ASYPDZSW VU358

Contents

ASYPDZSW VU358 VU Level LM358 Audio Meter Driver

Instruction Manual for DIY Kit / Finished Board with Adjustable Sensitivity

Brand: ASYPDZSW | Model: VU358

1. Introduction

The ASYPDZSW VU358 is a versatile VU Level LM358 Audio Meter Driver, available as either a DIY kit for enthusiasts or a pre-assembled finished board. This driver allows for independent adjustment of sensitivity for both left and right VU meter heads, ensuring precise control over your audio level display. It is designed to be integrated with various audio equipment such as headphone amplifiers, preamplifiers, and power amplifiers.

The board supports connecting two VU meter heads for stereo left and right channels. It also provides a DC voltage output for meter head backlights, with an adjustable RA resistor to control backlight brightness according to your preference.

2. Safety Precautions

  • Always set the preamplifier volume to minimum before powering on to avoid sudden loud noise or damage to speakers.
  • Strictly follow the turn-on / turn-off order provided in this manual to protect audio equipment and ensure stable operation.

3. Product Specifications

Feature Specification
Input Voltage AC 15-80V, 50-60Hz (Recommended: AC 12V)
Output Power 5W-1000W at 8 Ohm (Max. Power Per Channel: 101-130W)
PCB Size 50mm x 50mm
Channels 2 (2.0)
Control Method Others (Adjustable Sensitivity)

4. Package Contents

The ASYPDZSW VU358 is available in two configurations:

4.1. DIY Kit

This option includes all necessary components for self-assembly. You will receive:

  • 1x PCB (Printed Circuit Board)
  • Various electronic components (resistors, capacitors, diodes, ICs, terminal blocks, etc.)
  • Heat sink for voltage regulator
DIY Kit components for VU358 audio meter driver
Figure 1: Components included in the DIY Kit.

4.2. Finished Board

This option provides a pre-assembled and tested circuit board, ready for integration into your audio system.

Finished VU358 audio meter driver board, top view
Figure 2: Top view of the finished VU358 driver board.

Note: VU meter heads are not included with either the DIY kit or the finished board. This product is the driver circuit for the meters.

5. Setup

5.1. DIY Kit Assembly (for DIY Kit option only)

If you purchased the DIY kit, careful assembly is required. Ensure you have basic soldering skills and tools. Follow the component placement indicated on the PCB and ensure correct polarity for diodes, capacitors, and ICs. It is recommended to refer to the provided PDF manual for detailed assembly steps.

Important User Tip: Some users have noted the importance of ensuring a proper ground path for the 10µF capacitors. Verify that the negative terminal of the 10µF capacitor has a jumper or connection to the common ground output if not already present on the PCB design.

5.2. Wiring Connections

Connect the VU358 driver board to your audio system and VU meters as shown in the diagram below:

Wiring diagram for ASYPDZSW VU358 audio meter driver
Figure 3: Wiring Diagram for VU358 Driver Board.
  • AC 9-18V IN: Connect your AC power supply (recommended 12V).
  • L-IN, R-IN: Connect these to the Left (L), Ground (G), and Right (R) outputs of your amplifier.
  • L-OUT, R-OUT: Connect these to the Left and Right VU meter heads.
  • LED+: Connect to the positive terminal of your VU meter's backlight LEDs.
  • RA (LED Resistance): Adjust this resistor to achieve the desired brightness for your meter's backlight.

5.3. Sensitivity Adjustment

The board features blue adjustable potentiometers (variable resistors) for independently setting the sensitivity of the left and right VU meter heads. If the meter's response is too strong or too weak, use a small screwdriver to carefully turn these potentiometers until the desired sensitivity is achieved.

Video 1: Demonstration of VU meter driver in action, including sensitivity adjustment.

6. Operating Instructions

6.1. Turn-on Sequence

  1. Turn on the audio source (e.g., CD player, MP3 player, PC, digital player, or other audio source devices).
  2. Turn on the preamplifier (ensure its volume is set to minimum).
  3. Turn on the power amplifier.

6.2. Turn-off Sequence

  1. Turn off the power amplifier.
  2. Turn off the preamplifier.
  3. Turn off the audio source.

Adhering to this sequence helps prevent sudden loud noises and potential damage to your audio equipment.

7. User Tips

  • For DIY kit builders, pay close attention to the capacitor connections. Ensure the 10µF capacitor has a proper ground connection, as some board revisions might require a manual jumper.
  • If you experience unexpected behavior from the VU meters, double-check all solder joints and wiring connections, especially for the capacitors.
  • Experiment with the sensitivity adjustment potentiometers to find the optimal response for your specific VU meters and audio signal levels.

8. Troubleshooting

8.1. VU Meters Not Responding or Incorrectly

  • Check Wiring: Ensure all input, output, and power connections are secure and correctly wired according to the diagram in Section 5.2.
  • Power Supply: Verify that the AC 9-18V power supply is connected and providing the correct voltage.
  • Sensitivity Adjustment: Adjust the blue potentiometers (variable resistors) on the board. If the meters are not moving at all, try increasing the sensitivity. If they are always maxed out, decrease the sensitivity.
  • DIY Kit Specific: If you assembled the DIY kit, carefully inspect all solder joints for cold joints or bridges. Pay particular attention to the 10µF capacitors and ensure their negative terminals have a solid connection to ground.
  • VU Meter Compatibility: Ensure your VU meters are compatible with this driver board.

8.2. No Backlight on VU Meters

  • LED+ Connection: Verify the LED+ connection from the driver board to your VU meter's backlight.
  • RA Resistor: Adjust the RA resistor on the board. This resistor controls the current to the backlight LEDs. If it's too high, the LEDs might be dim or off.
  • LED Functionality: Check if the LEDs in your VU meters are functional.

9. Warranty and Support

This product is covered by a one-year warranty service from the date of purchase.

For technical support or warranty claims, please contact:

  • Company: XDH Tech
  • Address: 37 passage du Ponceau Bureau 270, Paris
  • Email: xdh.tech@outlook.com
  • Phone: +33 652768898

A comprehensive user manual in PDF format is also available for download: View User Manual (PDF)

© 2023 ASYPDZSW. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.