TYT TH-9800Plus

Contents

TYT TH-9800Plus Quad Band Transceiver User Manual

Model: TH-9800Plus

Introduction

Thank you for choosing the TYT TH-9800Plus Quad Band Mobile Transceiver. This device offers reliable, clear, and efficient communication services with an ergonomic design and intuitive controls. Designed for durability, the TH-9800Plus is suitable for various environments and communication needs across HF/VHF/UHF bands.

For a comprehensive understanding of its features, functions, and maintenance, please read this manual thoroughly.

TYT TH-9800Plus Quad Band Transceiver
Figure 1: TYT TH-9800Plus Quad Band Transceiver with microphone.

User Safety Information

  • Do not attempt to configure your transceiver while driving.
  • This transceiver is designed for a 13.8V DC power supply. Do not use a 24V battery.
  • Keep the transceiver away from interferential devices (e.g., TVs, generators).
  • Do not expose the transceiver to long periods of direct sunlight or place it close to heating appliances.
  • If an abnormal odor or smoke is detected, turn off the power immediately and contact your dealer.
  • Do not transmit with high power for extended periods, as the transceiver may overheat.

Package Contents

The standard package includes the following items:

  • Radio unit x 1
  • Keypad DTMF microphone x 1
  • Radio body mounting bracket x 1
  • DC power cable with fuse holder x 1
  • Front controller separation cable x 1
  • Front controller mounting bracket x 1
  • Screw packs x 1
  • Protection fuses x 1
  • User manual x 1
Standard package contents of TYT TH-9800Plus
Figure 2: Standard package contents including the radio unit, microphone, mounting brackets, and cables.

Main Features

  • Quad band transmit and receiver (29/50/144/430 MHz)
  • Wide receiving range: 26-33 MHz, 47-54 MHz, 108-180 MHz, 320-512 MHz, 750-950 MHz
  • AM Air-band reception capability
  • Independent controls for each left and right band
  • V+V, U+U, V+U simultaneous receive capability
  • Built-in V+U cross-band repeater and full duplex capability
  • 809 memory channels with independent settings per channel
  • 50W high power output for VHF band and 40W for UHF band
  • Standard 50 groups of CTCSS tone and 104 groups of DCS code
  • User-defined CTCSS tone & DCS code capability
  • DTMF / 2-Tone / 5-Tone for selective calling
  • Voice compander and encryption scramble
  • Automatic Repeater Shift (ARS)
  • Detachable front controller and remote mounting capability
  • Ultra-size LCD dual display screen
  • User-programmable microphone keys
  • FM Radio 108-135.995MHz
  • High/Low Output Power Levels
  • Reverse Frequency Selection
  • Dual (V/U) Squelch Set Levels
  • Dual Repeater Offsets Select-Able
  • Multi Scanning
  • Repeater Offset
  • Keypad Lock Function
  • Channel Name Editing
  • CTCSS/DCS Encode/Decode

Setup

Initial Installation

Select a safe and convenient location for installation, minimizing danger while operating. Ensure the unit is in a well-ventilated area, shielded from direct sunlight.

Mounting Bracket Installation

  1. Drill 4 holes where the mounting bracket is to be installed.
  2. Insert the supplied screws, nuts, and washers through the mounting bracket and tighten.
  3. Adjust the angle for your suitable position.
Adjustable mounting bracket for TYT TH-9800Plus
Figure 3: Adjustable mounting bracket allowing up to 25 degrees adjustment for comfortable operation.

Separation Cable Connection (Remote Control)

The TH-9800Plus can be installed with the main body hidden (e.g., under a seat) and the front panel separated. A 4.5m (14.8 ft) separation cable is supplied for this purpose.

Connect the controller and the main unit using the separation cable.

Remote control setup diagram showing main body and separated front panel
Figure 4: Remote control setup, illustrating how the main body can be hidden and the front panel used separately with a 4.5m separation cable.

