DSPIAE MT-C

Contents

DSPIAE MT-C Stepless Adjustment Circular Cutter User Manual

Model: MT-C (Advanced Kit) & MT-CL (Locator)

1. Introduction

The DSPIAE MT-C Stepless Adjustment Circular Cutter is an advanced tool designed for precision cutting of circular items in model assembly and craft work. It is ideal for cutting masking tape or plastic sheets up to 0.4mm thick, perfect for detailing and masking jobs. The MT-CL Locator (available separately or as part of a kit) assists in accurate and repeatable positioning.

This cutter is uniquely designed to save you time when cutting circular items. With its stepless adjustment, your modeling work can be done more effectively and easier than ever.

DSPIAE Stepless Circular Cutter Advanced Kit and Locator
Figure 1: DSPIAE Stepless Circular Cutter - Advanced Kit and MT-CL Locator.

2. Safety Information

  • Warning: professional modeler only. This tool is intended for experienced users.
  • Keep out of reach of children under 14 years of age.
  • Read instructions carefully before use to avoid possible injury caused by improper use.
  • DO NOT use this cutter on metal sheets or plastic sheets thicker than 0.4mm.
  • The Locator (MT-CL) is available separately and is only compatible with the advanced circular cutter kit (MT-C).
  • Do not drop or tap this product, as this may cause damage or malfunction.

3. Package Contents

3.1. Stepless Circular Cutter - Advanced Kit (MT-C)

  • Stepless Circular Cutter-Advanced Kit x1
  • ABS Storage Case With Magnetic Lock x1
  • Silicon Anti Slip Pad x1
  • 30° Tungsten Carbide Cutting Bit x1
  • 45° Tungsten Carbide Cutting Bit x1
  • 60° Tungsten Carbide Cutting Bit x1
  • Allen Hex Key x3

3.2. Stepless Circular Cutter - Locator (MT-CL) (Optional/Sold Separately)

  • Aluminium Alignment Block x1
  • Acrylic Locator Piece x1
  • Silicon Anti Slip Pad x1
Packing Details for DSPIAE Circular Cutter and Locator
Figure 2: Visual representation of package contents.

4. Specifications

FeatureMT-C (Advanced Kit)MT-CL (Locator)
Product NameStepless Circular Cutter-Advanced KitStepless Circular Cutter-Locator
ModelMT-CMT-CL
Measurement95*95*26mm75*75*8mm
ConstructionAluminium Alloy, 440 High Grade Stainless SteelAluminium Alloy, Acrylic
Weight315g ± 3g87g ± 3g
Blade MaterialTungsten SteelN/A
Blade Angle≤ 60 °N/A
Blade Length0.3cmN/A
Handle Length2.7cm (for blade holder)N/A
Sharp BladeYesN/A
Spring ForceNoN/A
LockNoN/A
High-concerned chemicalNoneNone
DIY SuppliesPaint & DecoratingN/A
Specifications table for DSPIAE Circular Cutter and Locator
Figure 3: Detailed specifications for the cutter and locator.

5. Setup

  1. Unboxing: Carefully remove all components from the packaging. Verify that all items listed in the 'Package Contents' section are present.
  2. Install Cutting Bit: Select the desired tungsten carbide cutting bit (30°, 45°, or 60°) and securely install it into the cutter's blade holder. Ensure it is firmly seated.
  3. Attach Anti-Slip Pads: Before first use, attach the provided silicon anti-slip pads to the bottom of the cutter and the locator (if applicable) to prevent movement during operation.
Video 1: Product demonstration showing blade installation and cutting action.

