1. Introduction
1.1 Overview
This diagnostic tool is specifically designed to work with all OBD II compliant vehicles, including those utilizing Controller Area Network (CAN). A small number of 1994 and 1995 model year gasoline vehicles are OBD II compliant. To verify if a 1994 or 1995 vehicle is OBD II compliant, check the Vehicle Emissions Control Information (VECI) Label. It is typically located under the hood or by the radiator. If the vehicle is OBD II compliant, the label will designate 'OBD II Certified'.
Government regulations mandate that all OBD II compliant vehicles must have a "common" 16-pin Data Link Connector (DLC).
1.2 On-Board Diagnostics (OBD) II
The OBD II system monitors emission control systems and key engine components by performing continuous or periodic tests. It provides information on whether the Malfunction Indicator Light (MIL) is commanded on or off, any stored Diagnostic Trouble Codes (DTCs), and Readiness Monitor status.
1.3 OBD II Definitions
The following terms are related to OBD II systems:
- EOBD: European On-Board Diagnostics, similar to OBD II with the same Data Link Connector and Communication Protocols.
- Communication Protocols: Allows different systems and sensors in a vehicle to communicate. Current protocols include CAN Bus, J1850 VPW, ISO 9141-2, J1850 PWM, and ISO 14230 KWP.
- PCM (Powertrain Control Module): The vehicle's on-board computer, controlling engine management, emissions, and powertrain operation. It can also communicate with other vehicle computers (e.g., ABS, ride control).
- DLC (Data Link Connector): The 16-cavity connector on the vehicle for communication between the computer system and the diagnostic tool.
- MIL (Malfunction Indicator Light): The vehicle's "Check Engine" warning light that activates when a DTC is stored.
- DTC (Diagnostic Trouble Code): A code stored in the computer system's memory, indicating a fault condition causing the MIL to activate.
- Freeze Frame Data: Operating conditions stored when a DTC is set.
- PID (Parameter Identification Data): Data returned by the vehicle's control modules to the diagnostic tool.
- Monitors: Diagnostic routines programmed into the PCM to run tests on emissions-related components.
- Enabling Criteria: Vehicle-specific events or conditions required for monitors to run.
- Trip: A specific driving sequence to meet enabling criteria for a monitor.
- Drive Cycle: A specific mode of vehicle operation to set all readiness monitors to "ready" condition.
- Warm-up Cycle: Vehicle operation after an engine-off period where engine temperature rises sufficiently.
- Fuel Trim (FT): Feedback adjustments to the base fuel schedule (short-term and long-term).
1.4 Diagnostic Trouble Codes (DTCs)
OBD II Diagnostic Trouble Codes are five-digit alphanumeric codes stored by the on-board computer diagnostic system in response to a problem. They guide you to the problem area. Do not replace parts based solely on DTCs; always consult the vehicle's service manual for proper testing procedures.
- The 1st character (B, C, P, or U) identifies the main system (Body, Chassis, Powertrain, or Network).
- The 2nd character (0-3) identifies the code type (Generic or Manufacturer-Specific).
- The 3rd character (0-9, A-F) identifies the specific system or sub-system.
- The 4th and 5th characters (0-9, A-F) identify the section of the system that is malfunctioning.
1.5 Location of the Data Link Connector (DLC)
The DLC is typically a 16-pin connector located within 12 inches of the center of the instrument panel, under or around the driver's side for most vehicles. For some vehicles, the location may vary. If you cannot find the DLC, refer to your vehicle's service manual.
2. Product Description
2.1 Components & Controls
- Charging LED: Red indicates charging, Green indicates fully charged.
- LCD: Displays test results and other information.
- USB Type-C port: Connects to the charging cable.
- DB-15 Diagnostic Connector: Connects the tool to the vehicle's DLC.
- Power Button: Turns the tool on or off.
2.2 Technical Specifications
- Screen: 5-inch touch screen
- RAM: 2 GB
- Storage: 32 GB
- OBDII Input Voltage Range: 9~18V
- Charging: DC 5V 2A charging cable or diagnostic cable via vehicle's DLC
- Dimensions: 228 mm x 125 mm x 34 mm
- Operating Temperature: 0°C to 50°C (32°F to 122°F)
- Storage Temperature: -20°C to 70°C (-4°F to 158°F)
- Charging Temperature: 0°C to 40°C (32°F to 104°F)
- Special Features: Wifi
- External Testing Certification: CE
- Batteries: Included
- Material: Plastic
*Note: The operating temperature refers to the temperature at which the scan tool works normally in non-charging status.
