Glixal GY6 49cc 50cc 80cc 100cc CVK Carburetor Main Jet Set

Contents

Glixal GY6 CVK Carburetor Main Jet Set Instruction Manual

Model: GY6 49cc 50cc 80cc 100cc CVK Carburetor Main Jet Set

Brand: Glixal

1. Introduction

This manual provides detailed instructions for the installation, tuning, and maintenance of your Glixal GY6 CVK Carburetor Main Jet Set. This set includes 10 main jets with sizes #78, #80, #85, #87, #88, #90, #92, #94, #96, #98, designed for Keihin Round Style carburetors. Proper installation and tuning are crucial for optimal engine performance and longevity.

Glixal Main Jet Set (front view)
Figure 1: Glixal Main Jet Set (front view)
Glixal Main Jet Set (top view)
Figure 2: Glixal Main Jet Set (top view)

2. Warnings & Safety Instructions

Failure to follow these instructions can result in serious injury, engine damage, or fire.

2.1. Lean Condition Danger (Most Critical)

  • A "Lean" mixture (too much air, not enough fuel) causes extreme combustion temperatures.
  • Symptoms: Engine runs hotter than usual, loss of power at high RPM, "sputtering" under full throttle.
  • Consequence: Piston Melting, Cylinder Scoring, or Engine Seizure. This can happen in less than 5 minutes of riding at full throttle.
  • Action: If you suspect a lean condition, STOP IMMEDIATELY. Install a larger jet size.

2.2. Fire Hazard

  • Working on the carburetor involves fuel. Ensure the engine is COLD before starting any work.
  • Work in a well-ventilated area away from sparks or open flames.
  • Have a fire extinguisher nearby.

2.3. Small Parts Hazard

  • Jets are tiny and easily dropped into the carburetor throat or engine case.
  • Action: Use a magnetic tray. If a jet is dropped inside the carburetor, DO NOT START THE ENGINE. Disassemble and retrieve it. A loose metal jet entering the cylinder will destroy the engine.

2.4. Thread Damage

  • Brass jets are soft. Over-tightening can strip the threads in the carburetor holder or break the jet off inside.
  • Torque: Hand-tight plus a gentle snug with a screwdriver. Typically 0.5 – 0.8 N·m. Do not use excessive force.

2.5. Cleanliness

  • Any dirt or debris introduced during installation can block the tiny orifices, causing erratic running or engine damage. Clean hands and tools are essential.

3. Compatibility

This main jet set is designed for Keihin Round Style Main Jets with M4x0.70 thread size. It is compatible with various scooter and motorcycle models, particularly those equipped with GY6 49cc, 50cc, 80cc, and 100cc engines (e.g., 139QMB, 1P39QMA, 152QMI, 157QMJ).

Our parts may fit the following Brands:

  • Chinese Scooters, Mopeds, ATVs, Go Karts: NST, Peace, Roketa, SunL, Tank, TNG, Tomos Nitro, Vento, VIP, Baotian, Daelim, Romet, Kingway, ZumiCo, Motorbike.
  • European brands: Kymco, Piaggio, Vespa, Yamaha, Honda, Suzuki, PGO, SYM, PATRON, SAGITTA.
  • Other brands: BAOTIAN, JONWAY, QINGQI, SHENKE, ZNEN, LEIKE, WANGYE, LONGJIA, TIBEN, HUATIAN.

Important Note:

Please confirm the parts will fit your specific scooter/motorcycle model before installation. Some modified spare parts may require minor adjustments to your original motorcycle or engine.

Compatibility information and carburetor parts diagram
Figure 3: General compatibility information and a diagram of various carburetor parts.

4. Installation Instructions

4.1. Step 1: Preparation

  1. Cool Down: Ensure the engine is completely cold.
  2. Fuel Off: Turn the fuel petcock to "OFF".
  3. Access: Remove the seat and body panels to access the carburetor.
  4. Drain Bowl: Locate the drain screw at the bottom of the float bowl. Loosen it slightly to drain fuel into a container. Tighten back up once drained.
  5. Remove Float Bowl: Remove the 4 screws holding the float bowl to the main carburetor body. Carefully lower the bowl. Watch out for the float pin.

4.2. Step 2: Jet Replacement

  1. Locate Main Jet: Identify the main jet. It is typically located in the center tower (emulsion tube holder) or on a raised pedestal in the float bowl, depending on the specific carb model. It looks like a small brass bolt with a hole through the center.
  2. Remove Old Jet:
    • Use a properly fitting flathead screwdriver.
    • Turn Counter-Clockwise gently.
    • Caution: If it feels stuck, do not force it. Apply a drop of penetrating oil and wait. Forcing it can snap the jet head off.
  3. Verify Size: Check the number stamped on the side of the removed jet. Compare it with your new selection.
  4. Install New Jet:
    • Select the desired size from the kit.
    • Hand-thread the new jet Clockwise into the holder. Ensure it starts straight to avoid cross-threading.
    • Tighten: Snug it gently with the screwdriver. Do not overtighten. The seal is made by the tapered thread, not brute force.
  5. Inspect: Ensure the jet sits flush and straight. Verify the tiny hole is clear (look through it against a light source).

