Usongshine 17HS4401S

Contents

Usongshine Nema17 Stepper Motor 17HS4401S User Manual

Model: 17HS4401S | Brand: Usongshine

1. Introduction

This manual provides essential information for the safe and effective use of your Usongshine Nema17 Stepper Motor (Model 17HS4401S). This motor is designed for applications requiring precise motion control, such as 3D printers, CNC machines, and laser engraving equipment. Please read this manual thoroughly before installation and operation.

Five Nema17 stepper motors with connecting cables
Usongshine Nema17 Stepper Motors (5-pack)

2. Safety Warnings

  • Never disassemble or install the motor while powered on. Ensure all power is disconnected before handling.
  • Avoid use in humid environments to prevent electrical hazards and damage to the motor.
  • Wear insulated gloves during operation, especially when handling electrical connections.

3. Product Overview

The Usongshine 17HS4401S is a Nema17 hybrid stepper motor, known for its precise control, low noise, and high efficiency. It features a 1.8-degree step angle and a rated current of 1.5A per phase, making it suitable for various DIY and industrial automation projects.

Single Nema17 stepper motor with a cable and a ruler showing its length
Individual Nema17 Stepper Motor with cable

4. Specifications

CharacteristicSpecification
Model Number17HS4401S
Brand NameUsongshine
TypeHYBRID Stepper Motor
Phase2
Step Angle1.8° ± 0.09°
Rated VoltageDC 3.6V
Rated Current / PhaseDC 1.5A
Phase Resistance (20℃)2.4*(1±15%)Ω
Phase Inductance3.7*(1±20%)mH
Holding Torque≥420mN.m (0.4Nm)
Positioning Torque15 mN.m REF.
Rotating DirectionA-C B-D Clockwise
Maximum Slewing Rate≥1900 PPS
Maximum Starting Rate≥1500 PPS
Electrical StrengthAC600V/1mA/1S
Insulation Resistance≥100 MΩ (DC 500V)
Insulation ClassB
Temperature rise80°C Max (rated current, 2 phase on)
Shaft Diameter Options6.35mm (17HS4401-DuPont), 8mm (17HS4401S-XH2.54), 14mm (17HS4401S-DuPont)
CertificationCE, ROHS
Technical drawing showing motor dimensions and an electrical schematic
Motor Dimensions and Electrical Schematic

5. Setup & Wiring

Proper setup and wiring are crucial for the motor's performance and longevity.

5.1. Initial Setup

  1. Verify Wiring: Before applying power, double-check all wiring connections according to the provided diagrams.
  2. Controller Board: Connect the motor to your controller board, ensuring the input control signals match the board's instructions.

5.2. Wiring Diagrams

The motor typically comes with a 4-lead cable. Ensure correct connection to your control board based on the connector type (XH2.54 or DuPont).

Detailed wiring diagrams for XH2.54-4P and DuPont-4P connectors
Wiring for XH2.54-4P and DuPont-4P Connectors

6. Operation

After successful setup, you can begin operating the stepper motor.

  1. Power On: Apply power to your system.
  2. Observe Operation: After startup, observe the motor's operation for smoothness and any unusual noises.
  3. Precise Control: The motor enables accurate control of speed and position, making it ideal for precise movements in 3D printing or CNC applications.
Video demonstrating the stepper motor in operation on a 3D printer.

7. Maintenance

To ensure the longevity and optimal performance of your stepper motor, follow these maintenance guidelines:

  • Avoid Overload: Do not operate the motor under overload conditions, as this can lead to overheating and damage.
  • Minimize Start-Stop Cycles: Frequent starting and stopping can reduce motor lifespan. Optimize your control program to minimize unnecessary cycles.
  • Inspect Connections: Regularly inspect connection wires to ensure they are not loose or damaged. Secure any loose connections.
  • Motor Coil: The motor wire is made of pure copper enameled wire and features advanced winding technology for even arrangement, reducing temperature and deformation during long-term use.
  • Silicon Steel Rotor: The rotor uses international silicon steel material bearings and is coated with imported epoxy resin, cured at high temperature, to prevent jamming and ensure stability.
Close-up view of the motor coil
Motor Coil Detail
Close-up view of the silicon steel rotor
Silicon Steel Rotor Detail

8. Troubleshooting

If you encounter issues with your stepper motor, refer to the following common problems and solutions:

  • Motor does not rotate:
    • Check the power supply to ensure it is providing the correct voltage and current.
    • Verify the signal input from the controller board.
  • Motor vibration/jitter during operation:
    • Adjust the load on the motor. Excessive load can cause vibration.
    • Review and adjust the motor's parameter settings on your controller.
  • Excessive heating:
    • Inspect the heat dissipation system (if any) and ensure it is functioning correctly.
    • Check the load conditions; reduce load if it is too high.
    • Ensure the motor is not operating under continuous overload.

9. User Tips

  • This product is typically sold in packs of 5 motors.
  • The difference between models like HS4401 and HS4401S often lies in the type of connectors on the wires (e.g., XH2.54 vs. DuPont).
  • These motors are generally compatible with common 3D printers like Prusa I3 Steel and Tevo Tarantula.
  • The motor shaft is typically 5mm in diameter, with a recessed part, and approximately 20mm long.

10. Scope of Use

The Usongshine Nema17 Stepper Motor is versatile and can be used in a variety of applications:

  • 3D Printers: For precise movement of print heads and build platforms.
  • CNC Engraving Machines: Providing accurate positioning for carving and cutting.
  • Laser Engraving Machines: Ensuring precise control for detailed laser work.
  • Writing Machines: For automated drawing and writing tasks.
Examples of applications: CNC engraving machine and writing machine
Typical Applications: CNC Engraving Machine and Writing Machine

11. Warranty & Support

  • Warranty: This product comes with a one-year warranty from the date of purchase.
  • Technical Support: Free technical support is provided for any issues or questions you may have regarding the product. Please contact your retailer or Usongshine customer service for assistance.

12. Compliance

12.1. Disclaimer

⚠️ WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

13. Additional Resources

For a more detailed user manual and additional documentation, please refer to the official PDF document:

Download User Manual (PDF)

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.