2.3 Packing List
The following items are typically included. Please consult the seller or the packing list supplied with your tool for exact contents:
- Diagnostic tool x 1
- OBD II diagnostic cable x 1
- Charging cable x 1
- User manual x 1
- Carrying bag x 1
3. Initial Use
3.1 Charging the Tool
There are two methods to charge the device:
- Via Charging Cable: Plug one end of the included charging cable into the Type-C port of the tool, and the other end into an external power supply device.
- Via Diagnostic Cable: Insert one end of the diagnostic cable into the DB-15 connector of the tool, and the other end into the vehicle's DLC.
The charging LED will illuminate solid green when the battery is fully charged.
3.2 Getting Started
For first-time use, you need to perform some system settings:
- Press the power button to turn on the tool.
- The screen will display a welcome page. Tap Start to proceed.
- Choose your desired system language from the list, then tap Next step.
- Choose your desired time zone, then tap Next step to enter the WLAN setup screen.
- Slide the Wi-Fi switch to ON. The system will search for available wireless LANs. Choose your desired WLAN access point/network. If the network is open, it will connect directly. If encrypted, you will need to enter the network password.
- After network connection, tap Next step to configure workshop information. Input the required details and tap Next step. This information will be appended to diagnostic reports.
- Carefully read all terms and conditions of the user agreement. Check the box before "Agree to all the above terms" and tap OK to finish the sign-up process and navigate to the Job Menu.
3.3 Job Menu
The main menu screen includes the following function modules:
| Module | Description |
|---|---|
| Local Diagnose | Configures the tool as a professional diagnostic tool. |
| Service Function | Offers coding, reset, relearn, and other service functions to restore vehicles to functional status after repair or replacement. |
| Other Modules | Includes add-on modules that extend the diagnostic tool's functionalities. |
| Upgrade | Updates vehicle diagnostic software and APK. Requires a stable network connection. |
| Mall | Allows subscription to extra vehicle diagnostic or reset software not included with the tool. |
| Know Your Customer | Assists repair shops with business analysis, customer management, diagnosis statistics, and service ranking. |
| Mine | Checks saved reports, order information, and allows system settings. |
| Toolbox | Provides practical add-on modules like battery voltage, diagnostic software clear, firmware fix, DTC library, diagnostic record, DLC lookup, feedback, and image management. |
| More | Includes Online support and LAUNCH Academy. |
4. Operating Instructions
4.1 Connection
- Turn the vehicle's ignition off.
- Locate the vehicle's 16-pin Data Link Connector (DLC). Refer to Section 1.5 for guidance.
- Plug one end of the diagnostic cable into the vehicle's DLC port, and the other end into the DB-15 diagnostic connector of the tool. Tighten the captive screws.
- A plastic DLC cover may need to be removed on some vehicles before plugging in the diagnostic cable.
- The cable connector is keyed and will only fit one way. If you encounter difficulty, rotate the connector 180° and try again.
- Turn the ignition on. The engine can be off or running.
- Press the power button for several seconds to turn the tool on and enter the Job Menu.
Caution: Do not connect or disconnect any test equipment while the ignition is on or the engine is running.
4.2 System Diagnostics
This function is designed to diagnose electronic control systems of a single vehicle model. Supported vehicle systems and diagnostic functions may vary based on product configurations.
4.2.1 Smart Diagnosis (Auto-Detect)
This function quickly accesses the vehicle's electronic control systems by decoding the VIN, eliminating manual menu selection. To enable, tap Mine -> Settings and set "Automatic detection on connect" to On. After connection and with the ignition key on, the system will auto-detect. Alternatively, if auto-detect is off, tap Local Diagnose -> AutoDetect to start manually.
- A stable network connection is recommended for successful VIN access.
- If auto-detection fails, try connecting to the network. Not all cars support Auto-Detect due to manufacturer settings.
If the system successfully obtains the VIN, confirm the information and tap OK to start diagnosing. A diagnostic report will be automatically generated. If VIN information cannot be accessed, the following screen will appear:
Input the VIN and tap OK. The system will attempt to decode the VIN and proceed with Smart Diagnosis. Otherwise, it will enter Manual Diagnosis mode.
