1. Product Overview
The diymore DM-W3001 is a versatile microcomputer temperature controller designed for precise temperature measurement, display, and control. It supports both heating and cooling modes, making it suitable for a wide range of applications, from industrial control to home automation and specialized equipment like seafood machines. The controller features an LED digital display for clear temperature readings and simple button-based operation for setting temperature parameters.
2. Specifications
| Feature | Specification |
|---|---|
| Model | DM-W3001 |
| Type | Microcomputer Temperature Controller Module |
| Measurement/Control Range | -50°C to 110°C |
| Measuring Accuracy | ±0.1°C |
| Control Precision | ±0.1°C |
| Measurement Input | NTC 10K waterproof probe (1 meter length) |
| Output Type | Direct Output |
| Supply Voltage Options | DC 12V, DC 24V, AC 220V (Isolation 220V option available) |
| Max Power Output (Voltage Dependent) | 12V: 120W, 24V: 240W, 220V: 1500W |
| Max Current | 10A |
| Operating Temperature Range | -50°C to 110°C |
3. Setup and Wiring
WARNING: Connect the output correctly before powering on. Ensure all connections are secure and appropriate for the selected voltage and load. Incorrect wiring can damage the device or connected equipment.
Refer to the diagram on the back of the controller (Figure 2) for wiring connections. The terminals are labeled as follows:
- NTC: Connect the NTC temperature probe here.
- OUT: These terminals are for connecting your heating or cooling device (load).
- IN: These terminals are for the power supply input (DC 12V, DC 24V, or AC 220V, depending on your model).
Ensure the power supply matches the voltage version of your DM-W3001 controller (e.g., 12V controller with 12V power supply). The maximum power output for the connected load should not exceed the specified wattage for your controller's voltage (120W for 12V, 240W for 24V, 1500W for 220V).
4. Operating Instructions
The DM-W3001 controller has two buttons: an 'Up' button (▲) and a 'Down' button (▼).
4.1. Setting Start Temperature
- Display Start Temperature: Briefly press the 'Up' (▲) button. The display will show the current start temperature setting.
- Set Start Temperature: Long press the 'Up' (▲) button until the temperature display starts flashing. Use the 'Up' (▲) or 'Down' (▼) buttons to adjust the desired start temperature value. Once set, wait a few seconds for the display to stop flashing and save the setting automatically.
4.2. Setting Stop Temperature
- Display Stop Temperature: Briefly press the 'Down' (▼) button. The display will show the current stop temperature setting.
- Set Stop Temperature: Long press the 'Down' (▼) button until the temperature display starts flashing. Use the 'Up' (▲) or 'Down' (▼) buttons to adjust the desired stop temperature value. Once set, wait a few seconds for the display to stop flashing and save the setting automatically.
4.3. Heating and Cooling Modes
- Heating Mode: If the Start Temperature (▲) is set to be less than the Stop Temperature (▼), the controller operates in heating mode. The output will activate when the temperature drops below the Start Temperature and deactivate when it reaches the Stop Temperature.
- Cooling Mode: If the Start Temperature (▲) is set to be greater than the Stop Temperature (▼), the controller operates in cooling mode. The output will activate when the temperature rises above the Start Temperature and deactivate when it reaches the Stop Temperature.
5. Maintenance
To ensure the longevity and accurate operation of your DM-W3001 temperature controller, follow these maintenance guidelines:
- Keep the device clean and free from dust and debris. Use a soft, dry cloth for cleaning.
- Avoid exposing the controller to extreme temperatures, high humidity, or corrosive environments.
- Regularly check wiring connections for tightness and signs of wear or corrosion.
- Ensure the NTC probe is clean and properly immersed in the medium whose temperature is being measured.
6. Troubleshooting
If you encounter issues with your DM-W3001 controller, consider the following troubleshooting steps:
- No Power/Display: Check the power supply connection and ensure it matches the controller's voltage requirements. Verify the power source is active.
- Incorrect Temperature Reading: Ensure the NTC probe is correctly connected to the 'NTC' terminals. Check the probe for any physical damage.
- Output Not Activating: Verify that the load device is correctly wired to the 'OUT' terminals and is functioning independently. Check your set start and stop temperatures to ensure they are configured for the desired heating or cooling action. Ensure the load's power consumption does not exceed the controller's maximum rating.
- Display Flashing Continuously: This usually indicates you are in a setting mode. Wait for a few seconds for the setting to save, or briefly press both 'Up' and 'Down' buttons simultaneously to exit the setting mode if it persists.
7. User Tips
- Always double-check your wiring before applying power to prevent damage to the controller or connected devices.
- For critical applications, consider using an external fuse or circuit breaker for the power input and load output to protect against overcurrent.
- When setting temperatures, allow for a small hysteresis (difference between start and stop temperatures) to prevent rapid cycling of your heating/cooling device, which can extend its lifespan.
8. Warranty and Support
For warranty information, technical support, or further assistance, please contact the seller or manufacturer directly. Keep your purchase receipt or order details handy when seeking support.
A detailed user manual in PDF format may also be available for download from the seller's website or via the following link: DM-W3001 User Manual (PDF).