BRIGHTWIN XH300

Contents

BRIGHTWIN XH300 Auto Signal Generator User Manual

Model: XH300

1. Introduction

The BRIGHTWIN XH300 is a third-generation auto signal generator designed for simulating various vehicle sensor signals. It is an essential tool for automotive maintenance and repair, allowing technicians to simulate Hall sensor signals, magnetoelectric sensor signals, crankshaft position sensor signals, camshaft signals (4+1 and 6+1), engine speed signals, vehicle speed (odometer) signals, and magnetoelectric ABS sensor signals.

The device supports both 12V and 24V systems, making it suitable for a wide range of vehicles including cars, trucks, motorcycles, and construction machinery. It features an LED display for clear readings, adjustable frequency from 1Hz to 8000Hz, and adjustable signal amplitude (5V and 12V).

XH300 Auto Signal Generator overview with signal types and applications

Figure 1: XH300 Auto Signal Generator Overview

XH300 Auto Signal Generator features and supported signals

Figure 2: XH300 Key Features

2. Package Contents

Please check the package for the following items:

  • 1 x XH300 Auto Signal Generator (Host)
  • 2 x Plugs
  • 2 x Alligator Clip Cables
  • 1 x Power Cord
  • 1 x User Manual (Printed Copy)
XH300 Packing list

Figure 3: XH300 Packing List

3. Setup

3.1 Power Supply

The XH300 requires an external DC 12-24V power supply to operate. Ensure the power supply is within this range and connected correctly to the 'Power in DC12-24V' terminal on the device.

3.2 Device Layout and Controls

Familiarize yourself with the device's controls and indicators:

  • Display Screen: Shows the signal frequency (Hz) by default.
  • SET Key: Tap to select signal type. Press and hold to enter CKP signal editing mode.
  • Up/Down Buttons: Adjust signal frequency or values in editing mode.
  • Phase Reversal (H/L) Button: Reverses the signal phase by 180 degrees.
  • Hall/Magnetoelectric Indicators: LEDs indicating the active signal output type.
  • Power In (DC12-24V): Power input terminal.
  • Signal Amplitude (12V/5V): Selects the output signal amplitude.
  • Hall Signal Output: Terminal for Hall signals.
  • Magnetoelectric Output: Terminal for Magnetoelectric signals.
XH300 controls and signal types

Figure 4: XH300 Control Panel and Terminals

3.3 Wiring Diagrams

Connect the XH300 to the vehicle's ECU or sensor system according to the specific signal you wish to simulate. Below are common wiring configurations:

Crankshaft Position Sensor Simulation

The crankshaft position sensor can be Hall type or magnetoelectric type. Connect the XH300 output to the ECU's signal input (SIG/SIG1/SIG2) and ground (GND).

Wiring diagram for Hall and Magnetoelectric crankshaft position sensors

Figure 5: Crankshaft Position Sensor Wiring

Magnetoelectric ABS Sensor Signal Simulation

For magnetoelectric ABS sensor simulation, connect the XH300 output to the ECU. Note that the XH300 does not support two-wire Hall type ABS sensors.

Wiring diagram for Magnetoelectric ABS sensor

Figure 6: Magnetoelectric ABS Sensor Wiring

ECU Testing (Engine Fuel Injector & Ignition Coil)

The XH300 can be used to test ECUs by simulating signals for engine fuel injectors and ignition coils. Connect the XH300 output to the ECU's signal input. Note that crankshaft and camshaft synchronization signals are not supported for this specific test setup.

Wiring diagram for testing ECU with engine fuel injector and ignition coil

Figure 7: ECU Test Wiring (Injectors/Ignition)

Engine Speed Signal Simulation

To simulate engine speed signals to an ECU or other control unit, connect the XH300 output as shown in the diagram.

Wiring diagram for engine speed signal to ECU and other control unit

Figure 8: Engine Speed Signal Wiring

4. Operating Instructions

4.1 General Operation

  1. Connect the XH300 to a DC 12-24V power source.
  2. Connect the appropriate output terminals of the XH300 to the vehicle's ECU or sensor system according to the desired simulation.
  3. The display screen will show the signal frequency in Hz by default.

4.2 Signal Type Selection

Short press the SET key to cycle through the available signal types. The XH300 has six built-in crankshaft signals and two camshaft signals:

  • Crankshaft Signals: 58+2, 34+2, 36+2, 60+0 (Standard), 56+4, 10+1
  • Camshaft Signals: 4+1, 6+1

The 60+0 signal is a standard tooth signal and can simulate speed signals and magnetoelectric ABS signals.