- The VIN is typically located on the vehicle's dashboard (top left corner), driver's door, or firewall.
- VINs are standardized 17-character codes, using capital letters A-Z (excluding I, O, Q) and numbers 0-9.
4.2.2 Manual Diagnosis
If VIN information cannot be obtained or analyzed, you can perform vehicle diagnosis manually. Follow the on-screen instructions to proceed.
- Ensure corresponding vehicle manufacturer software is installed.
- The diagnostic menu may vary by vehicle make, model, and year.
To diagnose a vehicle manually:
- Select Local Diagnose.
- Select Vehicle Manufacturer.
- Select Vehicle Model.
- Select Scan Mode (Automatic System Detection or Manual System Detection).
- Select Test Function (Read Version Information, Read Fault Code, Clear Fault Code, Read Data Stream).
4.2.2.1 Health Report (Quick Test)
This function quickly accesses all electronic control units and generates a detailed report on vehicle health. Tap Health Report on the test item selection screen to start scanning ECUs. Once complete, the screen will display diagnostic results, showing fault codes in red and normal systems as "Normal" in green.
On-Screen Buttons:
- Enter: Selects other test functions.
- Report: Saves the diagnostic result as a report, accessible from Mine -> My Report.
- Clear Code: Clears existing diagnostic trouble codes.
4.2.2.2 System Scan
This option quickly scans which systems are installed on the vehicle.
4.2.2.3 System Selection
This option allows you to manually select the test system and function step-by-step. Tap System Selection on the test item selection screen, then select the desired system (e.g., Engine System) to enter the test function selection screen.
Available functions include:
- Version Information: Reads system mode, vehicle VIN, software, and ECU version information.
- Read Fault Code: Displays detailed information of DTC records. Each DTC has specific testing procedures; do not replace parts based solely on DTC definitions.
- Clear Fault Code: Erases codes from the vehicle after repairs. Ensure the ignition key is in the ON position with the engine off. Clearing codes does not fix the problem; proper repairs are necessary to prevent codes from reappearing.
- Read Live Data: Retrieves and displays live data and parameters from the vehicle's ECU.
4.2.2.3.1 Read Live Data
After selecting desired items, tap OK to enter the data stream reading page. Data can be viewed in three modes: Value (numbers and lists), Graph (wave patterns), and Combine (merged graphs for comparison).
On-Screen Buttons:
- Select All: Selects all items on the current page.
- Unselect: Deselects all data stream items.
- OK: Confirms selection and proceeds.
- Graph: Displays parameters in waveform graphs.
- Combine: Merges graphs for data comparison (up to 8 items).
- Report: Saves current data as a diagnostic report.
- Record: Records and saves Live Data for troubleshooting.
*Note: Data stream values out of the standard range will display in red; normal values in blue.
4.3 OBDII Diagnostics
This option provides a quick way to check for DTCs, isolate MIL causes, check monitor status for emissions testing, and verify repairs. After connecting the tool to the vehicle's DLC, tap OBD II on the Local Diagnose screen. The tool will automatically detect the communication protocol. Once a link is established, the Monitor Status will display. Tap OK to see the function list:
- Read I/M Readiness: Checks if emissions-related systems are operating properly for Inspection and Maintenance testing.
- Read Live Data: Retrieves and displays live data and parameters from the vehicle's ECU.
- Read Freeze Frame: Takes a snapshot of operating conditions when an emission-related fault occurs.
- Read Fault Code: Identifies the section of the emission control system that has malfunctioned.
- Clear Fault Code: Erases codes from the vehicle.
- Test Results: On-Board Monitoring Test: Retrieves test results for non-continuously monitored powertrain components.
- Control Operation of On-Board Component/System: Accesses vehicle-specific subsystem and component tests.
- Read Vehicle Information: Retrieves VIN, Calibration ID (CID), and Calibration Verification Number (CVN).
- EU OBFCM: Displays On-Board Fuel Consumption Monitoring data to check compliance with EU regulations.
4.4 I/M Readiness
This function provides quick access to I/M Readiness diagnostics.
4.5 History
The tool records every diagnostic session. The History function provides direct access to previously tested vehicles, allowing you to resume from the last operation. Tap History on the Local Diagnose screen to view diagnostic records in date sequence.
4.6 Service Function
The tool offers coding, reset, relearn, and other service functions to help vehicles return to functional status after repair or replacement. Available tests vary by vehicle manufacturer, year, and model. It is recommended to check for updates regularly to enjoy more service functions.
