Introduction
The Godox iT30Pro is a compact and versatile camera flash speedlite designed for various camera systems, offering advanced features like TTL auto-exposure, High-Speed Sync (HSS), and a built-in 2.4GHz wireless X system. This manual provides detailed instructions for the safe and effective use of your iT30Pro flash.

Figure 1: Godox iT30Pro Flash Speedlite, Controller, Pouch, and USB-C Cable.
1. Setup
1.1 Package Contents
- iT30Pro Flash Unit
- iT30Pro Controller
- Protective Pouch
- USB-C Charging Cable
- TR TTL Hot Shoe Riser (if included with specific bundle)
1.2 Attaching to Camera
- Ensure both the camera and the iT30Pro controller are powered off.
- Slide the iT30Pro controller's hot shoe foot into your camera's hot shoe mount.
- Tighten the locking mechanism on the controller to secure it to the camera.
- If using the TR TTL Hot Shoe Riser, attach it to the camera's hot shoe first, then mount the iT30Pro controller onto the riser.

Figure 2: Godox TR TTL Hot Shoe Riser, used for compatibility or positioning.
1.3 Powering On/Off
Press and hold the power button on the iT30Pro controller to turn the unit on or off. The 2.8" full-color touchscreen will illuminate upon power-on.
2. Operating Instructions
2.1 Touchscreen Interface
The iT30Pro features a responsive 2.8" full-color touchscreen. Swipe through settings and adjust power with a tap. For tactile feedback, a traditional rotary dial is also available for fine-tuning flash output.

Figure 3: The iT30Pro controller's 2.8" full-color touchscreen and control buttons.
2.2 TTL Auto-Exposure Mode
In TTL (Through-The-Lens) mode, the iT30Pro meters light through your camera's lens in real-time. It instantly calculates the optimal flash output for perfectly exposed images. This mode allows you to focus on creativity rather than manual settings.

Figure 4: iT30Pro controller mounted on a camera, showing TTL auto-exposure in action.
2.3 Advanced Flash Features
- High-Speed Sync (HSS): Supports shutter speeds up to 1/8000s, allowing you to use flash with wide apertures in bright conditions. The "S" version for Sony cameras adds global-shutter flash sync up to 1/80000s.
- Front/Rear-Curtain Sync: Synchronize the flash with either the beginning or end of the shutter exposure for creative motion effects.
- Multi Mode: Fire a series of rapid flashes during a single exposure to capture multiple stages of movement.
- Flash Exposure Compensation (FEC): Adjust the flash output relative to the TTL metered value to fine-tune exposure.

Figure 5: iT30Pro controller showing flash exposure compensation settings.
2.4 Wireless Master & Receiver Modes
The iT30Pro features a built-in Godox 2.4GHz X system, allowing it to function as both a Master and a Receiver unit. This enables flexible and limitless multi-light setups. Pair it with a Godox X3 trigger or any other Godox 2.4GHz wireless flash unit.

Figure 6: Example of a wireless multi-light setup using the iT30Pro as part of the Godox 2.4GHz X system.
3. Maintenance
- Keep the flash unit and controller dry. Do not expose them to rain or moisture.
- Clean the unit with a soft, dry cloth. Do not use harsh chemicals or abrasive cleaners.
- Avoid strong impacts or dropping the unit.
- Store the unit in a cool, dry place when not in use, preferably in its protective pouch.
4. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Flash does not fire | Low battery; Incorrect camera settings; Flash not securely mounted; Flash in sleep mode. | Charge battery; Check camera flash settings (e.g., external flash enabled); Re-mount flash securely; Press any button to wake from sleep. |
| Flash output is inconsistent or incorrect | Incorrect flash mode; Flash exposure compensation set too high/low; Subject too close/far. | Verify flash mode (TTL/Manual); Adjust FEC; Ensure subject is within effective flash range. |
| Flash only fires once or intermittently at very close distances | Minimum working distance not met. | Ensure the flash is at least 0.5 meters (approximately 1.6 feet) away from the subject or synchronizer for consistent firing. |
| Wireless connection issues | Incorrect channel/group settings; Interference; Out of range. | Verify all units are on the same channel and group; Reduce distance between units; Change channel to avoid interference. |
5. Specifications
| Feature | Detail |
|---|---|
| Brand Name | Godox |
| Model | iT30Pro |
| Origin | Mainland China |
| Compatible Brands | Canon, Nikon, Olympus, Sony, Pentax, Fujifilm |
| Display | Yes (2.8" Full-Color Touchscreen) |
| TTL Support | Yes |
| High-Speed Sync (HSS) | Yes (up to 1/8000s; Sony "S" version up to 1/80000s) |
| Wireless System | Built-in Godox 2.4GHz X system (Master & Receiver) |
| Weight | Approx. 120g |
| Certification | CE |

Figure 7: The compact size of the iT30Pro, weighing approximately 120g.
6. User Tips
- Canon R7 Compatibility: Users have reported that TTL auto-exposure works perfectly with the Canon R7.
- Wireless Triggering: The iT30Pro can be triggered wirelessly from your camera to control other Godox flashes or modifiers like octaboxes, thanks to its built-in 2.4GHz X system and master/receiver capabilities.
- Minimum Distance: For consistent flash firing, especially when using a synchronizer or at very close range, ensure the flash unit is at least 0.5 meters (approximately 1.6 feet) away from the subject.
7. Warranty and Support
For warranty information and technical support, please refer to the official Godox website or contact your local distributor. Keep your proof of purchase for any warranty claims.