Kllisre DDR4 8GB 3200MHz/3600MHz Desktop Ram Memory

Contents

Kllisre DDR4 Desktop RAM User Manual

Model: DDR4 8GB 3200MHz/3600MHz Desktop Ram Memory

Brand: Kllisre

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Kllisre DDR4 Desktop RAM. Please read this guide carefully before installation to ensure proper functionality and to maximize the lifespan of your memory modules.

Kllisre DDR4 Desktop RAM is designed to enhance your computer's performance, offering high speeds and reliable operation for various applications, including gaming and professional tasks.

2. Safety Information

Warning: Always handle memory modules by the edges. Avoid touching the gold contacts or components on the circuit board. Static electricity can damage the memory, so use an anti-static wrist strap when handling components.

  • Ensure your computer is completely powered off and unplugged before handling any internal components.
  • Wear an anti-static wrist strap to prevent electrostatic discharge (ESD) damage.
  • Handle memory modules by their edges to avoid touching the gold contacts or integrated circuits.
  • Do not force the memory module into the slot; it should fit snugly with minimal pressure.

3. Installation Guide

Follow these steps to properly install your Kllisre DDR4 Desktop RAM:

3.1. Power Down the System

  1. Shut down your computer completely.
  2. Disconnect all power cables from the power supply unit.
  3. Press and hold the power button for a few seconds to discharge any residual power.

3.2. Open the Computer Case

  • Remove the side panel of your computer case to access the motherboard. Refer to your computer case manual for specific instructions.

3.3. Locate Memory Slots

  • Identify the DDR4 memory slots on your motherboard. These are typically long slots with clips on either end.
  • Consult your motherboard manual for the optimal slot population order. For dual-channel configurations, slots 2 and 4 are commonly recommended.
Motherboard with memory slots highlighted
Image: Example of a memory module and its dimensions (42mm height).

3.4. Release Retention Clips

  • Gently push the retention clips at both ends of the memory slot outward to open them.

3.5. Align the Memory Module

  • Hold the memory module by its edges.
  • Align the notch on the memory module with the key in the memory slot. This ensures correct orientation and prevents incorrect insertion.
Close-up of Kllisre DDR4 RAM module showing gold contacts and notch
Image: Close-up of the Kllisre DDR4 RAM module, highlighting the gold contacts and the alignment notch.

3.6. Install the Memory Module

  • Place the module into the slot and firmly press down on both ends until the retention clips snap into place automatically. You should hear a click.
Kllisre DDR4 RAM module with heat spreader
Image: Kllisre DDR4 RAM module featuring a heat spreader for efficient heat dissipation.

3.7. Repeat for Additional Modules

  • If installing multiple modules, repeat steps 3.4 to 3.6 for each module, following your motherboard's recommended population sequence for optimal performance (e.g., dual channel).

3.8. Close the System

  • Replace the computer case side panel.
  • Reconnect all power cables and peripherals.
  • Power on your system.

4. Operating Instructions

After physical installation, it is crucial to configure your system's BIOS/UEFI to ensure the memory operates at its advertised speed.

4.1. BIOS/UEFI Configuration (XMP/D.O.C.P.)

  • Upon powering on your computer, enter the system BIOS/UEFI (usually by pressing DEL, F2, or F10 during startup).
  • Verify that all installed memory is detected correctly.
  • Enable XMP (Extreme Memory Profile) for Intel platforms or D.O.C.P. (Direct Overclock Profile) for AMD platforms. This will allow the memory to run at its rated frequency (e.g., 3200MHz or 3600MHz) instead of the default J.E.D.E.C. speed (e.g., 2133MHz or 2400MHz).
  • Save changes and exit BIOS/UEFI.

Note: Memory products with a frequency of 3000MHz and higher are not using the J.E.D.E.C. standard, but rather the X.M.P. standard. Please check whether your motherboard and CPU support X.M.P. before purchasing. If the motherboard and CPU do not support X.M.P., the memory will only work at lower frequencies like 2666MHz/2400MHz.

