1. Introduction
Thank you for purchasing the QYT KT-8900R tri-band mobile radio. The KT-8900R is unique for its compact body, powerful output, and tri-band frequency range design. It is also designed with a new and personalized operation menu to give you an easy-to-use and exceptional operating experience. We believe its mini size and cost-effective price will well meet your demand.
Before operation and to obtain the best performance, we recommend you to read this user manual carefully to become familiar with the features and uses.
2. Safety Information
MATTERS NEED ATTENTION!
Please observe the following precautions to prevent fire, personal injury, or damage to the radio:
- Do not use this machine when driving, as it can be dangerous.
- This radio is designed to use 13.8 V DC voltage. Do not use a 24 V power supply for the mobile radio.
- Please do not place the machine in dust, moisture, or where it may be exposed to water splashing.
- If there's any electromagnetic interference, please keep the mobile radio away from sources such as TV sets, engine generators, etc.
- Do not expose the mobile radio to long periods of direct sunlight, for example, on the dashboard of a vehicle or close to heating appliances.
- If the mobile radio generates any smoke or strange smell, please turn off the power supply immediately and ensure all is safe. Then, you can send the unit to the nearest after-sale center for inspection or repair.
- Do not keep transmitting with high power output for too long, which may lead to overheating and cause auto power off or failure.
3. Unpacking and Product Inspection
Welcome to use our mobile radio KT-8900R. Before operation, it is recommended that you:
- Please check the package is in good condition without any damage.
- Please unpack the package box carefully and check that all items are included.
- If you find any items are missing or have been damaged during shipment, please contact your dealer immediately.
Standard Accessories

- Mobile Radio
- Speaker Microphone
- Mounting Bracket
- Cigar-plug Power Cable
- Screws & Fuse
4. Panel Description
Front Panel Controls and Switches

- Progress Knob: Used for various selections and adjustments.
- TX Indicator: Illuminates when transmitting.
- Display Screen: Shows frequency, channel, and menu information.
- Power Indicator: Indicates power status.
- Volume Knob: Adjusts audio volume.
- PC Programming Socket: For connecting to a computer for programming.
- Function Key (F): Press to enter menu selection mode.
- Monitor (MONI): Press to turn on/off the squelch.
- Call Key (CALL): In standby, sends caller ID; in transmit, sends repeater activation.
- Mode Switch (V/M): Switches between channel mode and frequency mode.
- FM Radio (FM): Enters or exits FM radio mode.
- A/B Band Switch, Emergency Alarm (A/B/EXIT): Selects A/B band or exits menu. Press and hold for 2 seconds to activate alarm.
- Power On/Off (POW): Press and hold to turn the radio on or off.
- Microphone Connector: Connects the speaker microphone.
Speaker Microphone Description

- MENU: Function key.
- UP: Tune up channel step.
- DOWN: Tune down channel step.
- EXIT/A/B: Exit A/B channel switch, emergency alarm etc.
- */SCAN: Offset function, scan, digital.
- #/LOCK: Keypad lockout function, digital.
- 0-9: Number keys.
5. Setup
Frequency Range Setting
To set the frequency range, press and hold the [F] key while turning on the radio. The screen will display "PASSWD". Input the correct six-digit password. The display will then show "135 179", allowing you to set the tri-band frequency ranges:
- VHF: 135-179MHz (e.g., input "136 174" for 136-174MHz).
- VHF: 240-270MHz (e.g., input "240 260" for 240-260MHz).
- UHF: 400-520MHz (e.g., input "400 480" for 400-480MHz).
Once the frequency range is successfully programmed, you can only operate within this range.
Password Setup
Users can set up a six-digit password for PC programming. Remember this password, as you will not be able to read or write data without it.
Programming Cable Connection
To program the radio via PC, connect the WIN10-USB-KT8900 programming cable. The USB end connects to your computer, and the 3.5mm jack connects to the PC Programming Socket on the radio's rear panel, next to the cooling fan.
Manual Memory Channel Storage
To store a frequency in memory:
- In VFO mode, input the desired frequency (e.g., 435.125MHz).
- Select desired RX CTCSS/DCS (refer to menu 10 and 11) and TX CTCSS/DCS (refer to menu 12 and 13). For example, press [F] Key + [1] Key + [1] Key + [F] Key + [DOWN] Key to select RX CTCSS 67.0Hz, then [F] Key + [EXIT/AB] Key to save. Repeat for TX CTCSS.
- Refer to menu 36 (MEM-CH) to store the memory channel. Press [F] Key + [3] Key + [6] Key + [F] Key + [UP] Key to store the information.
Memory Channel Deletion
To delete a memory channel, refer to menu 37 (DEL-CH). Press [F] Key + [3] Key + [7] Key + [F] Key + [UP] Key to select the desired channel, then press [F] Key to delete it.
FM Radio Memory Channel Storage
FM radio memory channels and their names are PC programmable. In FM mode, you can press [*] to auto-search for FM signals.
Keypad Lock-out
In standby mode, press and hold the [#] Key for 2 seconds to turn the keypad lock on or off.