Video 1: Demonstration of connecting the microphone to the radio unit.

DC Power Cable Connection

The transceiver requires a 12V DC power supply. Route the supplied DC power cable directly to the vehicle's battery terminals, ensuring the shortest path. Avoid using cigarette lighter sockets due to potential voltage drops. Isolate the cable from heat, moisture, and ignition system cables.

  1. Route the DC power cable directly to the vehicle's battery terminals.
  2. After installing the cable, use heat-resistant tape to secure it with the fuse box.
  3. Confirm correct polarity: Red to positive (+), Black to negative (-).
  4. Reconnect any wiring removed from the negative terminal.
  5. Connect the DC power cable to the transceiver's power supply connector, ensuring it clicks firmly into place.

Fixed Station Operation

For fixed station use, a separate 13.8V DC power supply (not included) with a recommended current capacity of 12A is required.

  1. Connect the DC power cable to the regulated DC power supply, ensuring correct polarities (Red: positive; Black: Negative).
  2. Connect the transceiver's DC power connector to the DC power cable, ensuring it clicks firmly into place.

Note: Before connecting power, ensure both the transceiver and power supply are OFF. Do not plug the power supply into an AC outlet until all connections are made.

Replacing Fuses

If a fuse blows, identify and correct the cause before replacing it. If new fuses continue to blow, disconnect power and contact your dealer.

Fuse LocationFuse Current Rating
Transceiver15A
Supplied Accessory DC power cable20A

Note: Only use fuses of the specified type and rating. Using incorrect fuses can damage the transceiver. Prolonged use with a low vehicle battery or engine off can discharge the battery.

Antenna Connection

Install an efficient, well-tuned 50Ω impedance antenna. Use a low-loss coaxial feed-line with a characteristic impedance of 50Ω to match the transceiver's input impedance. Transmitting without an antenna or matched load can damage the transceiver. Fixed stations should use a lightning arrester.

Accessories Connections

External Speaker

If using an external speaker, choose one with an impedance of 8Ω. The external speaker jack accepts a 3.5mm mono (2-conductor) plug.

Note: The external speaker output uses a double port BTL. Ensure the speaker is not connected to ground, as this can cause a fault.

Microphone

Connect the microphone with an 8-pin modular plug into the modular socket on the side of the main unit. Press firmly until the locking tab clicks. Attach the supplied microphone hanger in an appropriate location.

Ergonomic microphone with PTT and DTMF keypad
Figure 5: Ergonomic microphone with DTMF keypad for comfortable operation.
Back side details of TYT TH-9800Plus
Figure 6: Rear panel connectors including active cooling fan, antenna, mini USB data, and external speaker ports.

Operating Instructions

Front Panel Operation

The front panel features various controls for easy operation:

  • LEFT DIAL: Tuning dial for the left band, main band selection, rapid tuning (1 MHz steps), and band toggling (144 MHz -> 350 MHz -> 430 MHz -> 850 MHz -> 29 MHz -> 50 MHz).
  • LEFT VOL/SQL: Outer VOL adjusts left receiver audio level. Inner SQL adjusts left receiver background noise. Short press for single receive mode on/off. Press and hold for 1/2 second to lock/unlock front panel keys.
  • LEFT [LOW] (Key Mode 2): Short press to switch power output level (LOW-MID2-MID1-HIGH) for the left band. Press and hold for 1/2 second to switch memory display mode.
  • LEFT [V/M]: Short press to switch frequency control for the left band between VFO and Memory mode. Press and hold for 1/2 second for "Memory Tuning".
  • LEFT [HM]: Short press to recall a favorite "HOME" frequency memory. Press and hold for 1/2 second to activate Priority Channel Scanning.
  • LEFT [SCN]: Short press to activate the Scanner on the left band. Press and hold for 1/2 second to set up Scan Skip List or Preferential Scan List.
  • [SET]: Short press to enter Menu mode. Press and hold for 1/2 second to transfer Main band VFO contents to Memory system.
  • RIGHT [LOW] (Default): Short press to switch power output level for the right band. Press and hold for 1/2 second to switch memory display mode.
  • RIGHT [MHz] (Key Mode 2): Short press to allow tuning in 1 MHz steps on the Main band VFO. Press and hold for 1/2 second to allow tuning in 10 MHz steps.
  • RIGHT [RPT]: Short press to change frequency shift direction (RPT -, RPT +, RPT OFF). Press and hold for 1/2 second to reverse TX and RX frequencies during split-frequency operation.
  • RIGHT [V/M] (Default): Short press to switch frequency control for the right band between VFO and Memory mode. Press and hold for 1/2 second for "Memory Tuning".

