1. Product Overview
This manual provides comprehensive guidance for the operation, maintenance, and troubleshooting of your SUNSUN external aquarium filter. This product series is designed for various aquatic environments, including tropical fish tanks, aquatic grass tanks, and saltwater tanks. It performs multi-stage filtration for efficient water purification, including physical and biochemical filtration, and some models feature a UV germicidal lamp.


2. Safety Precautions
Please read this manual carefully before using the product and keep it for future reference. Improper use may cause equipment damage or harm to aquatic life.
2.1 Electrical Safety
- Always disconnect power before installing, cleaning, or maintaining any electrical equipment (lights, water pumps, heaters) to avoid electric shock.
- Ensure power sockets are kept away from water sources.
- If the power cord is damaged, it must be replaced by the manufacturer or a professional technician.
2.2 Leakage Prevention
- Place the aquarium on a stable and firm surface.
- Pay attention to the water level when adding water to avoid overflow and short circuits.
- Keep covered lights at least 15mm away from the water surface.
2.3 Glass Products
- For glass products (such as aquariums, glass feeders), avoid collision or dropping.
- Dispose of broken glass properly as hazardous material; do not touch fragments directly with hands.
2.4 Chemical Products
- Keep water stabilizers, calcium additives, medicines, and other chemicals out of reach of children.
- In case of accidental contact with eyes, rinse immediately with plenty of water.
- These products are not for human consumption; do not ingest.
3. Setup Instructions
3.1 Unpacking and Placement
- Location Selection: Place the aquarium away from direct sunlight, heaters, and air conditioners. Direct sunlight causes excessive algae growth and unstable water temperature.
- Level Calibration: Ensure the aquarium is perfectly level to avoid cracking of silicone seals due to uneven pressure.
3.2 Water Filling and Leak Testing (New Tank Setup)
- Cleaning: Wipe the inside and outside of the aquarium with a soft cloth dampened with clean water. Do not use soap or chemical cleaners.
- Layered Water Filling: For stacked or sump filter tanks, layered filling is recommended. Fill the main tank first; water will flow into the sump automatically. Monitor the sump water level to avoid overflow when the pump starts.
- Disinfection: For initial use, add potassium permanganate (light purple solution) and circulate for at least 8 hours. Then drain and rinse thoroughly.
3.3 Filter Barrel Assembly

| No. | Part Name |
|---|---|
| 1 | Input And Output Discreteness |
| 2 | Barrelhead |
| 3 | Main Body |
| 4 | Light Tube |
| 5 | Draining Skep Cover |
| 6 | Draining Skep |
| 7 | Output Curvy Bar |
| 8 | Connected Bar |
| 9 | Spray Bar |
| 10 | Spray Bar Cover |
| 11 | Dirtiness Entrance |
| 12 | Connected Bar |
| 13 | Input Curvy Bar |
| 14 | Joint of Dirtiness Entrance |
| 15 | Input Bar |
| 16 | Input Cover |
| 17 | Sucking Disc for Fix |
| 18 | Pipe |

- Open the button to separate the barrel from the lid.
- After separating the lid, load the filter material (note: filter material is not included) and then install the filter basket.
- Pull up the rotary buckle, take in the water outlet assembly, install the pipeline, and then press the rotary buckle to fix the water outlet assembly.
- Install the inlet pipe in the aquarium as shown.
- Press the blue button firmly to the end, immediately release the hand. The inlet pipe begins to absorb water. Repeat this action until the hose water level is flush with the aquarium water level and then the power is turned on.
- In any case, when the filter bucket is separated from the bucket, a safety switch on the side will automatically close, and the UV light will automatically turn off to prevent injury to the human body.
3.4 UV Lamp Assembly (for models with UV lamp)

