STEPPERONLINE 17HS13-0404S1

Contents

Nema 17 Stepper Motor Instruction Manual

Brand: STEPPERONLINE | Model: 17HS13-0404S1

1. Introduction

This manual provides essential information for the proper installation, operation, and maintenance of your STEPPERONLINE Nema 17 Stepper Motor. This bipolar Nema 17 stepper motor is a popular model, featuring a 1.8-degree step angle and a compact size of 42x42x34mm. It comes with 4 wires, a 1-meter cable, and a 2.54mm pitch connector. Each phase draws a current of 0.4A at 12V, providing a holding torque of 26Ncm (36.8oz.in). It is ideal for various applications including 3D printers, CNC robotics, and Reprap projects.

Three Nema 17 stepper motors with wires
Figure 1: STEPPERONLINE Nema 17 Stepper Motors

2. Package Contents

Your package should contain the following items:

  • 3 x Nema 17 Stepper Motor (Model: 17HS13-0404S1)

3. Specifications

3.1. Electrical Specifications

Parameter Value
Manufacturer Part Number17HS13-0404S1
Motor TypeBipolar Stepper (HYBRID)
Phase2
Step Angle1.8 degrees
Step Accuracy (Non-Accumulative)±5.00%
Rated Current/Phase0.4A
Phase Resistance30 ohms ± 10%
Inductance37mH ± 20% (at 1KHz)
Holding Torque26Ncm (36.8oz.in / 0.26Nm)
EU LVD VoltageBelow 50Vac or 75Vdc
Insulation ClassB 130°C (266°F)

3.2. Physical Specifications

Parameter Value
Frame Size42 x 42mm
Body Length34mm
Shaft DiameterΦ5mm
Shaft TypeD-cut shaft
Front Shaft Length20mm
D-cut Length15mm
Number of Leads4
Lead Length1000mm (1m)
Weight230g

3.3. Environmental & Other Specifications

Parameter Value
Ambient Temperature-10°C to 50°C (14°F to 122°F)
Temperature RiseMax. 80°C
Wireless FunctionalityNo
Battery IncludedNo
High-concerned chemicalNone
CertificationCE, RoHS
OriginMainland China
Application3D printer, CNC robotics, Reprap project
Dimensional drawing of the Nema 17 stepper motor
Figure 2: Dimensional Drawing (All dimensions in millimeters)
CE and RoHS certifications for the stepper motor
Figure 3: CE and RoHS Certifications

4. Setup and Connection

To operate the Nema 17 stepper motor, you will need a compatible stepper motor driver (e.g., A4988, DRV8825, or similar). Ensure your driver can supply the rated current of 0.4A per phase.

4.1. Wiring

The motor features a 4-lead wiring configuration. Connect the motor leads to your stepper driver according to the diagram below. Incorrect wiring can damage the motor or driver.

Close-up of the 4-pin connector for the stepper motor
Figure 4: 4-pin Connector
Wiring diagram and step sequence for the stepper motor
Figure 5: Motor Connection and Full Step Sequence
Pin No. Bipolar Leads Winding
1A+BLK (Black)A+
2A-GRN (Green)A-
3B+RED (Red)B+
4B-BLU (Blue)B-

Full Step 2 Phase-Ex. Sequence (When facing mounting end):

Step A+ B+ A- B- Direction
1++--CCW
2-++-
3--++
4+--+CW

5. Operation

Stepper motors convert digital pulses into discrete mechanical movements. Each pulse from the driver moves the motor by one step (1.8 degrees for this model). By controlling the sequence and frequency of these pulses, you can precisely control the motor's position and speed.

  • Step Mode: Stepper motors can operate in full step, half step, or micro-stepping modes. Micro-stepping provides smoother motion and reduced resonance but requires more pulses per revolution.
  • Direction Control: The direction of rotation is determined by the sequence of phase energization.
  • Speed Control: The speed is controlled by the frequency of the step pulses. Higher pulse frequency results in higher motor speed.

Refer to your stepper motor driver's documentation for detailed programming and control instructions.

6. Maintenance

The Nema 17 stepper motor is designed for durability and requires minimal maintenance. Follow these guidelines to ensure optimal performance and longevity:

  • Operating Environment: Ensure the motor operates within the specified ambient temperature range of -10°C to 50°C (14°F to 122°F).
  • Cleanliness: Keep the motor free from dust, debris, and moisture. A clean operating environment helps prevent overheating and mechanical issues.
  • Connections: Periodically check all electrical connections to ensure they are secure and free from corrosion.
  • Shaft: Avoid applying excessive radial or axial loads to the motor shaft, as this can damage the bearings.

7. Troubleshooting

Here are some common issues and their potential solutions:

  • Motor not moving or erratic movement:
    • Check wiring connections against the diagram (Figure 5). Ensure correct phase connections.
    • Verify that the stepper motor driver is correctly configured and receiving step/direction signals.
    • Ensure the power supply to the driver is adequate and stable.
    • Check for mechanical obstructions preventing motor rotation.
  • Motor getting hot and vibrating excessively:
    • It is normal for stepper motors to generate some heat and vibration during operation, especially under load. The maximum allowable temperature rise is 80°C.
    • Ensure your driver current settings are appropriate for the motor's rated current (0.4A per phase). Setting the current too high will cause excessive heat.
    • Verify that the motor is not overloaded. Reduce the load if necessary.
    • Ensure adequate ventilation around the motor and driver.
    • Check for resonance issues; micro-stepping can help reduce vibration.
  • Loss of steps or inaccurate positioning:
    • Ensure the motor is not overloaded. The holding torque is 26Ncm.
    • Check for mechanical binding or friction in the system.
    • Increase the driver current (within the motor's rated limits) if the motor lacks sufficient torque.
    • Reduce the acceleration/deceleration rates in your control software.

8. User Tips

  • Driver Compatibility: Always use a dedicated stepper motor driver. Popular choices like the A4988 or DRV8825 are commonly used with Nema 17 motors. Ensure the driver's current capabilities match or exceed the motor's requirements.
  • Heat Management: While some heat is normal, prolonged operation near the maximum temperature rise (80°C) can reduce motor lifespan. Consider adding a heatsink to the motor or driver, or adjusting driver current if overheating is a concern.
  • Micro-stepping: For smoother operation and reduced noise, configure your stepper driver for micro-stepping (e.g., 1/8 or 1/16 micro-steps) rather than full-step mode.

9. Support

For technical assistance or further inquiries, please contact STEPPERONLINE Official Store support. You may also find additional resources and community forums online for 3D printing and CNC applications.

10. Additional Documents

A detailed user manual in PDF format is available for download. This document provides comprehensive information including detailed specifications and diagrams.

Reference: User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.