Rear Panel and Microphone Functions

The rear panel and microphone have specific functions:

No.PortFunction
1ANTConnection for 50Ω antenna.
2EXT SPTerminal for optional external speaker.
3DATAPC programming data port.
No.PortFunction
1PTTPress to transmit.
2DWNDecrease channel number or setting value.
3UPIncrease channel number or setting value.
4MICSpeak here during transmission.
5LOCKLocks out the microphone buttons except 0-9 and PTT.
6LAMPIlluminates the microphone keypad.
7Number KeyInput channel number or DTMF dial out etc.
8Programmable Keys (P1-P4)User-defined functions. Default: P1: switch Main band, P2: switch VFO/Memory mode, P3: select CTCSS/DCS mode, P4: select TX power output level.

Basic Operation

Switching Power On/Off

To turn ON, press and hold the RIGHT VOL/SQL knob for 1/2 second. To turn OFF, press and hold the RIGHT VOL/SQL knob for 1/2 second again.

Adjusting Volume

Turn the outer VOL control clockwise to increase, counter-clockwise to decrease receiver audio level. Volume levels are set independently for LEFT and RIGHT VOL controls.

Adjusting Squelch Level

Turn the inner SQL control clockwise to increase, counter-clockwise to decrease receiver background noise. Squelch levels are set independently for LEFT and RIGHT SQL controls.

Selecting the Operating Band

In "Dual Receive" mode, the "Main" band (for transmission) is indicated by the "MAIN" icon. Short press the microphone's [P1] key or the DIAL knob to switch "Main" bands between left and right. The "CAN" icon will light up on alternative sides of the display.

Note: Short press the LEFT VOL/SQL knob to switch single receive mode ON/OFF. When ON, the working voltage is shown on the "sub" band, and "KEY2" icon appears.

Selecting Frequency Band

Press and hold the LEFT DIAL knob for 1/2 second to toggle the operating band on the left side (144 MHz -> 350 MHz -> 430 MHz -> 850 MHz -> 29 MHz -> 50 MHz...). Press and hold the RIGHT DIAL knob for 1/2 second to toggle the operating band between 144 MHz and 430 MHz on the right side.

Selecting Desired Frequency

1. Tuning Dial: In VFO mode, rotate the DIAL knob to tune in pre-programmed steps. Clockwise increases frequency, counter-clockwise decreases. For rapid 1 MHz steps, short press the DIAL knob then rotate.

2. Direct Frequency Entry by Microphone Keypad: Use the DTMF microphone keypad to directly enter the Main band operating frequency. For frequencies below 100 MHz, enter leading zeros (e.g., 029025 for 29.025 MHz).

Receiving

The "BUSY" sign will appear whenever receiving a call on the channel you are on. If the squelch level is set too high, the signal may not be received.

Transmitting

Hold the microphone 2.5-5cm from your mouth, press the PTT switch, and speak in your normal voice. The LED lights ORANGE and power intensity on the display indicate transmission is in progress.