- Insert the UV lamp into the slot under the filter bucket cover.
- If the quartz glass cover is difficult to fix, hold the quartz tube and gently rotate it according to the direction shown in the picture.
4. Operating Instructions
4.1 Equipment Operation (Switches and Controls)
This product series is usually equipped with the following control switches:
- Light Switch: Controls the LED light on the aquarium hood.
- Water Pump Switch: Controls water circulation.
- Air Pump Switch: Controls oxygen aeration.
- Thermostat: Press and hold the power button to turn on. Use the up/down buttons to set the target temperature (e.g., 25°C). The display shows real-time water temperature.
4.2 Water Treatment Products
Water Conditioner (Dechlorinator / Stabilizer)
- Features: Quickly removes chlorine and neutralizes heavy metals in tap water; protects fish mucus and reduces stress.
- Usage:
- Calculate water volume: Length (cm) × Width × Height ÷ 1000 = Volume (L).
- Daily use: Add 10ml per 50L of water, once a week.
- Water change: Double dosage for new tanks or large water changes.
- Operation: Shake well before use. Pour directly into strong flow areas (e.g., sump pump chamber).
Nutritional Supplements & Trace Elements
- Features: Supplement vitamin B complex and trace elements; promote color enhancement, growth, and immunity.
- Usage: Add 10ml per 50L of water, once a week. Can be used during fish disease treatment.
Marine Salt (For Marine Products)
- Features: Made of pharmaceutical-grade raw materials, rich in 70 trace elements, suitable for corals and marine fish.
- Usage:
- Add marine salt to purified water in a clean container, stir evenly, and aerate.
- Target parameters: At 25°C, adjust specific gravity to 1.024–1.026.
- Water change: Replace 10%-15% of water weekly.
4.3 Fish Food and Feeding Tools
Feeding Guidelines
- Ingredients: Rich in protein (e.g., 60%), fat, and essential amino acids.
- Feeding Method:
- Frequency: 2–3 times daily.
- Quantity: Feed only what the fish can consume within 3–5 minutes to avoid leftover food polluting water.
- Storage: Seal tightly after each use. Store in a cool, dry place to prevent mold.
Glass Feeder
- Features: Avoid direct hand contact with food to prevent oil contamination.
- Steps:
- Remove the plug, insert the funnel, and fill with food (not more than half capacity).
- Press the feeding rod gently to control portion size. Do not submerge the feeding opening to avoid clogging.
- When not in use for a long time, empty food back into original packaging.
4.4 LED Lighting Equipment
- Installation: For indoor use only. Install on tank walls no thicker than 15mm to prevent falling into water.
- Operation: Connect to 220V~ 50Hz power supply.
- Disclaimer: The light source cannot be replaced by the user. Replace the entire fixture via dealer when expired.
- Cleaning: Disconnect power before wiping with a damp cloth.
5. Maintenance
5.1 Filtration System and Filter Media
- Mechanical Filtration: High-density filter sponge; clean every 1-2 weeks. Replace when worn or thinning.
- Chemical / Biological Filtration: Activated carbon, lava rock, and other media; replace every 2–3 months.
- Maintenance: Regularly check the pump impeller for debris; clean pipes to prevent blockage.
5.2 UV Lamp Maintenance

The germicidal lamp tube should be replaced after approximately 8000 hours of use, as its effectiveness will diminish. In case of normal power-on, if the UV lamp works normally, the indicator light will be on. If the indicator light is off, the UV lamp is broken, and you should replace it promptly.
6. Troubleshooting
- Pump not working:
- Cause: No power; impeller stuck.
- Solution: Check power; disassemble and clean impeller.
- Light not turning on:
- Cause: Switch off; LED lifespan ended.
- Solution: Check switch; replace entire light fixture.
- Cloudy water:
- Cause: Immature nitrification system; overfeeding.
- Solution: Add nitrifying bacteria; reduce feeding; increase aeration.
- Aquarium leaking:
- Cause: Silicone seal aging; overfilled water.
- Solution: Cut power immediately, relocate fish, contact after-sales service.
7. Specifications
Please refer to the specific model for detailed specifications. All models operate on 220V, 50Hz.
| Feature | HW-302 | HW-303A / HW-303B | HW-304A / HW-304B |
|---|---|---|---|
| Germicidal Lamp | No | HW-303A: No, HW-303B: Yes | HW-304A: No, HW-304B: Yes |
| Rated Power | 18W | 35W | 55W |
| UV Lamp Power | N/A | 9W (HW-303B only) | 9W (HW-304B only) |
| Maximum Lift | 1.4M | 2.0M | 2.5M |
| Maximum Flow | 1000L/H | 1400L/H | 2000L/H |
| Power Cord Length | 1.9M | 1.9M | N/A |
| Pipe Diameter (Outer) | 21MM | 21MM | 25MM |
| Dimensions (L*W*H) | 232*232*395MM | 258*258*430MM | 290*290*485MM |
| Filter Baskets | 3 | 3 | 4 |




8. User Tips
- Flow Rate Consideration: When selecting a filter, ensure the flow rate is appropriate for your aquarium size. For example, a 2000 L/H filter might be suitable for a 500-liter aquarium, but always verify compatibility with your specific tank and inhabitants.
- UV Lamp Handling: If your model includes a UV lamp, handle it with care during assembly and replacement. Ensure it is properly seated and the quartz glass cover is secure.
- Filter Media: The product does not include filter material. Remember to purchase appropriate filter media (e.g., sponges, activated carbon, bio-media) for your setup.
- Power Adapters: The product comes with a local adapter plug (e.g., EU, AU, UK 220V-50HZ). Ensure it matches your local power supply.
9. Warranty and Support
For detailed warranty information and customer support, please refer to the official user manual PDF available at: User Manual (PDF). This document contains additional information regarding product guarantees and service contacts.