1. Introduction
The GEYA 4 Channel Relay Module is designed for PLC output load current amplification and isolation protection. It is typically installed at the digital output terminal of PLCs, MCU industrial control boards, time relays, buttons, and other controllers. This module amplifies the output current for high-power equipment and provides weak current control, thereby protecting the control system from potential damage.
This manual provides essential information for the safe and efficient use of your GEYA 4 Channel Relay Module. Please read it thoroughly before installation and operation.
2. Key Features
- DIN Rail mountable design, suitable for TS15/28/35 widths.
- Features 4 independent Normally Open (NO) and Normally Closed (NC) relay contacts (1 SPDT per channel).
- Built-in MPA Electromagnetic relays, certified with CCC and CE standards.
- High switching capacity: up to 10A at 250VAC or 30VDC.
- Flexible input connections via screw terminal blocks, supporting both NPN & PNP common use, and AC & DC common use.
- Each relay channel includes an LED status indicator, surge suppression protection, and overvoltage protection.
- Available in various input voltages: 5VDC, 12VAC/DC, 24VAC/DC, 230V.
3. Specifications
3.1 Technical Data
| Parameter | Value |
|---|---|
| Input Operate Voltage | DC/AC±10 % (Available: 5VDC, 12VAC/DC, 24VAC/DC, 230V) |
| Relay Mounting | PCB Soldered |
| Allowable Switching Voltage | 10A 250VAC/30VDC |
| Contact Rating | 10A |
| Input Current per Channel | 5.3mA |
| Operating Time | 10ms max |
| Release Time | 5ms max |
| Input/Output Connection | Screw Connection |
| Suitable Cable | 0.2~2.5mm² |
| Stripping Length | 6-7mm |
| Din Rail Mounting Size | 15/28/35mm |
| Dielectric strength | 2.5KV, 50Hz, 1MIN |
| Ambient temperature | -20°C ~ 50°C |
Note: The specific input voltage (e.g., 5VDC, 12VAC/DC, 24VAC/DC, 230V) is determined by the model variant purchased.
3.2 Dimensions
Figure 1: Dimension diagram for GEYA Relay Modules. The diagram shows top and side views with measurements in millimeters. The 4-channel module has dimensions of 70mm (width) x 85mm (height) x 43.5mm (depth).
| Relay Quantities | Dimension (mm) |
|---|---|
| 1 | 18×85×43.5 |
| 2 | 40×85×43.5 |
| 4 | 70×85×43.5 |
| 8 | 130×85×43.5 |
| 16 | 250×85×43.5 |
4. Setup and Installation
4.1 Mounting
The GEYA Relay Module is designed for DIN Rail mounting. It is compatible with TS15, TS28, and TS35 DIN rail widths. Ensure the module is securely clipped onto the DIN rail in your control cabinet or enclosure.
Figure 2: Side view of the GEYA Relay Module, illustrating the integrated clips for secure DIN rail mounting.
4.2 Wiring Connections
All input and output connections are made via screw terminal blocks. Use appropriate wiring practices and ensure all connections are tight and secure.
- Input Connections: The module supports NPN & PNP common use, and AC & DC common use. Connect your control signals (e.g., from PLC, MCU) to the input terminals (X0, X1, X2, X3 for a 4-channel module) and the common (COM) terminal.
- Output Connections: Each channel provides 1 Normally Open (NO) and 1 Normally Closed (NC) contact, along with a Common (COM) terminal. Connect your load to the appropriate output terminals.
- Cable Requirements: Use cables with a cross-section of 0.2~2.5mm². Strip approximately 6-7mm of insulation from the cable ends before inserting into the terminals.
Wiring Example (FY-T734C)
Figure 3: Wiring examples for the FY-T734C module, showing both NPN and PNP input configurations. The diagram illustrates how to connect DC+ and DC- for input, and the NC, NO, and COM terminals for output.
General Wiring Diagram (NT731C, NT732C~16C)
Figure 4: General wiring diagram showing the internal circuitry for single-channel (NT731C) and multi-channel (NT732C~16C) relay modules. It details the input bridge rectifier and the output relay contacts (NC, NO, COM).
5. Operating Instructions
Once properly installed and wired, the GEYA 4 Channel Relay Module operates by receiving control signals at its input terminals to switch the connected loads.
- Power On: Apply the specified input operate voltage (e.g., 5VDC, 12VAC/DC, 24VAC/DC, 230V) to the module's input terminals.
- Signal Input: Provide a control signal from your PLC, MCU, or other controller to the respective channel input (X0-X3) and common (COM) terminals.
- Relay Activation: Upon receiving the appropriate control signal, the corresponding relay will activate. The LED status indicator for that channel will illuminate, confirming the relay's state.
- Load Switching: The activated relay will switch the connected load according to its Normally Open (NO) or Normally Closed (NC) configuration.
The module is designed for general purpose use, making it versatile for various automation and control applications.
6. Maintenance
To ensure optimal performance and longevity of your GEYA 4 Channel Relay Module, follow these general maintenance guidelines:
- Regular Inspection: Periodically check all wiring connections to ensure they remain tight and free from corrosion. Inspect the module for any signs of physical damage, overheating, or discoloration.
- Cleaning: Keep the module clean and free from dust, dirt, and moisture. Use a soft, dry cloth for cleaning. Do not use abrasive cleaners or solvents.
- Environmental Conditions: Ensure the module operates within the specified ambient temperature range of -20°C to 50°C. Avoid exposing the module to excessive humidity or corrosive environments.
- Power Off Before Maintenance: Always disconnect power to the module and any connected loads before performing any inspection or maintenance to prevent electrical shock.
7. Troubleshooting
If you encounter issues with your GEYA 4 Channel Relay Module, refer to the following troubleshooting steps:
- Relay Not Activating:
- Verify that the correct input operate voltage is applied to the module.
- Check the control signal from your PLC/MCU. Ensure it is within the module's specified input voltage range.
- Inspect all input wiring for loose connections or breaks.
- Confirm that the LED status indicator is not illuminating when a signal is present.
- Load Not Switching:
- Ensure the relay is activating (check the LED indicator).
- Verify that the load is correctly wired to the NO/NC and COM terminals.
- Check the load itself for proper functionality and ensure it is not drawing excessive current beyond the 10A rating.
- Inspect output wiring for loose connections or breaks.
- Module Overheating:
- Ensure the ambient temperature is within the specified operating range.
- Verify that the load current does not exceed the maximum allowable switching current of 10A.
- Check for proper ventilation around the module.
- No Power/No Indicators:
- Check the main power supply to the control system.
- Verify the input operate voltage connections to the module.
If the problem persists after following these steps, contact GEYA customer support for further assistance.
8. User Tips
- Versatile Application: This relay module is designed for general purpose use, making it highly adaptable for various automation and control scenarios in different environments.
- Load Capacity: Always ensure that the connected load does not exceed the module's maximum rated load current of 10A at 250VAC or 30VDC to prevent damage and ensure reliable operation.
- DIN Rail Compatibility: The module's compatibility with TS15, TS28, and TS35 DIN rails offers flexibility in mounting within standard electrical enclosures.
9. Warranty and Support
For warranty information, technical support, or any inquiries regarding your GEYA 4 Channel Relay Module, please refer to the official GEYA website or contact your local distributor. Ensure you have your product model number (FY-T734 Relay Module) and purchase details available when seeking support.