Selecting Power Output Level

Press the [LOW] key to select one of four power settings: LOW (5W), MID 2 (10W), MID 1 (20W), HIGH (50W / UHF: 40W). Power levels are stored in memory registers. The Bar Graph on the display shows the selected power output.

Memory Operation

The TH-9800Plus offers 4 types of memory systems:

  • 800 standard memory channels (001-800)
  • 5 pairs of band-edge memories (L1/U1 through L5/U5)
  • 6 Home channels (one for each operating band)
  • 6 "Hyper-Memory" channels (A-F keys)

Memory Channel Storage

  1. Select desired frequency, CTCSS, DCS, repeater offset, and power level in VFO mode on the "Main" band.
  2. Press and hold [SET] for 1/2 second. A blinking memory number appears.
  3. Use the "Main" band DIAL knob or microphone's [UP]/[DWN] buttons to select the desired memory channel.
  4. Press and hold [SET] for 1/2 second again to add an alpha-numeric tag. Rotate the "Main" band DIAL to select characters (0-9, A-Z, /, *, +, -). Short press DIAL or [UP] to move to the next character. [DWN] moves back. Up to six characters can be used.
  5. Short press [SET] to save the tag and exit.

Note: To skip alpha-numeric tagging, short press [SET] directly after step 3.

Storing Independent Transmit Frequencies ("Odd Splits")

  1. Store the receiving frequency.
  2. Tune to the desired transmit frequency on the "Main" band, then press and hold [SET] for 1/2 second.
  3. Select the same memory channel number as in step 1.
  4. Press and hold PTT, then short press [SET] to save. The "+" icon will appear.

Memory Recall

In VFO mode, short press [V/M] to enter Memory mode. Rotate the DIAL knob or use the microphone's keypad to select the desired channel.

Note: Memory channels with frequencies on 29 MHz and 50 MHz cannot be recalled on the right band.

Memory Tuning

  1. Select the desired memory channel under MR (Memory Recall) mode.
  2. Press and hold [V/M] for 1/2 second; "MT" icon appears.
  3. Rotate the DIAL knob to tune to a new frequency.
  4. Short press [V/M] again to exit Memory Tuning; "MT" icon disappears.

Deleting Memories

  1. Short press [V/M] to enter Memory mode.
  2. Press and hold [SET] for 1/2 second, then rotate the "Main" band DIAL to select the memory channel (channel #1 cannot be deleted).
  3. Short press the "Main" band [SCN] key to delete the selected channel.

HOME Channel Memory

The TH-9800Plus allows quick recall of a favorite operating frequency on each band (HOME channel).

  1. Select desired frequency, CTCSS, DCS, repeater offset, and power level in VFO mode on the "Main" band.
  2. Press and hold [SET] for 1/2 second.
  3. Short press the "Main" band [HM] key to store the VFO frequencies.
  4. To recall, just press the [H/M] key in VFO or MR mode.

Hyper Memory Channel

Stores the total current configuration of the radio (frequency, CTCSS/DCS, repeater shift, power level, scanning, menu settings) for both left and right bands.

  1. Set up the desired configuration for both bands.
  2. Press and hold one of the Hyper Memory keys ([A] ~ [F]) for 2 seconds to store.
  3. Press the appropriate Hyper Memory Key [A] - [F] to recall.

Memory Only Mode

This mode disables VFO operation, allowing only memory channel selection. Useful for simplified operation.

  1. Turn the radio off.
  2. Press and hold LEFT [V/M] while turning the radio on.
  3. Rotate the DIAL knob to select (F-5 M-ONLY MODE), then short press [SET] to confirm. The radio restarts in Memory Only Mode.
  4. To return to normal, repeat the steps.

Advanced Features

Repeater Operation (Automatic Repeater Shift - ARS)

ARS automatically applies the appropriate repeater shift when tuning into designed repeater sub-bands.

