SUNSUN HW-302/303/304/402/403/404/504/505/507/702/703/704/HW3000/HW5000

Contents

SUNSUN Aquarium Filter Rotor Instruction Manual

Models: HW-302, HW-303, HW-304, HW-402, HW-403, HW-404, HW-504, HW-505, HW-507, HW-702, HW-703, HW-704, HW3000, HW5000

1. Product Overview

This manual provides essential information for the installation, operation, maintenance, and troubleshooting of SUNSUN Aquarium Filter Rotors. These rotors are critical components for maintaining proper water circulation and filtration in your aquarium system. Each rotor model is designed for specific SUNSUN filter series to ensure optimal performance.

Assortment of SUNSUN filter rotors
Figure 1: Various SUNSUN Aquarium Filter Rotors

2. Compatibility and Setup

It is crucial to select the correct rotor for your specific SUNSUN aquarium filter model. Using an incompatible rotor may lead to reduced performance, increased noise, or damage to the filter unit. Refer to the compatibility list below:

  • HW302 Rotor is suitable for: HW302A/B, HW402A/B, HW507A/B, HW702A/B series filters.
  • HW303 Rotor is suitable for: HW303A/B, HW403A/B, HW703A/B series filters.
  • HW404 Rotor is suitable for: HW304A/B, HW404A/B, HW704A/B series filters.
  • HW504 Rotor is suitable for: HW504A/B, HW505A/B series filters.
  • HW3000 Rotor is suitable for: HW3000 series filters.
  • HW5000 Rotor is suitable for: HW5000 series filters.

Note: Compatibility is only guaranteed for SUNSUN brand filters as specified. Use with other brands is not recommended and may not function correctly.

Installation Steps:

  1. Disconnect Power: Always unplug your aquarium filter from the power source before performing any maintenance or installation.
  2. Access Impeller Chamber: Open your filter unit according to its specific instructions to access the impeller chamber. This usually involves removing the filter head.
  3. Remove Old Rotor: Carefully pull out the old rotor and its shaft. Inspect the chamber for any debris or blockages.
  4. Insert New Rotor: Place the new rotor's shaft into the designated slot in the impeller chamber. Ensure it is seated correctly and can spin freely.
  5. Reassemble Filter: Securely reattach the filter head and any other components removed.
  6. Reconnect Power: Plug the filter back into the power source and ensure it starts operating normally. Check for proper water flow and listen for unusual noises.

3. Operating Instructions

Once the new rotor is installed, ensure the filter is primed according to your filter model's instructions (if applicable) before turning it on. The rotor should spin smoothly, creating consistent water flow through the filter. Monitor the filter's performance for the first few hours to ensure stable operation.

4. Maintenance

Regular maintenance of your filter rotor is essential for the longevity and efficiency of your aquarium filter. Over time, debris can accumulate on the rotor or shaft, leading to reduced performance or failure.

  • Routine Cleaning: During regular filter maintenance (e.g., monthly or bi-monthly), remove the rotor and gently clean it with a soft brush under running water. Remove any algae, detritus, or mineral buildup from the impeller blades and the ceramic shaft.
  • Inspect for Wear: Periodically inspect the rotor and its shaft for signs of wear, such as cracks, chips, or excessive play. A worn rotor can cause increased noise or decreased flow.
  • Replacement: Rotors are wear-and-tear parts and will eventually need replacement. Replace the rotor if you notice significant wear, persistent noise, or a noticeable drop in filter performance despite cleaning.

5. Troubleshooting

Common Issues and Solutions:

  • Filter Not Starting/No Flow:
    • Ensure the filter is plugged in and receiving power.
    • Check if the rotor is properly seated in its chamber.
    • Inspect the rotor and impeller chamber for any obstructions (e.g., gravel, plant matter, snails).
    • Verify the rotor is not damaged or excessively worn.
  • Increased Noise/Vibration:
    • Remove and clean the rotor and impeller chamber thoroughly. Debris can cause imbalance.
    • Check the ceramic shaft for damage or wear.
    • Ensure the rotor is correctly installed and seated.
    • If the noise persists, the rotor may be worn and require replacement.
  • Reduced Flow:
    • Clean the rotor and impeller chamber.
    • Check for blockages in the filter media or hoses.
    • Inspect the rotor for wear or damage.

6. Specifications

The following tables provide detailed dimensions for each rotor model. All measurements are approximate and may have minor manual measurement errors.

HW302 Rotor Dimensions

HW302 rotor with dimensions
Figure 2: HW302 Rotor Dimensions
Measurement Value
Overall Length67.2 mm
Rotor Diameter15 mm
Impeller Width45 mm
Shaft Length30.4 mm
Shaft Diameter5.5 mm
Impeller Height32.7 mm
Impeller Thickness6 mm

HW504 Rotor Dimensions

HW504 rotor with dimensions
Figure 3: HW504 Rotor Dimensions
Measurement Value
Overall Length73.8 mm
Rotor Diameter16 mm
Impeller Width50.9 mm
Shaft Length31.3 mm
Shaft Diameter6 mm
Impeller Height35.5 mm
Impeller Thickness6 mm

HW303 Rotor Dimensions

HW303 rotor with dimensions
Figure 4: HW303 Rotor Dimensions
Measurement Value
Overall Length88.1 mm
Rotor Diameter19 mm
Impeller Width57.8 mm
Shaft Length32.8 mm
Shaft Diameter6 mm
Impeller Height42.5 mm
Impeller Thickness7.9 mm

HW404 Rotor Dimensions

HW404 rotor with dimensions
Figure 5: HW404 Rotor Dimensions
Measurement Value
Overall Length77.7 mm
Rotor Diameter21 mm
Impeller Width52.3 mm
Shaft Length32.9 mm
Shaft Diameter8.2 mm
Impeller Height43.1 mm
Impeller Thickness7.8 mm

HW3000 Rotor Dimensions

HW3000 rotor with dimensions
Figure 6: HW3000 Rotor Dimensions
Measurement Value
Overall Length80.14 mm
Rotor Diameter19 mm
Impeller Width51 mm
Shaft Length36.1 mm
Shaft Diameter8 mm
Impeller Height42 mm
Impeller Thickness7.4 mm

HW5000 Rotor Dimensions

HW5000 rotor with dimensions
Figure 7: HW5000 Rotor Dimensions
Measurement Value
Overall Length104.5 mm
Rotor Diameter27 mm
Impeller Width89.5 mm
Shaft Length49 mm
Shaft Diameter15 mm
Impeller Height67.5 mm
Impeller Thickness10 mm

7. User Tips

  • Verify Compatibility: Always double-check the model number of your filter against the rotor's compatibility list before purchasing to ensure a perfect fit.
  • Quiet Operation: If your new rotor is making more noise than expected, ensure it is fully seated and that the impeller chamber is free of any debris. Sometimes, a new rotor needs a short break-in period.
  • Regular Inspection: Incorporate rotor inspection into your routine filter cleaning schedule to catch wear or damage early.

8. Warranty and Support

For warranty information, technical support, or replacement parts beyond the rotor, please refer to the original documentation provided with your SUNSUN aquarium filter or contact SUNSUN customer service directly. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.