6. Operating the Radio
Menu Function Setup (via Speaker Microphone)
The radio features an extensive menu system for configuring various parameters. Access the menu by pressing the [F] Key on the radio's front panel or the MENU button on the speaker microphone. Use the number keys to navigate to specific menu items and the [F] Key to save settings. Below are some key functions:
- TDR (Dual Standby): Enable/Disable dual standby function. (Menu 0)
- STEP (Channel Step): Select channel step in frequency mode (5KHz, 6.25KHz, 10KHz, 12.5KHz, 25KHz). (Menu 1)
- SQL (Squelch Level): Adjust squelch level from 0 (off) to 9. (Menu 2)
- TXP (Transmitting Power): Set high or low transmitting power. (Menu 3)
- SCR (Scrambler): Activate/deactivate audio encryption. (Menu 4)
- TOT (Time Out Timer): Set transmission time limit (15-600s). (Menu 5)
- WN (Wide/Narrow Bandwidth): Select 25KHz (wide) or 2.5KHz (narrow). (Menu 7)
- ABR (LCD Backlight Time): Set backlight duration or always on. (Menu 8)
- BEEP (Key Tone): Turn key tone on/off. (Menu 9)
- R-DCS/R-CTCS (RX DCS/CTCSS): Set receive Digital Coded Squelch or Continuous Tone-Coded Squelch. (Menu 10, 11)
- T-DCS/T-CTCS (TX DCS/CTCSS): Set transmit Digital Coded Squelch or Continuous Tone-Coded Squelch. (Menu 12, 13)
- DTMFST (DTMF Side Tone): Configure DTMF tone emission (OFF/KEY/ANI/BOTH). (Menu 15)
- BCL (Busy Channel Lockout): Prevent transmission on a busy channel. (Menu 16)
- SC-ADD (Scan Add): Add/remove channel from scan list. (Menu 17)
- PRI-SC/PRI-CH (Priority Scan/Channel): Setup priority scan and select priority channel. (Menu 18, 19)
- SC-REV (Scan-Resume Mode): Configure scan resume behavior (Time Scan, Carrier Scan, Search Scan). (Menu 20)
- PTT-ID: Configure PTT-ID transmission (OFF/BOT/EOT/BOTH) and delay time. (Menu 23, 24)
- EMC-TP (Emergency Alarm Mode): Set emergency alarm behavior (Alarm only, ANI, or Both). (Menu 26)
- CHNAME (Channel Name): Edit channel names in Channel Mode. (Menu 29)
- AUTOLK (Keypad Auto Lockout): Enable/disable automatic keypad lockout. (Menu 32)
- PONMSG (Power-on Message): Configure display upon power-on (Full screen, Message, Battery voltage). (Menu 33)
- WT-LED/RX-LED/TX-LED (Backlight Color): Set standby, receive, and transmit backlight colors (OFF/BLUE/ORANGE/PURPLE). (Menu 34, 35, 36)
- SFT-D/OFFSET (Offset Direction/Frequency): Set repeater offset direction (+/-) and frequency. (Menu 39, 40)
- ANI/ANI-L (ANI Code/Length): Configure Automatic Number Identification code and its length. (Menu 41, 42)
- REP-S/REP-M (Repeater Activation/Transpond): Setup repeater activation tone and transpond mode. (Menu 43, 44)
- TDR-AB (Dual Standby): Enable/disable dual standby. (Menu 45)
- SET/RP-STE (Squelch Tail Elimination): Enable/disable squelch tail elimination. (Menu 46, 47)
- RPT-DL (Repeater Delay Time): Set delay time to receive repeater signal. (Menu 48)
- RESET: Reset menu mode or all settings to factory default. (Menu 49)
Transmitting Repeater Signalling
To transmit a desired repeater signalling tone (four tones selective):
- Press [F] Key + [4] Key + [2] Key + [F] Key + [UP] Key to select the desired tone.
- Press [F] Key to store the setting.
- Press the [CALL] Key to emit the pre-programmed repeater signalling tone.
PTT ID Setting
PTT-ID codes are pre-programmed via PC software.
- Select desired signalling in menu 20. Press [F] Key + [2] Key + [0] Key + [F] Key + UP(DOWN) to select, then [F] Key to save.
- Set PTT transmit time in menu 22. Press [F] Key + [2] Key + [2] Key + [F] Key + UP(DOWN) to select, then [F] Key to save.
- Select PTT transmit delay time in menu 23. Press [F] Key + [2] Key + [3] Key + [F] Key + UP(DOWN) to select, then [F] Key to save.
- Press [PTT] to send the programmed ID code.
Optional Signalling Setup (DTMF)
This radio supports DTMF encode/decode. Users can program DTMF codes via PC software. When a matched DTMF code is received, the radio will alert and display the corresponding code, allowing communication between radios. To transmit DTMF signalling:
- Select DTMF signalling in menu 20. Press [F] Key + [2] Key + [0] Key + [F] Key + UP(DOWN) to select, then [F] Key to save.
