Bykski N-RTX2080TI-X

Contents

Bykski GPU Water Block Instruction Manual

Model: N-RTX2080TI-X

1. Product Overview

The Bykski N-RTX2080TI-X is a full-cover GPU water block designed to provide efficient cooling for select NVIDIA GeForce RTX 2080Ti and RTX 2080 series graphics cards. It features a copper base, high-quality acrylic top, and integrated A-RGB lighting for aesthetic customization.

Bykski N-RTX2080TI-X GPU water block, front view

Figure 1: Bykski N-RTX2080TI-X GPU Water Block (Front View)

2. Compatibility

This water block is designed for specific NVIDIA GeForce RTX 2080Ti, RTX 2080, RTX 2080 Super, RTX 2070 Super, RTX 2070, and RTX 2060 Super graphics cards. It is crucial to verify your GPU's PCB layout against the supported models to ensure compatibility. Using this block on an unsupported card may result in damage.

2.1 Supported GPU Models

Compatibility table for RTX 2080Ti graphics cards

Figure 2: Compatibility List for RTX 2080Ti

Compatibility table for RTX 2080 Super and RTX 2080 graphics cards

Figure 3: Compatibility List for RTX 2080 Super and RTX 2080

Compatibility table for RTX 2070 Super, RTX 2070, and RTX 2060 Super graphics cards

Figure 4: Compatibility List for RTX 2070 Super, RTX 2070, and RTX 2060 Super

If your specific GPU model is not listed or you are unsure, please contact Bykski support for verification.

3. Setup and Installation

Warning: Installing a GPU water block requires disassembling your graphics card. This process can void your GPU warranty if not performed correctly. Proceed with caution and at your own risk. Ensure your system is powered off and unplugged before starting.

3.1 Preparation

  1. Gather necessary tools: small Phillips head screwdriver, non-abrasive cloth, thermal paste, thermal pads (provided).
  2. Carefully remove your graphics card from your PC.
  3. Disassemble the stock cooler from your graphics card, following your GPU manufacturer's instructions.
  4. Clean the GPU die and memory chips thoroughly with isopropyl alcohol and a non-abrasive cloth to remove all old thermal compound and residue.

3.2 Step 1: Applying Thermal Compound and Placing Thermal Pads

Wipe off any remaining original thermal compound until components and the circuit board are completely clean. Apply thermal compound: lightly coat the NVIDIA GPU chip with the enclosed thermal grease. Place thermal pads on the circuit board as shown in the diagram below. Bykski provides more than adequate quantity of thermal pads.

  • Inductors do not need thermal paste.
  • The gray memory and MOS tube areas shown in the picture must have thermal pads, otherwise, components may burn out.
Diagram showing application of thermal compound and placement of thermal pads on GPU PCB

Figure 5: Thermal Compound and Pad Application

3.3 Step 2: Placing the Block on the Graphics Card

Carefully position the water block with preinstalled standoffs onto the graphics card. During this process, ensure you align mounting holes on the PCB with holes on the water block (same applies for other tops). Pay attention not to use too much force by pressing the block down to the PC, as chip dies are prone to cracking. This procedure is the same for all Full Cover water blocks.

3.4 Step 3: Attaching the Block to the Graphics Card

Bykski recommends using a screwdriver to start tightening the screws around the GPU core and continue outwards. Always use a plastic washer under each and every screw. If a washer is already present on the circuit board (usually around the four GPU core screw holes), there is no need for an additional washer.

Diagram showing placement and attachment of the water block to the graphics card

Figure 6: Water Block Placement and Attachment

3.5 RGB Lighting Connection

The water block features 5V A-RGB lighting. Connect the 3-pin A-RGB cable from the water block to a compatible 5V A-RGB header on your motherboard or a dedicated RGB controller. Ensure correct pin orientation (5V-D-G) to prevent damage.

LED Light Effect Display for 12V RGB and 5V A-RGB connections

Figure 7: RGB Lighting Connection Diagram

3.6 Integrating into a Water Cooling Loop

Connect your G1/4" fittings to the inlet and outlet ports of the water block. Ensure all connections are secure and leak-free. It is recommended to perform a 24-hour leak test with distilled water or a non-conductive coolant before powering on your system.

4. Operating Instructions

4.1 Water Cooling Operation

Once installed and leak-tested, the water block will actively cool your GPU by transferring heat to the circulating coolant. Monitor your GPU temperatures using software to ensure optimal performance.