5. Maintenance

Kllisre DDR4 RAM modules are designed for long-term reliability and generally require minimal maintenance. However, following these guidelines can help ensure optimal performance and longevity:

  • Keep System Clean: Regularly clean the interior of your computer case to prevent dust buildup, which can hinder airflow and heat dissipation.
  • Temperature Management: Ensure adequate cooling within your PC case. The integrated cooling fin on the RAM module helps with heat dissipation, but good case airflow is still important.
  • Firmware Updates: Keep your motherboard's BIOS/UEFI firmware updated. Manufacturers often release updates that improve memory compatibility and stability.
  • Avoid Physical Stress: Do not bend or apply excessive force to the memory modules.

6. Troubleshooting

If you encounter issues after installing your Kllisre DDR4 RAM, consider the following common solutions:

6.1. System Does Not Boot / Black Screen / Beeps

  • Reseat Modules: Power off the system, unplug it, and firmly reseat each memory module in its slot. Ensure the retention clips are fully engaged.
  • Check Compatibility: Verify that your motherboard and CPU officially support the installed DDR4 memory type and speed. Consult your motherboard's Qualified Vendor List (QVL).
  • Single Module Test: If you have multiple modules, try booting with only one module installed in the primary slot (refer to your motherboard manual). If it boots, test each module individually to identify a faulty one.
  • Clear CMOS: Reset your motherboard's CMOS settings (refer to your motherboard manual) to revert to default settings, which can sometimes resolve boot issues.

6.2. Memory Not Detected or Running at Lower Speed

  • BIOS/UEFI Check: Enter BIOS/UEFI and confirm that the system detects the correct amount of RAM.
  • Enable XMP/D.O.C.P.: As mentioned in the Operating Instructions, enable XMP (Intel) or D.O.C.P. (AMD) in your BIOS/UEFI settings to achieve the advertised frequency.
  • Motherboard Support: Ensure your motherboard supports the desired memory frequency. Some older motherboards or CPUs may have limitations.

6.3. System Instability / Blue Screen of Death (BSOD)

  • Run Memory Diagnostic: Use built-in Windows Memory Diagnostic or third-party tools like MemTest86 to check for memory errors.
  • Check XMP/D.O.C.P. Stability: If XMP/D.O.C.P. is enabled, try disabling it or manually setting a slightly lower frequency/looser timings in BIOS/UEFI to see if stability improves.
  • Voltage Settings: Ensure the memory voltage is set correctly (1.35V for this module). Incorrect voltage can lead to instability.

7. Specifications

FeatureSpecification
ModelDesktop Memory
Capacity8GB (available in 1Pcs or 2Pcs configurations)
Memory Speed (Frequency)3200 MHz, 3600 MHz
TypeDDR4
ApplicationDesktop
Memory Voltage1.35V
FeaturesUnbuffered
FunctionNon-ECC
Cooling FinYes
RGBNo
PackageYes
Chipset BrandHY, SEC, MIC, etc.
OriginMainland China
Video: Kllisre DDR4 RAM product showcase, demonstrating the module's design and features.

8. User Tips

  • Verify Compatibility: Before purchasing, always check your motherboard's QVL (Qualified Vendor List) and CPU specifications to ensure full compatibility with the chosen RAM frequency and capacity.
  • XMP/D.O.C.P. is Key: For frequencies above 2666MHz, enabling XMP (Intel) or D.O.C.P. (AMD) in your BIOS/UEFI is essential to achieve the advertised speeds. Without it, the RAM may default to a lower frequency.
  • Dual Channel Configuration: For optimal performance, install RAM modules in pairs according to your motherboard's manual to enable dual-channel mode.
  • Mixing RAM: While possible, mixing RAM modules of different brands, capacities, or speeds can sometimes lead to instability or force all modules to run at the lowest common speed/timings. It's generally recommended to use identical modules.
  • Troubleshooting Boot Issues: If your system doesn't boot after installation, try resetting CMOS or testing modules one by one.

9. Warranty and Support

Kllisre DDR4 Desktop RAM comes with a three-year warranty. For warranty claims or technical support, please contact your retailer or the manufacturer directly.

For additional guides and documents, you may refer to the official user manual PDF: User Manual (PDF).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.