  1. Enter Menu mode ([SET]).
  2. Select Menu #2 (ARS).
  3. Change setting to "ON" and short press [SET] to save.

To manually set repeater shift direction (if ARS is disabled or for different regions):

  1. Enter Menu mode ([SET]).
  2. Select Menu #24 (RPT.MOD).
  3. Select desired shift among "+", "-" and "OFF". Short press [SET] to save.

CTCSS Tone / DCS Code Operation

CTCSS setup involves setting the Tone Mode (Menu #31 TONE M) and Tone Frequency (Menu #30 TONE F).

  1. Enter Menu mode ([SET]).
  2. Select Menu #31 (TONE M).
  3. Select "ENC" (CTCSS Encoder) or "ENC.DEC" (CTCSS Encoder & Decoder). Short press [SET].
  4. Select Menu #30 (TONE F).
  5. Enable adjustment and select desired CTCSS tone frequency (e.g., 67.0 Hz to 254.1 Hz). Short press [SET] to save.

DCS setup involves setting the Tone Mode to DCS (Menu #31 TONE M) and then selecting a code (Menu #7 DCS.COD).

  1. Enter Menu mode ([SET]).
  2. Select Menu #31 (TONE M).
  3. Select "DCS" (Digital Code Squelch Encoder & Decoder). Short press [SET].
  4. Select Menu #7 (DCS.COD).
  5. Enable adjustment and select desired DCS code (000-777). Short press [SET] to save.

Note: DCS is an Encoder/Decoder system; receiver remains muted until a matching DCS code is received.

DCS Code Inversion

If the receiver squelch does not open with a common DCS code, try inverting the code.

  1. Enter Menu mode ([SET]).
  2. Select Menu #8 (DCS.N/R).
  3. Select mode: TRX N (Normal), RX R (RX Inverted), TX R (TX Inverted), or TRX R (Both Inverted). Short press [SET] to save.

Tone Search Scanning

Scans for CTCSS or DCS tones on incoming signals in VFO or Memory mode.

  1. Set radio for CTCSS or DCS decoder operation.
  2. Enter Menu mode ([SET]).
  3. Select Menu #30 (TONE F) for CTCSS or Menu #7 (DCS.COD) for DCS.
  4. Enable adjustment.
  5. Press "Main" band [SCN] key to start scanning.
  6. When a tone/code is detected, it halts. Short press "Main" band DIAL to lock, then [SET] to save.

Various Scanning (VFO, Memory, Preferential Memory, Priority Channel)

The TH-9800Plus supports various scanning modes:

  • Scan-Resume Mode (Menu #25 SCAN): Select TIME (halts for 5 seconds, then resumes) or BUSY (resumes 2 seconds after carrier drops).
  • VFO Scanning: Select VFO mode, press [SCN] to start. Rotate DIAL for direction. Halts on signal, resumes per Scan-Resume mode. Press [SCN] to cancel.
  • Memory Scanning: Select Memory mode, press [SCN] to start. Halts on signal, resumes per Scan-Resume mode. Press [SCN] to cancel.
  • Skipped Channel during Memory Scan: Select Memory mode, select channel, press and hold [SCN] for 1/2 second to mark as "SKIP". Repeat to unmark.
  • Preferential Memory Scanning: Set up a "Preferential Scan List" by flagging channels with a "1" icon. Select Memory mode, select channel, press and hold [SCN] several times until "1" icon appears. To scan, select Menu #26 (SCAN M), set to "MSM", then press [SCN].
  • Programmable Memory Scan: Set sub-band limits by storing frequencies into Memory Channel #L1 (lower) and #U1 (upper). Switch to Memory mode, select L1, press and hold [V/M] for 1/2 second.
  • Priority Channel Scanning (Dual Watch): Checks a user-defined "Priority" Memory Channel for activity while operating on VFO, Memory, or Home channel.
    • VFO Priority: Recall desired memory channel as "priority". Select VFO mode. Press and hold [HM] for 1/2 second. Display remains on VFO frequency, but checks priority channel every 5 seconds. Press [V/M] to disable.
    • Memory Priority: Store desired frequency into memory channel "1". Operate on another memory channel. Press and hold [HM] for 1/2 second. Display remains on current memory channel, but checks channel "1" every 5 seconds. Press [V/M] to disable.

