ASLONG JGA25-371

Contents

JGA25-371 Geared Motor User Manual

Model: JGA25-371

1. Introduction

This manual provides essential information for the safe and efficient use of your JGA25-371 Geared Motor. This micro DC motor features an integrated gearbox and a Hall encoder for precise speed and position feedback. Please read this manual thoroughly before installation and operation.

JGA25-371 Geared Motor side view
Figure 1: JGA25-371 Geared Motor

2. Intended Use

The JGA25-371 Geared Motor is designed for a wide range of applications requiring controlled rotational motion and feedback, including:

  • Robotics projects
  • Electric bicycles
  • Home appliances
  • Automotive applications
  • Small fans
  • Other DIY and industrial automation projects

This motor is suitable for use in environments where its operating voltage (6-24VDC) and torque specifications are met. Do not use this motor for purposes other than those specified by the manufacturer or in conditions exceeding its technical limits.

3. Technical Specifications

The JGA25-371 motor comes in various configurations, primarily differing in their gearbox reduction ratio, which affects the output speed and torque. The rated voltage for these configurations is 12V.

JGA25-371 Geared Motor Specifications Table, Wiring Diagram, and Dimensions
Figure 2: Detailed Specifications, Wiring, and Dimensions

General Specifications:

  • Operating Voltage Range: 6-24VDC
  • Rated Voltage: 12V
  • Construction: Other (Geared Motor)
  • Commutation: Brush
  • Protect Feature: Other
  • Certification: CCC
  • Origin: Mainland China

Performance at 12V Rated Voltage (Examples):

Rated Speed (RPM) No Load Current (mA) Load Speed (RPM) Load Current (mA) Load Torque (kg.cm) Output (W) Stall Torque (kg.cm) Stall Current (A) Reducer Ratio Size (mm) Weight (g)
977 46 781 300 0.11 1.25 0.55 1 4.4 15 99
463 46 370 300 0.23 1.25 1.1 1 9.28 17 99
55 46 44 300 1.95 1.25 9.7 1 78 23 99
8.6 46 6.8 300 12 1.25 60 1 500 27 99

Note: Full specifications for all RPM variants are available in Figure 2.

4. Safety Precautions

To ensure safe operation and prevent damage to the motor or injury, please observe the following safety guidelines:

  • Always ensure the power supply matches the motor's voltage requirements (6-24VDC).
  • Pay close attention to the polarity when connecting the motor and encoder power. Incorrect polarity can damage the encoder.
  • Avoid exceeding the maximum rated current and torque to prevent overheating and motor damage.
  • Do not operate the motor in wet or excessively dusty environments unless specifically designed for such conditions.
  • Ensure proper ventilation to prevent overheating, especially during prolonged operation or high loads.
  • Keep hands and loose clothing away from rotating parts during operation.
  • Disconnect power before performing any installation, wiring, or maintenance.

5. Installation and Wiring

5.1 Mounting the Motor

The JGA25-371 motor features standard mounting holes on the gearbox face. Refer to the dimension diagram in Figure 2 for precise measurements (M3*2 mounting holes, Ø4, Ø7, center distance 17mm). Ensure the motor is securely fastened to a stable surface to prevent vibration and misalignment.

JGA25-371 Geared Motor front view with output shaft
Figure 3: Motor Front View with Output Shaft

5.2 Wiring Connections

The motor is equipped with a 6-wire connector for both motor power and encoder feedback. Refer to the '接线方法' (Wiring Method) in Figure 2 for the color code and function of each wire. A visual representation of the encoder board and connected wires can be seen in Figures 4 and 5.

  • Red Wire: Motor Power + (Positive). Reversing polarity with the White wire controls motor direction.
  • White Wire: Motor Power - (Negative). Reversing polarity with the Red wire controls motor direction.
  • Blue Wire: Encoder Power + (Positive). Connect to a 3.3-5VDC power supply.
  • Black Wire: Encoder Power - (Negative). Connect to the ground of the 3.3-5VDC power supply.
  • Yellow Wire: Encoder Signal Feedback (Output A). Provides 11 signals per motor revolution.
  • Green Wire: Encoder Signal Feedback (Output B). Provides 11 signals per motor revolution.

CAUTION: Ensure correct polarity for the encoder power (Blue and Black wires). Incorrect connection (e.g., connecting 12V to the encoder) will damage the encoder.

JGA25-371 Geared Motor rear view with encoder board and connector
Figure 4: Motor Rear View with Encoder
JGA25-371 Geared Motor with connected wires
Figure 5: Motor with Wires Connected

6. Operation Guide

Once the motor is correctly installed and wired, follow these steps for operation:

  1. Power On: Apply the appropriate DC voltage (6-24V) to the Red (+) and White (-) motor power wires. The motor will begin to rotate.
  2. Direction Control: To reverse the motor's direction, swap the polarity of the Red and White wires.
  3. Speed Control: Motor speed can be controlled by varying the input voltage (within the 6-24V range) or by using Pulse Width Modulation (PWM) with a suitable motor driver.
  4. Encoder Feedback: Connect the Yellow and Green encoder signal wires to a microcontroller or a dedicated encoder interface. The encoder provides square wave signals (A and B phases) that can be used to determine rotational speed and direction, as well as precise position.
  5. Monitoring: Monitor the motor's temperature during operation. If it becomes excessively hot, reduce the load or operating time.

7. Maintenance and Storage

7.1 Maintenance

  • Cleaning: Keep the motor free from dust and debris. Use a soft, dry cloth or compressed air to clean the exterior. Avoid using liquids or solvents that could damage internal components.
  • Inspection: Periodically check wiring connections for looseness or damage. Inspect the output shaft for any signs of wear or bending.
  • Lubrication: The gearbox is typically pre-lubricated and sealed. Avoid disassembling the gearbox for lubrication unless you have specialized knowledge and tools, as this can void the warranty and introduce contaminants.

7.2 Storage

  • Store the motor in a cool, dry place, away from direct sunlight and corrosive substances.
  • Avoid storing in environments with high humidity or extreme temperature fluctuations.
  • Keep the motor in its original packaging or a protective container to prevent physical damage.

8. Troubleshooting

If you encounter issues with your JGA25-371 motor, refer to the table below for common problems and solutions:

Problem Possible Cause Solution
Motor does not rotate No power, incorrect wiring, motor jammed, faulty power supply Check power connections and voltage. Verify wiring polarity. Ensure no obstructions. Test power supply.
Motor rotates in wrong direction Incorrect motor power polarity Reverse the Red and White motor power wires.
Motor runs slowly or lacks torque Insufficient voltage, excessive load, worn brushes (over time) Increase voltage (within limits). Reduce load. Consider motor replacement if brushes are worn.
Encoder feedback is erratic or absent Incorrect encoder wiring, incorrect encoder power (voltage/polarity), faulty encoder Verify Blue/Black encoder power (3.3-5V) and polarity. Check Yellow/Green signal connections.
Motor overheats Excessive load, prolonged operation, insufficient ventilation Reduce load. Allow cooling periods. Ensure adequate airflow around the motor.

9. User Tips

No specific user tips were available from reviews or Q&A for this product at this time. However, general tips for geared motors include:

  • When designing your application, always consider the motor's stall torque and current to avoid damage.
  • For precise control, pair the Hall encoder with a microcontroller capable of reading quadrature signals.
  • Use appropriate motor drivers that can handle the motor's current draw, especially during startup or under load.

10. Disposal

When the motor reaches the end of its service life, dispose of it according to local regulations for electronic waste. Do not dispose of electrical components with general household waste.

11. Warranty and Support

For warranty information or technical support, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.