TYT MD-UV390

Contents

TYT MD-UV390 DMR Digital Radio User Manual

Model: MD-UV390

Introduction

This manual provides comprehensive instructions for the safe and efficient use of your TYT MD-UV390 DMR Digital Radio. The MD-UV390 is a robust, waterproof (IP67 rated) dual-band VHF/UHF radio offering both digital (DMR) and analog communication modes with a 5W output power.

TYT MD-UV390 DMR Digital Radio highlighting 5W power, IP67 waterproof rating, LCD display, and dual band capabilities.

Figure 1: TYT MD-UV390 DMR Digital Radio overview.

Safety Information

Please read and understand all safety precautions before operating the radio. Failure to do so may result in injury or damage to the device.

  • Do not operate the radio in explosive atmospheres.
  • Do not expose the radio to direct sunlight for extended periods.
  • Use only approved batteries and chargers.
  • Do not disassemble or modify the radio.
  • Ensure the battery cover and accessory port covers are securely closed to maintain IP67 rating.

Package Contents

Verify that all items are present in your package:

  • TYT MD-UV390 Radio Unit
  • Antenna (VHF/UHF Dual Band)
  • Li-ion Battery Pack (2200mAh)
  • Desktop Charger with AC Adapter
  • Belt Clip
  • Hand Strap
  • User Manual
  • Programming Cable (optional, depending on package)

Setup

1. Attaching the Antenna

Screw the antenna clockwise into the connector on the top of the radio until it is firmly seated. Do not overtighten.

2. Installing the Battery

  1. Align the battery pack with the grooves on the back of the radio.
  2. Slide the battery upwards until it clicks into place.
  3. Ensure the battery release latch is engaged.
Image of the 2200mAh large capacity battery for the radio.

Figure 2: Large capacity 2200mAh battery.

3. Charging the Battery

  1. Place the radio (with battery installed) into the desktop charger.
  2. Ensure the charging indicator light illuminates (usually red).
  3. The light will typically turn green when charging is complete.
  4. A full charge may take several hours.

4. Initial Programming (Optional)

The MD-UV390 supports frequency programming via its easy-to-use screen interface. For advanced programming, such as setting up DMR contacts, talkgroups, and digital features, a programming cable and software are typically required. The software is usually provided by the manufacturer or can be downloaded from their official support website.

Two TYT MD-UV390 radios displaying the LCD screen, highlighting easy frequency programming and night use with backlight.

Figure 3: LCD display for simple frequency programming.

Operating Instructions

1. Power On/Off

Rotate the Power/Volume knob clockwise to turn the radio ON. Continue rotating to increase volume. Rotate counter-clockwise until a click is heard to turn the radio OFF.

2. Mode Selection (Digital/Analog)

The MD-UV390 operates in both Digital (DMR) and Analog modes. The mode is typically set per channel during programming. Refer to your programming software manual for details on setting channel modes.

3. Channel and Frequency Selection

Use the Channel Selector knob or the keypad to select a desired channel. In VFO (Variable Frequency Oscillator) mode, you can directly input frequencies using the keypad. To activate VFO mode, consult the radio's menu system or a specific key combination as detailed in the full programming guide.

Close-up of the TYT MD-UV390 radio's LCD display and ergonomic design for comfortable operation.

Figure 4: Ergonomic design and clear LCD display for easy operation.

4. Transmitting and Receiving

  • To Transmit: Press and hold the PTT (Push-To-Talk) button on the side of the radio. Speak clearly into the microphone. Release the PTT button to stop transmitting.
  • To Receive: The radio will automatically receive signals on the selected channel. Adjust the volume knob for comfortable listening.

5. Dual Band Operation

The MD-UV390 supports both UHF (400-480MHz) and VHF (136-174MHz) frequency bands. You can switch between bands or monitor both simultaneously depending on your programming and radio settings.

Comparison image showing labels for UHF (400-480MHz) and VHF (136-174MHz) frequency bands on the radio, indicating dual band capability.

Figure 5: Dual Band UHF/VHF frequency support.

Maintenance

  • Cleaning: Wipe the radio's surface with a soft, damp cloth. Do not use harsh chemicals or abrasive cleaners.
  • Battery Care: To prolong battery life, avoid overcharging and fully discharging the battery. Store the battery in a cool, dry place when not in use for extended periods.
  • Waterproof/Dustproof Integrity (IP67): The radio is rated IP67, meaning it can withstand immersion in 1 meter of water for up to 30 minutes and is fully protected against dust. Always ensure all port covers (e.g., accessory jack, USB port if applicable) and the battery compartment are securely sealed to maintain this rating. After exposure to water, dry the radio thoroughly before charging or opening any compartments.
TYT MD-UV390 radio submerged in water, demonstrating its IP67 dustproof and waterproof capabilities.

Figure 6: IP67 rating ensures protection against dust and water immersion.

Troubleshooting

ProblemPossible CauseSolution
Radio does not power on.Battery is low or not installed correctly.Charge the battery or re-install it securely.
Cannot transmit or receive.Incorrect frequency/channel selected; antenna not connected; out of range.Verify frequency/channel; ensure antenna is secure; move closer to other radios.
Poor audio quality.Low battery; antenna issue; interference.Charge battery; check antenna connection; move away from sources of interference.
Difficulty enabling VFO mode.VFO mode may be disabled in programming or requires a specific menu sequence.Consult the full user manual or programming guide for VFO activation steps. Ensure the radio is in a mode that allows VFO operation.

Specifications

FeatureDetail
Brand NameTYT
Model NumberMD-UV390
Walkie Talkie TypePortable
TypeDMR Digital Radio
Output Power (W)3W-5W
Frequency RangeDual Band 400-480MHz (UHF) / 136-174Mhz (VHF)
Storage Channel3000
Maximum Range3km-5km
Waterproof / Water-ResistantIP67
Is_DisplayYes
Battery Capacity (mAh)2200 mAh
Battery IncludedYes
Operating VoltageDC 7.4V (Rechargeable Li-ion battery)
MaterialStrong Polycarbonate Plastic
Dimensions123*60*35MM (Size Exclude the Antenna)
Net WeightAbout 260G
Channel Spacing12.5KHz
Antenna Impedance50 ohm
Working ModeDouble modes: Digital & Analogue Mode
Compatible withMototrbo Tier 1 Tier 2
CertificationCE, Dot, EAC, EPA, FCC, GMP, RoHS, TGA, UL, KC, pse, weee
OriginMainland China

User Tips

  • VFO Mode: If you are having trouble activating VFO (Variable Frequency Oscillator) mode, check the radio's menu settings. Some radios require VFO to be enabled in the programming software or via a specific key combination (e.g., pressing a dedicated VFO button or a function key + a number key). Refer to the detailed programming manual for your specific firmware version.
  • Programming Software: For advanced features and custom channel programming, you will need the appropriate programming software and cable. This software is typically available from the manufacturer's website.

Warranty and Support

The TYT MD-UV390 DMR Digital Radio comes with a One Year Warranty from the date of purchase. This warranty covers manufacturing defects under normal use. Please retain your proof of purchase for warranty claims.

For technical support, troubleshooting assistance beyond this manual, or warranty inquiries, please contact the seller or the manufacturer's customer service department. Contact information can usually be found on the seller's store page or the manufacturer's official website.

© 2023 TYT Electronics Co., Ltd. All rights reserved.

This manual is subject to change without notice.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.