DEKO DNS-550E / DNS-980E

Contents

DEKO Solar Power Auto Darkening Welding Helmet

Models: DNS-550E / DNS-980E

1. Introduction

Thank you for choosing the DEKO Solar Power Auto Darkening Welding Helmet. This manual provides essential information for the safe and effective use of your welding helmet. Please read it thoroughly before operation and keep it for future reference.

The DEKO welding helmet is designed to protect your eyes and face from sparks, spatter, and harmful radiation under normal welding conditions. The auto-darkening filter automatically changes from a light state to a dark state when an arc is struck, and returns to the light state when welding stops, providing continuous protection.

2. Safety Information

Always wear appropriate personal protective equipment (PPE) when welding. This helmet protects against UV/IR radiation even in the light state. However, direct exposure to welding arc without the helmet in dark state can cause severe eye damage. Ensure the helmet is functioning correctly before each use.

  • Do not use the helmet if any part is damaged.
  • Do not immerse the helmet in water.
  • Do not use solvents on the filter screen or helmet components.
  • Ensure proper ventilation in your work area.
  • Always use the helmet within its specified operating temperature range.

3. Setup and Adjustment

3.1 Headband Adjustment

The headband is designed for individual needs to ensure a comfortable and secure fit. Proper adjustment is crucial for optimal protection and comfort.

  1. Adjustable Headband Length: Use the knob at the back of the headband to adjust the circumference to fit your head snugly.
  2. Adjustable Headband Tightness: The top strap can be adjusted to control how tightly the helmet sits on your head.
  3. Headband Fixed Knob: Use the side knobs to adjust the angle and distance of the helmet from your face.
Adjustable headband for DEKO welding helmet, showing length, tightness, and fixed knob adjustments.

The helmet allows for 180-degree rotation for convenience when not actively welding.

DEKO welding helmet shown rotating 180 degrees on a user's head.

3.2 Battery Installation

The welding helmet is powered by a combination of solar cells and replaceable lithium batteries.

  • DNS-550E: Requires 2xCR2032 lithium batteries.
  • DNS-980E: Requires 1xCR2450 lithium battery.

To install or replace batteries:

  1. Locate the battery compartment on the auto-darkening filter (ADF) unit.
  2. Open the compartment cover.
  3. Insert the new batteries, ensuring correct polarity (+/-).
  4. Close the compartment cover securely.

The solar cells assist in powering the ADF and extend battery life. However, the helmet relies on the lithium batteries for consistent performance, especially in low light conditions or when the solar cells are not sufficiently charged.

Internal view of DNS-550E lens with LED light adjustment display and removable 2xCR2032 Lithium Battery compartment.Internal view of DNS-980E lens with digital adjustment button and removable 1xCR2450 Lithium Battery compartment.

4. Operating Instructions

4.1 Auto-Darkening Function

The Auto Darkening Filter (ADF) automatically switches from a light state (DIN 4) to a dark state (variable shade 9-13 or 9-13.5) within 1/25000s (DNS-550E) or 1/10000s (DNS-980E) when welding begins. It returns to the light state when the arc is extinguished.

4.2 Controls and Adjustments

The helmet features controls for DELAY, SHADE, and SENSITIVITY to adapt to various welding environments and task durations.

  • DELAY: Adjusts the time it takes for the filter to return from dark to light state after welding stops. Adjustable from 0.1s to 1.0s (DNS-550E) or 0.1s to 2.0s (DNS-980E).
  • SHADE: Adjusts the dark shade level. The range is typically DIN 9-13 or 9-13.5. Select the appropriate shade based on your welding process and current.
  • SENSITIVITY (SENS): Adjusts the filter's sensitivity to ambient light and welding arc. Higher sensitivity means the filter will darken more easily.

For DNS-980E, a digital adjustment button allows for precise control, including a 'MODE' setting for switching between WELD (L5-8.5, H9-13.5) and GRIND (DIN4) functions.

4.3 Welding Applications

This helmet is suitable for a wide range of welding processes, including:

  • Manual Metal Arc Welding (MMA)
  • Metal Inert Gas Welding (MIG)
  • Metal Active Gas Welding (MAG)
  • Carbon Dioxide Welding (CO2)
  • Tungsten Inert Gas Welding (TIG)
  • Plasma Cutting
  • Arc Welding
  • Auto Welding

The DNS-980E model also includes a Grinding Feature, allowing the helmet to be used as a face shield for grinding operations (set to DIN4 light state).

