1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of the eletechsup R421B16 16 Channel DC 12V RS485 Relay Module. This module is designed for remote control applications using the Modbus RTU protocol, suitable for integration with PLCs, PTZ cameras, motors, and other industrial or home automation systems.
2. Safety & Warnings
Failure to follow these instructions may result in damage to the product or personal injury.
- Read all instructions thoroughly before use.
- Keep the device and its cord out of reach of children under 3 years old.
- Keep away from children unless supervised by an adult.
- Do not use this product for purposes other than its intended use.
- Inspect the product before each use; do not use if damaged.
- Do not expose the module to water or excessive moisture.
- Handle with care to avoid cuts or injuries from sharp components or edges.
3. Specifications
| Feature | Specification |
|---|---|
| Model Number | R421B16 |
| Channels | 16 |
| Supply Voltage | DC 12V |
| Operating Voltage | DC 12V |
| Bus Interface | RS-485 (Modbus RTU) |
| Dissipation Power | 1W |
| Standby Current | 12mA |
| Application | Computer, PLC, PTZ Camera, Motor Control |
| Type | Drive IC |
| Operating Temperature | -20°C to 80°C |
| Dimensions (L x W x H) | 168 x 65 x 19 mm |
| Weight | 218g |
| Condition | New |
| Origin | Mainland China |
4. Setup
4.1 Initial Inspection
Before first use, carefully remove all protective films from the device. Inspect the module for any visible damage. If any damage is found, do not proceed with installation and contact support.
4.2 Power Connection
Connect a stable DC 12V power supply to the VIN and GND terminals on the module. Ensure correct polarity to prevent damage.
4.3 RS485 Communication Connection
Connect your RS485 master device (e.g., PLC, computer with RS485 adapter) to the module's A+ and B- terminals. Ensure that the A+ terminal of the master is connected to A+ on the module, and B- to B-.
4.4 Relay Output Connections
Each of the 16 relays provides three terminals: Normally Open (NO), Common (COM), and Normally Closed (NC). Connect your load according to your application's requirements:
- NO (Normally Open): The circuit is open when the relay is de-energized and closes when energized.
- COM (Common): The common terminal for the relay switch.
- NC (Normally Closed): The circuit is closed when the relay is de-energized and opens when energized.
Ensure that the current and voltage ratings of your loads do not exceed the relay's specifications (typically 10A 250VAC / 10A 30VDC).
4.5 Modbus Address Setting (DIP Switches)
The module's Modbus RTU address is set using the onboard DIP switches. The image (Figure 2) indicates "Save ID (A0-A5)" pointing to the DIP switch block. Consult the detailed Modbus protocol documentation (see Section 9) for specific DIP switch configurations corresponding to desired Modbus addresses.
5. Operating Instructions
The R421B16 module operates as a Modbus RTU slave device. It responds to commands from a Modbus master to control its 16 relays.
5.1 Modbus Communication
To operate the module, send Modbus RTU commands from your master device. The module supports standard Modbus functions for reading and writing coil (relay) states. You can read the current state of the relays and write commands to turn them ON or OFF.
For detailed information on Modbus addresses, function codes, and register mapping, please refer to the comprehensive user manual PDF available at https://manuals.plus/m/6f0ed55b059c0f5c00c1bce835864ecb6f0f877504bcab5cc4fa4235a8b8bcd3. This document will provide the necessary Modbus protocol details for effective communication.
5.2 Relay Control
Each of the 16 relays can be individually controlled. By sending the appropriate Modbus write command to the corresponding coil address, you can energize or de-energize a relay, thereby switching the connected load.
6. Maintenance
- Cleaning: Keep the module clean and free from dust and debris. Use a soft, dry cloth for cleaning. Do not use liquids or abrasive cleaners.
- Environment: Store and operate the module in a dry place, away from direct sunlight, extreme temperatures, and corrosive environments.
- Inspection: Periodically inspect all connections for tightness and signs of wear or corrosion. Check the module for any physical damage.
- Storage: When not in use, turn off the device and store it in a dry place.
7. Troubleshooting
- No Power Indication:
- Check the DC 12V power supply connection and ensure it is providing the correct voltage and current.
- Verify power supply polarity.
- Relay Not Switching:
- Confirm the Modbus address is correctly set via the DIP switches.
- Verify the Modbus communication wiring (A+ to A+, B- to B-).
- Check the Modbus commands sent from the master device for correctness (function code, coil address, value).
- Ensure the load connected to the relay is within its specified current and voltage limits.
- Communication Errors:
- Check RS485 wiring for shorts or open circuits.
- Ensure the baud rate, parity, and stop bits settings on the Modbus master match the module's default settings (or configured settings).
- Verify that the Modbus master is addressing the correct slave ID.
For more in-depth troubleshooting and specific Modbus register details, please consult the official user manual PDF.
8. User Tips
- Modbus Documentation: Users frequently inquire about Modbus addresses and functions. Always refer to the official PDF manual for the most accurate and complete Modbus protocol implementation details, including register maps for reading inputs and controlling outputs.
- Input/Output Control: The module is capable of both reading and writing to a single register for inputs and outputs in Modbus communication, allowing flexible control and monitoring.
- Software Testing: If you are looking for software test videos or examples, check the manufacturer's website or contact their support for available resources.
9. Warranty & Support
For warranty information, technical support, or any inquiries regarding the R421B16 module, please contact the manufacturer:
Manufacturer: Guangzhou Keshen Electronic Technology Co., Ltd
Email: eletechsup@163.com
Address: Room 301, No. 8-1 Beixin Street, Kemulang Aotou, Tianhe District, Guangzhou City, China
For a comprehensive guide and additional technical details, please refer to the full user manual PDF: https://manuals.plus/m/6f0ed55b059c0f5c00c1bce835864ecb6f0f877504bcab5cc4fa4235a8b8bcd3