4.2 RGB Lighting Control

The integrated 5V A-RGB lighting supports 16.7 million colors and various effects. It is compatible with major motherboard RGB synchronization technologies:

  • ASUS AURA SYNC
  • MSI MYSTIC LIGHT
  • GIGABYTE RGB FUSION
  • ASRock RGB LED

Control the lighting effects through your motherboard's RGB software or a compatible external A-RGB controller.

Bykski water block with RGB lighting and motherboard sync logos

Figure 8: RGB Lighting with Motherboard Sync Compatibility

5. Maintenance

  • Regular Inspection: Periodically check your water cooling loop for any signs of leaks, coolant discoloration, or debris buildup.
  • Coolant Replacement: It is recommended to replace your coolant every 6-12 months, depending on the coolant type and system usage, to prevent algae growth and corrosion.
  • Cleaning the Water Block: If performance degrades or visible buildup occurs, the water block may need to be disassembled and cleaned. Use distilled water and a soft brush to clean the microchannels. Avoid abrasive cleaners.
  • Acrylic Care: Clean the acrylic top with a soft, damp cloth. Do not use harsh chemicals or abrasive materials, as they can scratch or damage the acrylic.

6. Troubleshooting

6.1 Poor Cooling Performance

  • Check Installation: Ensure the water block is properly seated and tightened, and thermal paste/pads are correctly applied.
  • Coolant Flow: Verify that your pump is functioning correctly and there are no obstructions in the loop.
  • Air Bubbles: Bleed any air bubbles from the loop, as they can impede coolant flow and heat transfer.
  • Radiator/Fans: Ensure your radiator is clean and fans are operating at appropriate speeds.

6.2 Leaks

  • Tighten Fittings: Ensure all fittings are securely tightened. Do not overtighten.
  • O-Rings: Check O-rings on fittings and the water block for damage or improper seating.
  • Leak Test: Always perform a thorough leak test before powering on your system.

6.3 RGB Lighting Not Working

  • Connection: Verify the 3-pin A-RGB cable is correctly connected to a 5V A-RGB header on your motherboard or controller.
  • Software: Ensure your motherboard's RGB software is up-to-date and correctly configured.
  • Power: Check if the RGB controller (if used) is receiving power.

7. Specifications

ModelN-RTX2080TI-X
TypeVGA Front Water Block
MaterialCopper (T2 Copper, Thermal Conductivity: 401W/MK), High-quality Acrylic
Microchannel Structure0.5mm waterway spacing
RGB SupportA-RGB (3PIN 5V)
Port ThreadG1/4"
Dimensions (Approx.)Length: 243.29mm, Width: 127.30mm, Terminal Height: 120.01mm
Dimensional drawing (front and side views) of the N-RTX2080TI-X water block

Figure 9: Water Block Dimensions

Features diagram: Microchannel structure, High quality acrylic, T2 Copper

Figure 10: Key Features (Microchannel, Acrylic, Copper)

8. User Tips

  • Verify Compatibility: Always double-check the compatibility list and compare it with your GPU's PCB layout before purchase and installation. If in doubt, contact Bykski support directly.
  • Gentle Handling: GPU dies and water blocks are delicate. Apply even, gentle pressure during installation to avoid damage.
  • Leak Test is Key: Never skip the leak test. A thorough leak test can save your components from water damage.

9. Frequently Asked Questions (FAQ)

Q: Is this water block compatible with my [Specific GPU Model]?

A: Please refer to the detailed compatibility tables in Section 2.1. If your exact model is not listed, or if you have a custom PCB, it might not be compatible. It is recommended to contact Bykski support with your GPU's full model name and a picture of its PCB for confirmation.

Q: Does this water block include a backplate?

A: This product typically includes the GPU water block and mounting hardware. A backplate is usually sold separately unless explicitly stated in the product description or packaging. Please check the product listing for details.

Q: Can I use my original Founders Edition backplate with this water block?

A: In most cases, original backplates are not compatible with aftermarket water blocks due to differences in mounting points and thickness. It is generally recommended to use a backplate specifically designed for the water block or to operate without one if not critical for your setup.

10. Warranty and Support

Bykski products are covered by a manufacturer's warranty against defects in materials and workmanship. For specific warranty terms, duration, and to initiate a support request, please refer to the official Bykski website or contact your point of purchase. Always retain your proof of purchase.

For detailed installation guides and further product information, you may also consult the official Bykski user manual available at: Bykski User Manual (PDF).

© 2023 Bykski. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.