Short press [RB] to turn on RB function, LCD displays "RB".
  2. Press CH (PUSH) to select RB frequency, turn the CH channel switch to select. OFF~5.
    • OFF: Turn off RB function.
  3. Press CH (PUSH) to store and exit.

BEEP Prompt function

  1. Long press [RB] for 2 seconds to enter BEEP Prompt function, LCD displays "BP".
  2. Long press [RB] for 2 seconds again to turn off BEEP Prompt function.

NB/HCUT

NB (Noise Blanker) function

  1. Short press [NB] to enable the NB function, LCD displays "NB".
  2. Short press [NB] again to turn off the NB function.

HI-CUT function

  1. Long press [NB] for 2 seconds to enable HI-CUT function, LCD displays "HIC".
  2. Long press [NB] for 2 seconds again to turn off the HI-CUT function.

SCAN/SKP

Scan Function

  1. Short press [SCAN] to enter the Scan function, LCD displays "SC".
  2. In Scan mode, turning the CH switch will change the Scan direction.
  3. Short press [SCAN] again to exit.

Add/delete scan list function

  1. Long press [SCAN] for 2 seconds to add or delete the current channel from the scan list.
  2. When LCD displays "•", the current channel is excluded from the Scan list; When the LCD does not display "•", the current channel is added to Scan list.

MEM/STOR

Using Memory Channel mode:

  1. Short press [MEM] to enter Memory Channel mode, turn the CH channel switch to choose memory channel. M1-M99, (total of 99 Memory Channels).
  2. Short press [MEM] again to exit Memory Channel mode.

Store/Delete Memory Channels:

  1. Store Memory Channel: When the radio is not in Memory Channel mode, choose the frequency to be stored, and then hold [MEM] to enter storage mode, the channel number flashes. Turn the CH switch to choose the location to be stored (M1-M99), then hold [MEM] until the channel number stops flashing. The memory is stored.
  2. Delete Memory Channel: While in Memory Channel mode, hold [MEM] for over 2 seconds, the Memory Channel number flashes. Turn the CH switch to choose the memory to be deleted, then hold [MEM] until the channel number stops flashing. Then memory is deleted.

EMG/LOCK

Choose EMG Channel:

  • Short press [EMG] to use Emergency channel mode, LCD displays "EMG".
  • Short press [EMG] once to choose CH9.
  • Short press [EMG] again to choose CH19.
  • Short press [EMG] again to return to the last used normal channel.

Note: See Menu item #20 and #21 for EMG channel settings.

Keypad Lock Function:

  1. Long press [EMG] to lock keys, LCD displays "".
  2. Long press [EMG] again to unlock the keys.

Note: When the Keypad Lock function is turned on, only the PTT and FRQ button is valid.

Background Function Menu Operation

The radio features a comprehensive menu system for advanced settings. To access and navigate the menu:

  1. Press [MENU] for 2 seconds to enter the Menu list.
  2. Turn the CH Channel switch to select the required Menu item.
  3. Press CH (PUSH) to enter the Menu item setup.
  4. Turn the CH Channel switch to select the wanted setting.
  5. Press any other key or wait 5 seconds; the setting will be stored.

For a complete list of menu items and their functions, please refer to the detailed tables in the official User Manual (PDF) available at: AnyTone AT-5555N II User Manual (PDF).

4. Maintenance

Regular maintenance ensures the longevity and optimal performance of your AT-5555N II CB Radio.

General Care

  • Keep the radio clean and free from dust and moisture. Use a soft, dry cloth for cleaning.
  • Avoid exposing the radio to extreme temperatures, direct sunlight for prolonged periods, or harsh chemicals.
  • Ensure all connections (antenna, power, microphone) are secure and free from corrosion.

Fuse Replacement

As detailed in the Setup section, if the radio ceases to function due to a blown fuse, replace it with a 15A, 250V fuse after identifying and resolving the cause of the blow.

5. Troubleshooting

This section addresses common issues you might encounter with your AT-5555N II CB Radio.

Frequency Range Limitation (Below 28MHz)

Some users may find that the radio's frequency does not extend below 28MHz out of the box. This can often be resolved through a simple modification:

  • Modification for Extended Frequency Range (25-30MHz): To enable the full frequency range (e.g., 25-30MHz), you may need to perform a modification. This typically involves opening the radio, removing the cover with the speaker, and soldering or desoldering a specific contact, often labeled OR1 or similar, located in the lower right corner closer to the panel. Refer to specialized forums or resources like 'radioodditty' for detailed instructions and diagrams for your specific model.

WARNING: Performing internal modifications may void your warranty and should only be attempted by experienced individuals. Incorrect modifications can damage the radio.

VOX Function Behavior

The VOX function (Voice Operated Transmit) on this radio may only activate when the squelch is open. Ensure your squelch settings are appropriate for VOX operation.

General Issues

  • No Power: Check power cable connections, vehicle battery voltage, and the 15A fuse.
  • No Transmit/Receive: Ensure antenna is properly connected and tuned. Check SWR. Verify correct frequency and mode settings.
  • Poor Audio Quality: Check microphone connection. Adjust RF Gain and Squelch controls.