4.3. Step 3: Reassembly

  1. Clean Float Bowl: Wipe out any sediment from the float bowl. Ensure the float moves freely.
  2. Reinstall Bowl: Place the gasket (ensure it's seated correctly) and reattach the float bowl. Tighten the 4 screws in a star pattern evenly.
  3. Reconnect Fuel: Open the fuel petcock. Check for leaks around the bowl gasket and drain screw.

5. Tuning & Verification (CRITICAL)

This step determines if the engine survives.

  1. Initial Start: Start the engine. Let it idle. If it idles poorly, the issue might be the pilot jet (not the main jet), but ensure it doesn't stall immediately.
  2. Spark Plug Check (The "Chop Test"):
    • Ride the scooter at wide-open throttle (WOT) for a short distance (e.g., 100-200 meters).
    • IMMEDIATELY pull the clutch and kill the engine while still moving (do not let it idle back to the pit).
    • Remove the spark plug.
    • Analyze Color:
      • White / Blistered Electrode: TOO LEAN! Danger of engine destruction. Install a LARGER jet immediately.
      • Tan / Light Brown: PERFECT. Safe and optimal.
      • Black / Sooty: TOO RICH. Engine is wasting fuel and fouling. Install a SMALLER jet.
  3. Iterative Process: Tuning is a process. Change jets in increments of 2-4 sizes (e.g., 90 -> 92 -> 94) until you achieve a Tan color.
  4. Temperature Monitor: During test rides, frequently touch the engine casing (carefully). If it is significantly hotter than stock, you are likely running Lean. Stop and install a larger jet.

Note: Always refer to your scooter's official service manual for model-specific torque values and detailed tuning procedures.

6. Troubleshooting

Refer to the "Tuning & Verification" section (Section 5) for detailed steps on diagnosing and correcting common issues related to main jet sizing.

  • Engine runs hot, loss of power, sputtering (Lean Condition): Immediately install a larger main jet.
  • Engine wastes fuel, spark plug is black/sooty (Rich Condition): Install a smaller main jet.
  • Engine idles poorly after jet change: This may indicate an issue with the pilot jet, not the main jet. Ensure the main jet is correctly installed and then investigate pilot jet settings if idling issues persist.
  • Jets dropped into carburetor: DO NOT start the engine. Disassemble the carburetor and retrieve the jet to prevent severe engine damage.

7. Specifications

Attribute Value
Brand Name Glixal
Model Name GY6 49cc 50cc 60cc 100cc
Item Type Carburetor Main Jet Set
Material Copper
Condition 100% NEW
External Testing Certification ISO9001
Item Weight 0.03kg
Thread Size M4x0.70
Overall Length 7mm
Jet Sizes Included #78, #80, #85, #87, #88, #90, #92, #94, #96, #98 (10 pcs set)
Engine Model Compatibility 139QMB, 139QMA, 1P39QMA, 1P39QMB
Engine Type 4 stroke, Air Cooling
Dimensions of a single Glixal main jet
Figure 4: Dimensions of a single Glixal main jet (3.9mm thread length, 7mm overall length, 5mm head diameter).

8. User Tips

  • When tuning your carburetor, always start with a main jet size that is slightly larger than what you anticipate needing. Gradually work your way down in small increments. This approach helps prevent running too lean, which can cause severe engine damage.
  • Keep your work area clean and organized. The small size of the jets makes them easy to lose or contaminate.
  • Consider purchasing a complete set of jets to have a wider range for precise tuning, especially if you plan on future engine modifications.
Glixal main jets in clear plastic packaging
Figure 5: Glixal main jets as received in clear plastic packaging.

9. Frequently Asked Questions (FAQ)

Q: I changed my engine from 49cc to 60cc. What main jet size should I use?
A: When upgrading engine displacement, you will typically need a larger main jet to provide adequate fuel. However, the exact size depends on various factors like air intake, exhaust, and specific engine characteristics. It is crucial to follow the tuning process outlined in Section 5, starting with a slightly larger jet and performing spark plug chop tests to find the optimal size for your specific setup.

10. Warranty & Support

For any questions or support regarding your Glixal product, please contact the manufacturer or your retailer. Always refer to your scooter's official service manual for model-specific torque values and detailed tuning procedures.

Manufacturer: YIWU SHENGQI IMP&EXP CO.,LTD

Address: Unit 2, Building 71, Gongdatang No.1 District, Yiwu City, Zhejiang Province

Email: atmotorparts@outlook.com

EU Authorized Representative: SUCCESS COURIER SL

Address: CALLE RIO TORMES NUM. 1, PLANTA 1, DERECHA, OFICINA 3, Fuenlabrada, Madrid, 28947 Spain

Tel: 910602659

A user manual in PDF format is available for download: User manual (PDF)

© 2024 Glixal. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.