1. Introduction
This manual provides essential information for the proper installation, operation, and maintenance of your Esky 000878 2.4GHZ Mixer Speed Gyro Control System (Model: EK2-0708). This unit is designed to provide stable and precise control for remote-controlled helicopters, integrating both mixing and gyro stabilization functions. Please read this manual thoroughly before use to ensure safe and optimal performance.
2. Product Overview
The Esky 000878 is a compact and integrated control unit for RC helicopters. It features a 2.4GHz receiver, a mixer for controlling multiple servos, and a speed gyro for flight stabilization. Its design is optimized for models such as the Lama V4 Hunter.



3. Specifications
| Feature | Detail |
|---|---|
| Model | 000878 EK2-0708 |
| Brand | Esky (RCMOY) |
| Frequency | 2.4GHz |
| Function | Mixer Speed Gyro Control System |
| Material | Composite Material |
| Recommended Age | 14+ years |
| Use | Vehicles & Remote Control Toys |
| Power Source | No Battery (Powered by RC system) |
| Batteries Included | No |
| Charger/Adapter Included | No |
| High-concerned chemical | None |
4. Setup and Installation
Proper installation is crucial for the performance and safety of your RC helicopter. Always refer to your helicopter's specific manual for wiring diagrams and mounting locations.
- Mounting: Securely mount the control system unit to the helicopter frame using double-sided foam tape or screws, ensuring it is level and free from vibrations. The orientation may be critical for gyro function; consult your helicopter's manual or the unit's markings if available.
- Power Connection: Connect the red power connector (visible in Figure 2) to the appropriate power output on your helicopter's Electronic Speed Controller (ESC) or power distribution board. Ensure correct polarity.
- Servo Connections: Connect your helicopter's servos (e.g., cyclic, tail rotor) to the corresponding output pins on the control system. The pins are typically labeled (e.g., AIL, ELE, RUD, THR) or numbered. Refer to your helicopter's manual for the correct servo assignments.
- Receiver Binding: This unit acts as a receiver. Follow the binding procedure for your 2.4GHz transmitter to link it with the control system. Typically, this involves powering on the receiver while holding a bind button (if present) or inserting a bind plug, then powering on the transmitter in bind mode.
- Initial Calibration: After binding, perform any necessary initial calibration steps as outlined in your helicopter's manual or the control system's specific instructions (if provided separately). This may include setting servo endpoints, sub-trims, and gyro direction.
5. Operation
Once installed and calibrated, the Esky 000878 system will manage the mixing of control inputs and provide gyro stabilization during flight.
- Pre-Flight Check: Before each flight, ensure all connections are secure, servos respond correctly to transmitter inputs, and the gyro is stabilizing in the correct direction.
- Gyro Sensitivity: If adjustable, gyro sensitivity can be fine-tuned via your transmitter or a dedicated pot on the unit (if present). Start with a moderate setting and adjust as needed for optimal stability without oscillation.
- Flight Modes: If your transmitter supports different flight modes (e.g., normal, idle-up), ensure they are configured correctly to work with the mixer and gyro settings.
6. Maintenance
To ensure the longevity and reliable performance of your control system, follow these maintenance guidelines:
- Keep Clean: Regularly inspect the unit for dust, dirt, or debris. Use a soft, dry brush or compressed air to gently clean the circuit board. Avoid using liquids.
- Check Connections: Periodically check all wiring connections for looseness, corrosion, or damage. Secure any loose connections.
- Avoid Moisture: Protect the unit from moisture and extreme temperatures. Store it in a dry, cool environment when not in use.
- Physical Inspection: Inspect the unit for any physical damage, such as cracked solder joints or damaged components. If damage is found, discontinue use and seek professional repair or replacement.
7. Troubleshooting
If you encounter issues with your Esky 000878 system, consider the following common problems and solutions:
- No Power/No Response:
- Check power connections and polarity.
- Ensure the ESC or power source is functioning correctly.
- Verify the transmitter is powered on and charged.
- Loss of Control/Intermittent Signal:
- Re-bind the receiver to the transmitter.
- Check for interference from other 2.4GHz devices.
- Ensure the receiver antenna is not damaged or obstructed.
- Unstable Flight/Oscillation:
- Adjust gyro sensitivity (reduce if oscillating, increase if too sluggish).
- Verify the gyro direction is correct (it should counter helicopter movement).
- Check for mechanical issues in the helicopter (e.g., loose blades, worn bearings).
- Servos Not Responding Correctly:
- Check servo connections to the control unit.
- Ensure servo endpoints and sub-trims are correctly set on the transmitter.
- Test servos individually if possible to rule out servo failure.
8. Warranty and Support
For warranty information, technical support, or service inquiries, please contact your original retailer or the manufacturer directly. Keep your proof of purchase for any warranty claims.