6. Specifications

General Specifications

ParameterValue
Frequency Range28.000-29.700MHz (Programmable)
Frequency BandsA/B/C/D/E/F/G/H/I/J/K/L + VFO
Channels40 default channels in each band (a total of 60 programmable channels per band)
Frequency ControlPhase-Locked-Loop Synthesizer
Frequency Step100Hz, 1KHz, 5KHz,10KHz,100KHz,1MHz
Frequency Tolerance±5.00ppm
Frequency Stability0.001%
Temperature Range-20°C to +50℃
MicrophoneWith push-to-talk, UP/DN and coiled cord
Input Voltage13.8V
Dimensions (in mm)250(L)x280(W)x60(H)
Weight1.5kg
Antenna ConnectorUHF, SO239

Transmitter Specifications

ParameterValue
Power OutputAM PEP: 60W / FM: 50W / SSB: 60W(PEP)
Current Drain10A maximum (with modulation)
ModulationAM/FM/USB/LSB/CW
Inter-modulation DistortionSSB: 3rd order, more than -25dB; 5th order, more than -35dB
SSB Carrier Suppression55dB
Unwanted Sideband50dB
Frequency ResponseAM/FM: 300 to 3000Hz SSB: 450 to 2500Hz
Output Impedance50 ohms, unbalanced

Receiver Specifications

ParameterValue
SensitivitySSB: 0.25μV for 10dB(S+N)/N at greater than 1/2-watt of audio output
AM:1.0µV for 10dB(S+N)/N at greater than 1/2watt of audio output
FM: 1.0µV for 20 dB (S+N)/N at greater than 1/2 watt of audio output
Adjacent-Channel SelectivityAM/FM: 60dB SSB: 70dB
Image RejectionMore than 65dB
IF FrequencyAM/FM: 10.695MHz 1st IF, 455KHz 2nd IF
SSB: 10.695MHz
RF Gain Control45dB adjustable for optimum signal reception
Automatic Gain Control (AGC)Less than 10dB change in audio output for inputs from 10 to 100,000 microvolt.
SquelchAdjustable; threshold less than 1.0µV.
Automatic Squelch Control (only AM/FM) 1.0μV
Audio Output Power3 watts into 8 ohms
Frequency ResponseAM/FM: 300 to 3000Hz SSB: 300 to 3000Hz
Built-in Speaker8 ohms, round.
External Speaker (Not Supplied)8 ohms; disables internal speaker when connected.

WX Channels

ChannelFrequency
WX-01162.550MHz
WX-02162.400MHz
WX-03162.475MHz
WX-04162.425MHz
WX-05162.450MHz
WX-06162.500MHz
WX-07162.525MHz

Note: 40 RX channels (VHF FM mode) can be programmed between 136-174MHz.

CTCSS/DCS Chart

The radio supports both Analog (CTCSS) and Digital (DCS) squelch codes. For a complete list of supported codes, please refer to the official User Manual (PDF) available at: AnyTone AT-5555N II User Manual (PDF).

7. Warranty & Support

Warranty Information

A 12-month warranty is offered for the machine itself, and a 6-month warranty is provided for accessories. This warranty covers defects in materials and workmanship under normal use.

Important:

  • We test every unit before shipping. If a defect is still present upon arrival, please contact us within 3 days of parcel receipt for a replacement.
  • If the item is defective within 30 days of receipt, we will bear one-way shipping fee for warranty.
  • If defective after 30 days of receipt, buyers will be responsible for all extra shipping fees.

EU Declaration of Conformity

The AT-5555N II 10m Amateur Radio conforms to the essential requirements of the Radio Equipment Directive 2014/53/EU. For detailed compliance information, refer to the EU Declaration of Conformity in the official User Manual (PDF).

ATTENTION: Conditions of Use!

The band of frequencies on which this device operates is administered by limitations and/or permissions for their usage. Consequently, in EU countries, operators must consult the entrusted authorities. In particular, they must possess a license or a frequency assigned to them by their respective competent authority.

Contact & Support

For further assistance, technical support, or warranty claims, please contact Qixiang Electron Science & Technology Co.,Ltd. via their official website: www.anytone.net.

8. User Tips

Here are some helpful tips from other users to enhance your experience with the AT-5555N II CB Radio:

  • Programming Software: If the provided software link doesn't work, users have reported success finding compatible software (e.g., for the QT-60 Pro) on community sites like 'radioodditty'. This can be useful for customizing settings and expanding functionality.
  • Frequency Expansion: For users needing to operate outside the default 28.000-29.700MHz range, a hardware modification might be necessary to unlock frequencies from 25MHz to 30MHz. This often involves a simple soldering task on a specific contact (e.g., J802 jumper or OR1) inside the radio. Always proceed with caution and consult detailed guides if attempting this.
  • VOX Function: Be aware that the VOX function might only work when the squelch is open. Adjust your squelch settings accordingly if you intend to use VOX.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.