DTMF Signaling Operation

Two methods for DTMF signaling:

  • Using Microphone's Numeric Keys: Press and hold PTT, then input numbers (0-9, *, #, A, B, C, D).
  • Using DTMF Autodialer Feature: 16 DTMF autodialer memories (up to 16 digits) are available.
    1. To load: Enter Menu mode ([SET]), select Menu #12 (DTMF W). Select memory channel (d-1 to d-16). Input digits. Short press [SET] to save.
    2. To transmit: Enter Menu mode ([SET]), select Menu #15 (DTMF W). Short press [SET] to save. Press and hold PTT, then press "Main" band [HM] key.

2 Tone & 5 Tone Signaling Operation

2/5 Tone can only be sent via the autodialer feature (programmed via PC software).

  1. Select 2 Tone (Menu #38 2TONE) or 5 Tone (Menu #39 5TONE) memorized channel.
  2. Press and hold PTT, then press "Main" band [LOW] for 2 Tone or "Main" band [V/M] for 5 Tone.

Auto Range Transponder System (ARTS) Operation

ARTS uses DCS code to inform both parties when within communication range. Both stations must have the same DCS code and ARTS feature activated.

  1. Set DCS code.
  2. Enter Menu mode ([SET]), select Menu #3 (ARTS).
  3. Select ARTS beep option: IN.RNG (beep only on first detection) or ALWAYS (beep every time).
  4. Short press [SET] to confirm. "OUT.RNG" appears. ARTS operation commences.
  5. Every 25 seconds, your radio transmits a polling call. If no response, "OUT.RNG" appears.
  6. Press [SET] to exit ARTS operation.

Note: During ARTS operation, operating frequency or settings on the "Main" band cannot be changed.

Cross-band Repeater Operation

The TH-9800Plus can be set up to operate as a cross-band repeater via a simple Menu procedure.

  1. Configure both bands and squelch.
  2. Enter Menu mode ([SET]), select Menu #35 (X-PRT).
  3. Short press DIAL, "XSTART" appears.
  4. Short press DIAL again to activate. "CAN" icon disappears. Both bands can transmit/receive.
  5. Press [SET] to exit.

Note: Transmit duty cycle is higher; set power to Low. Operating frequency cannot be changed during cross-band repeater operation.

Microphone Key Assignments

The [P1]/[P2]/[P3]/[P4] buttons on the microphone can be assigned different functions.

  1. Enter Menu mode ([SET]).
  2. Select Menu #19-#22 (PG P1, PG P2, PG P3, PG P4).
  3. Select the desired function. Short press [SET] to save.

Menu Operation

To access and adjust menu settings:

  1. Short press [SET] to enter Menu mode.
  2. Turn the "Main" band DIAL to select a Menu item.
  3. Short press the "Main" band DIAL knob to enable adjustment, then rotate the DIAL to perform the adjustment.
  4. After adjustment, short press [SET] to save and exit.

A full list of menu items and their functions can be found in the user manual PDF: User manual (PDF).

Maintenance

Factory Reset Operation

To reset the transceiver to factory defaults:

  1. Turn the radio off.
  2. Press and hold the LEFT [LOW] key while turning the radio on.
  3. Rotate the DIAL to select the desired resetting menu:
    • F-1 SETMOD RESET: Resets menu settings.
    • F-2 HYPER RESET: Clears Hyper Memory settings.
    • F-3 MEMORY RESET: Clears regular Memory settings.
    • F-4 ALL RESET: Clears all memories and other settings.
  4. Short press the [SET] key to complete the reset.

