1. Introduction
1.1 General Applications
The GEYA GYM9+RD miniature circuit breaker with remote control is designed for a wide range of electrical applications. It can be used in:
- Power grid terminal lines, such as meter boxes.
- New energy circuit management, including PV solar control boxes.
- Smart electricity and smart home systems.
- New energy vehicle charging piles.
1.2 Function Features
This device offers advanced features for enhanced safety and convenience:
- Can be matched with a circuit breaker or leakage protection switch.
- Automatically recloses when the MCB/RCCB/RCBO trips unexpectedly, eliminating the need for manual closing and reducing maintenance costs.
- Timely eliminates faults to improve efficiency.
- Features 3 reclosing attempts; continuous closing failure within 15 minutes triggers an alarm via auxiliary contact.
- Equipped with a manual/automatic selector switch.
- Includes mechanical/electronic double locking function.
- The shaft transmission mode ensures more stable and reliable operation.
- Compatible with other accessories.
- Work status is indicated by an LED.
- Complies with IEC/EN60898-1 standards.
- Bilateral busbar wiring capabilities for wider use.
- Maximum connecting ability of 25mm², with a wiring torque of 3N*m, suitable for various installing equipment.
1.3 Product Overview
The GEYA GYM9+RD is a miniature circuit breaker with remote control and automatic reclose functionality. It is primarily used for protection against overload and short circuit in AC 50Hz/60Hz systems, with rated voltages of 230V/400V and rated currents from 6A to 63A. It can also be used for non-frequent on-and-off switching operations under normal circumstances.

2. Specifications
2.1 Model and Connotation
The model designation GRD9L-R indicates the following:
- GRD9L Series: Base product series.
- R: Auto Reclosing + AUX (Auxiliary contact).
- Rated control supply voltage: D12 (DC12V), D48 (DC24~48V), A220 (AC220V).
When ordering, the matching MCB/RCCB/RCBO specification and model should be indicated. For example: GRD9L-R + GYM9 2P C40 or GRD9L-R + GYL9 2P 40A 30M.
2.2 Technical Parameters
| Technical parameters | GRD9L-R |
|---|---|
| Control mode | Auto Reclosing |
| Supply terminals | A1-A2 |
| Voltage range | DC12V, DC24V-48V |
| Supply voltage tolerance | -10%; +10% |
| Power input | DC max.1W(standby) max.20W(action) |
| Voltage range | AC 220V (50-60Hz) |
| Supply voltage tolerance | -10%; +10% |
| Power input | AC max.1VA(standby) max.20VA(action) |
| Supply indication | red LED |
| Action time | ≤1s |
| Auto reclosing times | 3 |
| Auto reclosing interval time | 10s-60s-300s |
| Reset the closing times | No trip or manual reset within 15 minutes after successful closing |
| Mechanical life | 10000 |
| Electrical life | Refer to MCB / RCCB / RCBO catalogue |
| Operating temperature | -20°C to +55°C (-4°F to 131°F) |
| Storage temperature | -35°C to +75°C (-22°F to 158°F) |
| Mounting/DIN rail | Din rail EN/IEC 60715 |
| Protection degree | IP20 |
| Operating position | any |
| Overvoltage category | III. |
| Pollution degree | 2 |
| Max. cable size (mm²) | solid wire max.1×2.5 or 2×1.5 / with sleeve max.1×2.5 (AWG 12) |
| Dimensions | 82×18×78mm |
| Weight | 80g |
2.3 Dimensions

3. Installation
3.1 Cooperating with RCCB/MCB
The auto reclose device is designed to integrate seamlessly with Residual Current Circuit Breakers (RCCB) or Miniature Circuit Breakers (MCB).


3.2 Accessories Installation
Additional accessories can be installed to enhance functionality.

3.3 Closing Lock
The device features a closing lock mechanism for safety during circuit checks.

Note: When checking the circuit, the RCCB/MCB cannot close when the lock function is activated.
4. Operation
4.1 Mode Selection
The device features a selector switch for different operational modes:
- AUTO mode: The auto reclosing function is enabled.
- MANU mode: The auto reclosing function is disabled. In this mode, the MCB/RCCB/RCBO can only be opened and closed manually.
4.2 Power-On Behavior
Upon power-on, the green indicator will flash for 2 seconds to allow the power supply to stabilize. After stabilization, the green indicator light will remain on. If the MCB/RCCB/RCBO fails to trip, the red indicator light will be on. During the auto reclosing delay, the red indicator will flash. After the delay, the device will automatically switch on, and the green light will be on.
5. Wiring Diagrams
5.1 GRD9M-C, GRD9M-S, GRD9M-R Wiring

5.2 Application Example

6. Functions Diagram

Note: If the closing times and delay time need to be customized, please contact GEYA company.
7. Troubleshooting
Refer to the table below for common faults and their resolutions:
| Fault description | Resolvent |
|---|---|
| Unable to close or open. |
|
| Trip immediately after closing. |
|
8. User Tips
- The product is generally well-finished and detailed, suggesting good quality.
- Ensure the power supply voltage is normal before operation to prevent issues.
- Always verify the working mode (AUTO/MANU) is correctly set according to your needs.
- If the device trips immediately after closing, thoroughly check for overload, short circuit, or leakage faults in the connected circuit.
- The device supports a wide range of rated currents from 6A to 63A and operates at 50/60Hz.
- Some models may require an external power input (12V or 220V) for re-initialization or specific control modes.
9. Warranty and Support
For any technical assistance, warranty claims, or further support, please contact GEYA customer service. For detailed item guides and documents, please refer to the official user manual PDF available from the seller.
10. Safety and Disposal
10.1 Safety Precautions
Caution: The products must be installed by qualified electricians. All and any electrical connections of the time relay shall comply with the appropriate safety standards.
10.2 Disposal of Electrical Waste
All electrical waste should be disposed of in compliance with current WEEE regulations to protect the environment.