1. Introduction
The DOOYA DC73A Wireless Receiver is designed to provide remote control functionality for standard 4-wire tubular motors, commonly used in automatic curtain systems, blinds, and other motorized applications. This receiver operates on a 433MHz frequency and is compatible with DOOYA remote controls. It allows for convenient wireless operation of your motor, enabling precise control over movement (Up, Down, Stop).
2. Safety Information
- Ensure power is disconnected before installation or maintenance to prevent electric shock.
- Installation should be performed by a qualified electrician or technician.
- Do not expose the receiver to moisture, water, or extreme temperatures.
- Verify that the power supply voltage matches the receiver's specifications (220-240V).
- Keep out of reach of children.
3. Specifications
| Feature | Specification |
|---|---|
| Model Number | DC73A |
| Operating Frequency | 433MHz |
| Voltage | 220-240V |
| Wattage | 1W |
| Certification | CE |
| Origin | Mainland China |
4. Package Contents
- 1 x DOOYA DC73A Wireless Receiver Unit
Note: Remote control and motor are sold separately.
5. Setup and Installation
Follow these steps to install and connect your DOOYA DC73A Wireless Receiver:
- Power Disconnection: Before starting any wiring, ensure that the main power supply to the motor and the installation area is completely disconnected at the circuit breaker.
-
Access Receiver Terminals: Carefully open the casing of the DC73A receiver to expose the internal circuit board and wiring terminals.
Figure 2: Internal view of the DC73A receiver, revealing the circuit board and terminal block for wiring connections. -
Wiring Connections: Connect the 4-wire tubular motor and the main power supply to the receiver's terminal block. The terminals are typically labeled as follows:
- L (Live): Connect the Live wire from your main power supply.
- N (Neutral): Connect the Neutral wire from your main power supply.
- UP: Connect the 'Up' control wire from your 4-wire motor.
- DOWN: Connect the 'Down' control wire from your 4-wire motor.
- COM (Common): Connect the Common wire from your 4-wire motor.
Always refer to your motor's specific wiring diagram for exact wire color codes and functions. Ensure all connections are secure.
- Secure Casing: Once all wiring is complete and verified, carefully close and secure the receiver's casing.
- Restore Power: Reconnect the main power supply at the circuit breaker.
-
Pairing with Remote Control:
- Locate the programming button on the receiver (often a small button on the circuit board).
- Press and hold the programming button until the receiver indicates it's in pairing mode (e.g., an LED flashes or the motor jogs slightly).
- While in pairing mode, press the 'Up' or 'Stop' button on your DOOYA remote control.
- The receiver should confirm successful pairing (e.g., LED stops flashing, motor jogs again).
- Test the remote control to ensure proper operation of the motor.
Specific pairing procedures may vary slightly depending on the remote control model. Consult your remote control's manual for detailed instructions.
6. Operating Instructions
Once the receiver is installed and paired with a compatible DOOYA remote control, you can operate your tubular motor wirelessly:
- UP Button: Press to move the motor upwards (e.g., open curtains, raise blinds).
- DOWN Button: Press to move the motor downwards (e.g., close curtains, lower blinds).
- STOP Button: Press to halt the motor's movement at any desired position.
7. Maintenance
- Keep the receiver clean and free from dust. Use a soft, dry cloth for cleaning.
- Avoid exposing the unit to direct sunlight, high humidity, or corrosive environments.
- Do not attempt to repair the unit yourself. Refer to qualified service personnel.
8. Troubleshooting
- Problem: Motor does not respond to remote control.
-
- Check if the receiver has power (e.g., indicator light, if present).
- Ensure the remote control has fresh batteries.
- Verify that the remote control is properly paired with the receiver. If unsure, try re-pairing.
- Check for any obstructions or interference between the remote and receiver.
- Problem: Motor moves in the wrong direction (Up button makes it go Down).
-
- This indicates that the 'UP' and 'DOWN' wires from the motor are reversed at the receiver's terminal block. Disconnect power and swap these two wires.
- Problem: Motor does not move at all after installation.
-
- Ensure all wiring connections (Live, Neutral, Up, Down, Common) are secure and correctly matched according to the motor's diagram.
- Verify that the main power supply is active.
- Check if the motor itself is functioning correctly by testing it directly if possible.
9. User Tips
- Remote Control Compatibility: The DC73A receiver is designed for DOOYA remote controls. If you are using specific models like DOOYA DC90 or DC251, ensure they are compatible with the 433MHz frequency and the DC73A receiver model. Always check the remote's specifications or contact DOOYA support for confirmation.
- Wired Button Integration: While primarily a wireless receiver, some users inquire about compatibility with wired buttons for blinds. The DC73A is designed for wireless control via a remote. Integrating a wired button would typically require an additional wired control module or a different receiver model that supports both wired and wireless inputs. Consult a professional for such custom installations.
10. Warranty and Support
This DOOYA product comes with a manufacturer's warranty against defects in materials and workmanship. For specific warranty terms, duration, and to obtain technical support or service, please refer to the documentation provided with your purchase or contact your authorized DOOYA dealer or customer service.