- Select signalling code in menu 24. Press [F] Key + [2] Key + [4] Key + [F] Key + UP(DOWN) to select, then [F] Key to save.
- In standby mode, press the [Call] Key to transmit the selected DTMF code.
Patrol Function
When the radio receives a pre-programmed patrol code, it will emit its self ID code, which will be displayed on the master control radio. This function can be controlled by a master ID code (programmable via PC software).
Monitor Function
Upon receiving a pre-programmed monitor code, the radio will transmit to monitor surrounding voice. This function can be controlled by a master ID code (programmable via PC software).
Remote Stun
When a pre-programmed remote stun code is received, transmission is disabled, and an alert is shown on the display. The radio will only resume normal operation after a remote revive. This function can be controlled by a master ID code (programmable via PC software).
Remote Kill
Upon receiving a pre-programmed remote kill code, transmission, reception, and all activities are disabled, with an alert on the display. The radio will only resume normal operation after a remote revive. This function can be controlled by a master ID code (programmable via PC software).
Remote Revive
When a pre-programmed remote revive code is received, the radio will be revived and restore to normal operation. This function can be controlled by a master ID code (programmable via PC software).
Emergency Alarm
When a pre-programmed emergency alarm code is received, the radio will emit an emergency alarm. The emergency alarm mode and channel are PC programmable. This function can be controlled by a master ID code (programmable via PC software).
2 Tone and 5 Tone Signalling
The radio supports 2 Tone and 5 Tone signalling, which are PC programmable. When matched signalling is received, the radio will activate corresponding functions (e.g., ring and display code). To transmit 2 Tone or 5 Tone signalling, press the [CALL] Key after selecting the appropriate options in the menu (Menu 20 OPTSIG, Menu 24 INFO).
7. Maintenance
To ensure optimal performance and longevity of your QYT KT-8900R mobile radio, follow these general maintenance guidelines:
- Cleaning: Use a soft, damp cloth to clean the exterior of the radio. Do not use harsh chemicals or abrasive cleaners. Ensure no moisture enters the device.
- Storage: Store the radio in a cool, dry place away from direct sunlight and extreme temperatures.
- Inspection: Periodically check cables and connectors for any signs of wear or damage.
- Avoid Impact: Protect the radio from drops and impacts, which can damage internal components.
8. General Specifications
General
| Feature | Specification |
|---|---|
| Frequency Range | VHF: 136-174MHz, 240-260MHz; UHF: 400-480MHz (460-520MHz) |
| Channel Capacity | 200 channels |
| Channel Spacing | 25KHz/20KHz/12.5KHz |
| Channel Step | 5KHz, 6.25KHz, 10KHz, 12.5KHz, 15KHz, 25KHz |
| Working Voltage | 13.8V DC ± 15% |
| Squelch Way | CTCSS / DCS / 5Tone / 2Tone / DTMF |
| Frequency Stability | ± 2.5ppm |
| Operating Temperature | -20℃ ~ +60℃ |
| Dimensions (W x H x D) | 98mm x 35mm x 118mm |
| Weight | 408g |
Receiver (ETSI EN 300 086 Standardized Test)
| Feature | Wide Band | Narrow Band |
|---|---|---|
| Sensitivity | ≤0.25μV | ≤0.35μV |
| Adjacent Channel Selectivity | ≥70dB | ≥60dB |
| Intermodulation | ≥65dB | ≥60dB |
| Spurious Rejection | ≥70dB | ≥70dB |
| Audio Response | +1~-3dB (0.3~3KHz) | +1~-3dB (0.3~2.55KHz) |
| Hum & Noise | ≥45dB | ≥40dB |
| Audio Distortion | ≤5% | |
| Audio Output Power | ≥2W@10% | |
Transmit (ETSI EN 300 086 Standardized Test)
| Feature | Wide Band | Narrow Band |
|---|---|---|
| Output Power | 25W/20W (VHF/UHF) | |
| Modulation Mode | 16K0F3E | 11K0F3E |
| Adjacent Channel Selectivity | ≥70dB | ≥60dB |
| Hum & Noise | ≥40dB | ≥36dB |
| Spurious Emission | ≥60dB | ≥60dB |
| Audio Response | +1~-3dB (0.3~3KHz) | +1~-3dB (0.3~2.55KHz) |
| Audio Distortion | ≤5% | |
Attention: Above specifications are subject to change without any notice due to technology enhancement.
9. User Tips
- Frequency Range: The radio supports tri-band frequencies (VHF 136-174MHz, 240-260MHz, UHF 400-480MHz). Ensure your desired operating frequencies fall within these ranges.
- Programming: For advanced configuration and setting up specific features like PTT-ID or custom channel names, PC programming is required. Make sure to use the correct programming cable and software.
- Antenna: For optimal performance, ensure you use an antenna suitable for the tri-band frequencies this radio operates on.
10. Warranty and Support
For detailed warranty information, troubleshooting, and further support, please refer to the complete user manual PDF available at: QYT KT-8900R User Manual (PDF). You may also contact the seller or authorized service center for assistance.