6. Operating Instructions

6.1. Basic Circular Cutting

  1. Prepare Material: Place the material to be cut (masking tape or plastic sheet, max 0.4mm thickness) on a suitable cutting mat.
  2. Adjust Radius: Use the stepless adjustment mechanism on the cutter to set the desired radius. The radius scale indicates disc sizes from 1mm up to 45mm diameter.
  3. Position Cutter: Place the cutter on the material, ensuring the center pin is at the desired center of your circle.
  4. Cut: Apply gentle, even pressure and rotate the cutter to make a clean circular cut. Multiple light passes are recommended for thicker materials to avoid tearing or uneven cuts.
Circular cutter in use, showing quick cutting of masking tape or plastic sheets
Figure 4: The circular cutter in action, ideal for materials under 0.4mm thickness.
Size limitation diagram for circular cutter
Figure 5: The cutter can produce circles from 1mm to 45mm in diameter.

6.2. Using the MT-CL Locator for Accurate Positioning

The MT-CL Locator is designed to assist in repeated and accurate positioning of the circular cutter.

  1. Determine Position: Determine the position of the disc to be cut out on your material.
  2. Place Locator: Put the MT-CL Locator over the determined position. Use the concentric engravings on the acrylic locator piece as a visual reference for the approximate position of the disc to be cut out.
  3. Align Cutter: Carefully remove the locator (the alignment block should remain untouched). Align the circular cutter using the corner of the alignment block as a guide (without screws against the block).
  4. Cut: Once aligned, proceed with cutting as described in section 6.1.
Accurate positioning with the MT-CL locator
Figure 6: The MT-CL Locator ensures precise and repeatable positioning for your cuts.
Steps for using the locator and making concentric cuts
Figure 7: Visual guide for positioning the locator and aligning the cutter.

6.3. How to Make Concentric Cutting

To create concentric circles (a ring shape), follow these steps:

  1. Cut Inner Circle: First, cut the inner circle to your desired diameter.
  2. Set Outer Diameter: Without moving the material or the alignment block (if using the locator), adjust the cutter to the required diameter for the outer circle.
  3. Verify Position: Double-check that the alignment block's position remains exactly the same.
  4. Cut Outer Circle: Proceed to cut the outer circle.
Steps for using the locator and making concentric cuts
Figure 8: Visual guide for making concentric cuts.

7. Maintenance

  • The Advanced Kit (MT-C) is designed to be maintenance-free.
  • Regularly clean the cutter and locator with a soft, dry cloth to remove any dust or material residue.
  • Store the cutting bits in their designated slots within the storage case to prevent damage and maintain sharpness.
  • Replace cutting bits when they become dull to ensure clean and precise cuts.

8. Troubleshooting

  • Uneven or Ragged Cuts:
    • Check if the cutting bit is dull. Replace it if necessary.
    • Ensure the material thickness does not exceed 0.4mm.
    • Apply consistent, gentle pressure during cutting. Avoid excessive force.
    • Make multiple light passes instead of one heavy pass, especially on thicker materials.
  • Inaccurate Circle Size/Shape:
    • Verify that the radius is correctly set on the cutter.
    • Ensure the material and cutter do not shift during the cutting process. Use the anti-slip pads and the MT-CL Locator for stability.
    • When using the locator, ensure the alignment block remains perfectly still between steps.
  • Cutter Not Moving Smoothly:
    • Check for any debris or residue obstructing the movement of the cutter. Clean thoroughly.
    • Ensure the cutting surface is flat and even.

9. User Tips

  • This stepless circular cutter is an ideal solution for achieving perfectly cut discs, especially for smaller diameters, which are often challenging to cut freehand.
  • Utilize the precision cuts for advanced masking techniques in model painting. For example, spray parts with a first color, then mask with discs cut from masking tape where needed. After the first color dries, spray the second color. Once dry, remove the masks to reveal the color underneath, achieving perfect, crisp lines every time.
Actual applications of circular cutter for masking
Figure 9: Example of using precision-cut masks for detailed model painting.

10. Compliance

⚠️ Warning: Please comply with the applicable laws and regulations in your jurisdiction before purchasing. Any illegal use of the product for any illicit activities is strictly forbidden and may result in legal consequences.

© 2024 DSPIAE. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.