4.3 Frequency Adjustment

Once a signal type is selected, use the Up and Down buttons to adjust the signal frequency within the range of 1Hz to 8000Hz. This effectively adjusts the simulated speed.

4.4 Signal Amplitude Adjustment

The XH300 offers adjustable signal amplitude of 5V and 12V. Select the appropriate amplitude based on the requirements of the system being tested.

4.5 Crankshaft Signal Editing (Missing Tooth Signal)

The XH300 allows users to edit custom crankshaft signals, specifically missing tooth patterns. The newly edited signal is automatically saved after the 56+4 signal and overwrites the original 10+1 signal.

  1. Long press the SET key: The two digits on the left of the display will blink. Use the Up or Down key to modify the number of teeth (range: 1-99).
  2. Short press the SET key: The right digit will flash. Use the Up or Down key to modify the number of missing teeth (range: 1-9).
  3. Short press the SET key again: Exit the editing mode. The signal editing is complete.

4.6 Signal Phase Reversal

Press the H/L (phase reversal) button to reverse the signal phase by 180 degrees. The display will indicate 'H' for high phase waveform and 'L' for low phase waveform.

Waveform outputs for Hall, Magnetoelectric, Crankshaft, and Camshaft signals

Figure 9: Example Waveform Outputs

4.7 Video Demonstration

Watch this video for a demonstration of vehicle speed signal simulation, engine speed signal simulation, and ECU testing:

Video 1: XH300 Signal Simulation and ECU Testing

5. Maintenance

To ensure the longevity and optimal performance of your XH300 Auto Signal Generator:

  • Keep the device clean and free from dust and debris. Use a soft, dry cloth for cleaning.
  • Avoid exposing the device to extreme temperatures, humidity, or direct sunlight.
  • Store the device in a safe place when not in use, preferably in its original packaging or a protective case.
  • Do not attempt to disassemble or repair the device yourself. Refer to qualified technicians for any service needs.

6. Troubleshooting

If you encounter issues with your XH300, consider the following:

  • No Power: Ensure the DC 12-24V power supply is correctly connected and functioning.
  • Incorrect Signal Output: Verify that the correct signal type is selected using the SET key and that the frequency and amplitude settings are appropriate for your application.
  • Signal Not Detected by ECU: Double-check all wiring connections for proper polarity and secure contact. Ensure the XH300 is compatible with the specific sensor type (e.g., it supports magnetoelectric and three-wire Hall, but not two-wire Hall).
  • Crankshaft/Camshaft Synchronization: The XH300 is primarily a signal generator for individual sensor signals and does not support complex crankshaft and camshaft synchronization signals for direct engine operation simulation. It acts as a time base for the ECU/ECM.
  • Output Current Limitations: For certain applications requiring higher current output (e.g., some Mercedes Benz PLD-MR systems), the generator's 50mA output might need external amplification if the target system requires 200mA.

Important: This product is special equipment for automobile maintenance. Non-professional personnel should use it under the guidance of auto repair technicians.

7. Specifications

Feature Specification
Product Name Auto Signal Generator
Model Number XH300
Power Supply DC 12-24V
Output Signal Type Hall, Magnetoelectric
Frequency Range 1-8000Hz
Signal Amplitude 5V, 12V (Adjustable)
Signal Editing Number of teeth 1-99, Missing teeth 1-9
Signal Phase Adjustable (Reversible)
Display LED display (3.0 - 4.9 Inches)
Certifications CE, RoHS
Dimensions (L x W x H) 110mm x 80mm x 27mm
Weight 0.3 kg
XH300 Product dimensions

Figure 10: XH300 Exterior Dimensions

8. User Tips

  • The XH300 has been successfully tested with various ECUs, including BMW, for simulating RPM Hall signals.
  • It can simulate crankshaft sensor signals for motorcycles and is generally compatible with diesel engines (e.g., Isuzu, Toyota) by simulating the engine's phonic wheel signal.
  • The device is well-regarded for its build quality and functionality.
  • If you need to simulate a specific crankshaft signal not pre-programmed, utilize the editing function to create custom missing tooth patterns.

9. Warranty and Support

For detailed warranty information and technical support, please refer to the official BRIGHTWIN website or contact your seller.

An electronic version of the user manual (PDF) may be available for download from the manufacturer's website: BRIGHTWIN XH300 User Manual (PDF)

Official Website: www.brightwintech.com

© 2024 BRIGHTWIN. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.