There are two methods for resetting operations: Manual Reset or Auto Reset. Auto Reset sends commands from the tool to the vehicle's ECU. Manual Reset requires users to follow on-screen instructions, select options, enter data, and perform necessary actions.
To perform a reset:
- Select Service Function.
- Choose the desired service function.
- Select the desired car brand.
- Select the reset mode (varies by vehicle).
- Follow the on-screen instructions to proceed.
5. Maintenance
5.1 Diagnostic Software Clear
This function allows you to delete diagnostic software that is not frequently used, freeing up storage space.
5.2 Firmware Fix
Use this module to upgrade and fix diagnostic firmware. During this process, do not cut power or switch to other interfaces.
5.3 Clean Up
This option allows you to clear cache files and free up storage space on the device.
6. Troubleshooting
6.1 DTC Library
This option allows you to retrieve detailed descriptions of specific DTCs from the DTC database. Swipe the screen upwards/downwards to alter the value, then press OK to display the DTC definition.
6.2 FAQ (Frequently Asked Questions)
This module lists some frequently asked questions and answers related to this tool. For a comprehensive list, refer to the tool's internal FAQ module.
7. Specifications
For detailed technical specifications, please refer to Section 2.2 of this manual.
| Attribute | Value |
|---|---|
| Model Name | CRP123E V3.0 |
| Item Type | Engine Analyzer |
| Special Features | Wifi |
| Voltage | 12V |
| Is Batteries Included | Yes |
| Item Weight | 1kg |
| Item Height | 10inch |
| Item Width | 12inch |
| Item Length | 11inch |
| External Testing Certification | CE |
| Software Version | NEWEST |
| Hardware Version | NEWEST |
| Material | Plastic |
| Supported Systems | Engine, ABS, Airbag (SRS), Transmission diagnostic |
| Supported Protocols | OBDII, EOBD, JOBD, KOBD |
| Key Functions | Fast VIN Auto detect, Automatically generate diagnostic reports, Battery tester, Full OBD2 Function |
| Vehicle Coverage | Over 10000 Car Models, Up to 57 Brands |
| Supported Languages | English, Spanish, French, German, Italian, Russian, Japanese, Korean, Portuguese |
| Update | Lifetime Free Update |
8. User Tips
- Vehicle Compatibility: Always verify your vehicle's OBD II compliance and specific model compatibility. While the tool supports a wide range of vehicles (57+ brands), specific advanced functions like ECU initialization, DPF regeneration, or transmission adaptations may vary by make, model, and year.
- Software Updates: Regularly update the diagnostic software to ensure access to the latest features, vehicle models, and improved performance. This can be done via Wi-Fi through the 'Upgrade' module.
- Language Settings: The tool supports multiple languages including English, Spanish, French, German, Italian, Russian, Japanese, Korean, and Portuguese. Ensure you select your preferred language during initial setup or via the settings menu for optimal usability.
- Advanced Functions: The device offers several reset services including Brake Reset, DPF Reset, ABS Bleeding, Battery Matching, Oil Reset, Steering Angle Reset, and Electric Throttle Relearn (TBI Adaptation). Refer to the 'Service Function' section for detailed instructions.
- Diagnostic Reports: Utilize the diagnostic report generation feature to save and review vehicle health information. These reports can be helpful for tracking vehicle maintenance and troubleshooting.
9. Warranty & Support
9.1 Warranty
LAUNCH electronic products are warranted against defects in materials and workmanship for one year (12 months) from the date of delivery to the user. This warranty does not cover parts that have been abused, altered, used for purposes other than intended, or used inconsistently with instructions. The exclusive remedy for any defective automotive meter is repair or replacement. LAUNCH is not liable for consequential or incidental damages.
Final determination of defects is made by LAUNCH. No agent, employee, or representative of LAUNCH has authority to bind LAUNCH to any affirmation, representation, or warranty concerning LAUNCH automotive meters, except as stated herein.
9.2 Customer Service
If you have any questions regarding the operation of the unit, contact the seller or the LAUNCH TECH Service Center.
- Website: https://en.cnlaunch.com
- Phone: +86 755 8455 7891
- Email: overseas.service@cnlaunch.com
A detailed operation manual is integrated into the tool for quick reference. You can also find a PDF version of the user manual at: User manual (PDF).