Troubleshooting

If you encounter issues with your transceiver, refer to the table below for possible causes and solutions:

ProblemPossible Causes and Potential Solutions
Power is on, but nothing appears on the display."+" and "-" polarities of power connection are reversed. Connect Red lead to positive terminal and black lead to negative terminal of DC power supply.
Fuse is blown.Check and solve problem resulting in blown fuse and replace with new one.
Display is too dark.Adjust display brightness level to high.
No sound comes from speaker.Squelch is muted. Reduce squelch level. CTCSS/DCS and DTMF/2 TONE/5 TONE Squelch is active. Turn them off.
Key and Dial doesn't work.Keypad lock is activated. Disable it.
Press PTT key but TX doesn't work.Microphone or antenna connection is poor. Connect them properly.

If the PTT button doesn't work or there is no transmission, ensure the antenna and microphone are properly connected. If issues persist, contact support.

Specifications

General

ParameterValue
ModelTH-9800Plus
Frequency Range (RX only)108-135.995 MHz, 320-512 MHz, 750-950 MHz (Cellular Blocked)
Frequency Range (TX FM)26-33 MHz, 47-54 MHz, 136-174 MHz, 400-480 MHz
Channel Capacity809 Channels
Channel Spacing2.5/5/6.25/10/12.5/15/20/25/50 kHz
Modes of emissionF3
Antenna Impedance50 Ohms, unbalanced (Antenna Duplexer built-in)
Frequency Stability±5PPM @ -10℃ to +60℃
Operating Temperature Range-20℃ to +60℃
Operating Voltage13.8 V DC (±15%), Negative ground
Current Consumption (RX Squelched)0.5A
Current Consumption (TX)8.0A (50/430MHz), 8.5A (29/144MHz)
Case size (W×H×D)140 × 41.5 × 168 mm (w/o knobs & connectors)
Weight1.2 kg

Transmitter

ParameterValue
Output Power50/20/10/5W (29/50/144MHz), 40/20/10/5W (430MHz)
Modulation TypeVariable Reactance
Maximum Deviation±5KHz
Spurious Radiation-60dB (29MHz: < -50dB)
Modulation DistortionLess than 3%
Microphone Impedance2 kΩ

Receiver

ParameterValue
Circuit TypeDouble-conversion super-heterodyne
Intermediate Frequency (Left band)49.95 MHz / 450 kHz
Intermediate Frequency (Right band)38.85 MHz / 450 kHz
Sensitivity (for 12dB SINAD)<0.2 μV
Squelch Sensitivity<0.16 μV
Selectivity (-6dB/-60dB)12 kHz / 30 kHz
Maximum AF Output2W @ 8Ω for 5% THD
AF Output Impedance4-16Ω

US Version: 144-148 MHz / 420-450 MHz

Warranty and Support

A 12-month warranty is offered for the machine, and 6 months for accessories. If you encounter any issues, please contact your dealer for assistance.

For further assistance, you may refer to the official user manual PDF: User manual (PDF).

User Tips

  • Programming Software: Many users find it helpful to use programming software for setting frequencies and other functions. If you need the software, please contact the seller.
  • Antenna Selection: While the included antenna may be suitable for some uses, consider purchasing a dedicated antenna for specific bands (e.g., CB, UHF-VHF) for optimal performance, especially for mobile use.
  • Display Color: The display typically illuminates in yellow. The color cannot be changed.
  • AM Mode for CB Band: The radio can receive in AM mode on the CB band. For transmission in AM on the CB band, specific configurations or firmware versions might be required. Consult the seller or advanced user forums for details.
  • Heat Management: Some users have reported that the CMX138 chip can generate heat. Ensure adequate ventilation, especially during prolonged high-power transmissions or cross-band repeater operation.
  • Firmware Version: Check with the seller for the latest firmware version (e.g., 1901A, 2005A) as newer versions may include bug fixes or improved features.
Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.