Image showing the 'Clean Comfortable View' feature of the DEKO welding helmet, highlighting the clear viewing area and balanced design.Image showing the 'Mask Adjustment' feature of the DEKO welding helmet, emphasizing adaptability to different work environments.

5. Maintenance

5.1 Cleaning the Helmet and Filter

  • Regularly clean the helmet shell with a mild soap and water solution. Avoid harsh chemicals or abrasive cleaners.
  • Clean the auto-darkening filter (ADF) and protective lenses with a soft, clean cloth. Do not use solvents or alcohol-based cleaners, as these can damage the filter.
  • Replace scratched or damaged protective lenses immediately to maintain clear vision and protection.

5.2 Battery Replacement

When the low battery indicator blinks, or if the auto-darkening function becomes inconsistent, replace the lithium batteries as described in Section 3.2. Even with solar power, batteries have a finite life and need replacement.

5.3 Protective Lens Replacement

The outer and inner protective lenses are consumable parts and should be replaced when they become scratched, pitted, or otherwise impair vision. Spare protective lenses can be purchased separately from the seller.

6. Troubleshooting

ProblemPossible CauseSolution
Filter does not darken when arc is struck.Low battery; Sensors blocked; Incorrect sensitivity setting; Extreme cold.Replace batteries; Clean sensors; Adjust sensitivity; Allow helmet to warm up.
Filter remains dark after welding stops.Delay setting too high; Low battery.Adjust delay to a shorter time; Replace batteries.
Inconsistent darkening or flickering.Low battery; Sensors blocked; Interference from other light sources.Replace batteries; Clean sensors; Adjust sensitivity or reposition.
Poor visibility through the filter.Protective lenses scratched/dirty; Filter damaged.Clean or replace protective lenses; Replace ADF unit if damaged.
Low battery indicator blinks frequently.Batteries are low or depleted.Replace batteries immediately.

7. Specifications

The DEKO Auto Darkening Welding Helmets are available in two main models, DNS-550E and DNS-980E, with slight variations in features and performance.

FeatureADF DX550E (DNS-550E)ADF DX980E (DNS-980E)
Optical Class1/2/1/21/1/1/2
Viewing Area95*35mm98*80mm
Cartridge Size110*90*9.8mm133*114*10mm
Arc Sensor24
Light StateDIN 4DIN 4
Dark StateVariable shade, 9-13Variable shade, 5-8.5 / 9-13.5
Switch Time (Dark to Light)0.1s - 1.0s0.1s - 2.0s
Sensitivity1/25000s1/10000s
Power Supply2xCR2032 lithium battery + Solar Cells1xCR2450 lithium battery + Solar Cells
UV/IR ProtectionDIN 16DIN 16
Helmet MaterialPPPP
Weight530g530g
Recommended IndustryHeavy InfrastructureHeavy Infrastructure
User TypeProfessional and DIY HouseholdProfessional and DIY Household
Welding FeaturesTraditional HeadgearTraditional Headgear
Technical Details table comparing ADF DX550E and ADF DX980E models with specifications like optical class, viewing area, arc sensor, light/dark state, switch time, sensitivity, and power supply.Detailed specifications for DEKO DNS-550E welding helmet, including model number, view area, switch time, shade range, sensitivity, power supply, and battery type.Detailed specifications for DEKO DNS-980E welding helmet, including model number, view area, switch time, shade range, sensitivity, power supply, and battery type.

8. Warranty and Support

DEKO offers a one-year warranty for this product. Additionally, DEKO provides free lifetime technical support. For any issues or inquiries, please contact DEKO customer service.

DEKO Quality Service banner highlighting one-year warranty and free lifetime technical support.

9. User Tips

  • Battery Life: To prolong battery life, especially when not in use, store the helmet in a dark place or shade to prevent continuous charging by solar cells, which can drain the battery if the auto-darkening circuit is active.
  • Cold Weather Performance: The helmet has been reported to work well even in very cold temperatures (e.g., -30°C).
  • Shade Adjustment: For optimal visibility and protection, many users find a shade setting of 10-11 to be effective for general welding tasks.
  • Spare Lenses: It is advisable to have spare outer and inner protective lenses on hand, as they are consumables and can get scratched or damaged during use. These are typically sold separately.
  • TIG Welding: The helmet is suitable for TIG welding, including low amperage TIG (5amp AC/DC).

10. Product Overview Video

Watch this video for a general overview of DEKO tools, including some of the features and applications of their products.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.