Dooya DC90 Single Channel Transmitter

Contents

Dooya DC90 Single Channel Transmitter User Manual

For Dooya RF433 Curtain Motors and Automatic Curtain Accessories

1. Introduction

The Dooya DC90 Single Channel Transmitter is a wireless remote control designed for operating Dooya RF433 curtain motors and automatic curtain accessories. This manual provides essential information for the safe and efficient use of your transmitter, including product overview, specifications, setup, operation, and maintenance.

2. Safety Information

  • Do not expose the transmitter to moisture or strike it, as this may affect its functionality and lifespan.
  • Ensure proper battery installation. Incorrect battery type or polarity can damage the device.
  • Keep batteries out of reach of children. Swallowing batteries can be dangerous.
  • Dispose of used batteries responsibly according to local regulations.

3. Product Overview

The DC90 transmitter features a simple, intuitive design for controlling your Dooya RF433 motor.

Dooya DC90 Single Channel Transmitter front view with specifications

Figure 1: Dooya DC90 Single Channel Transmitter

Image detailing the main buttons (on, pause, off) on the DC90 remote.

Figure 2: DC90 Button Layout (On, Pause, Off)

Image showing the DC90 series control system specification, including button functions for DC90, DC92(A), DC93/DC94.

Figure 3: DC90 Series Control System Button Functions

4. Specifications

AttributeValue
Model NumberDooya DC90 Single channel transmitter
Item TypeDooya DC90 Single channel transmitter for Dooya RF433 motors
Input Voltage3V (CR2430 battery)
RF Frequency433.05-434.79mhz
Transmit Power10 milliwatt
Transmit Distance200M in open air, 30M through 2 walls
Working Temperature-10 to 50 degrees Celsius
CompatibilityWorks for Dooya RF433 motors
BatteryCR2430 3VDC (not included)

5. Setup

5.1. Battery Installation

The DC90 transmitter requires a CR2430 3VDC battery (not included). Follow these steps to install the battery:

  1. Locate the battery compartment cover on the back of the transmitter.
  2. Slide the cover open to reveal the battery slot.
  3. Insert a CR2430 3VDC battery, ensuring the correct polarity (+/-).
  4. Slide the battery compartment cover back into place until it clicks securely.

Video 1: Unboxing and Battery Installation for DC90 Remote

Image showing the battery compartment of the DC90 remote, indicating CR2430 3V battery.

Figure 4: Battery Compartment (CR2430 3V)

5.2. Pairing with Dooya RF433 Motors/Receivers

The pairing process may vary slightly depending on your specific Dooya motor or receiver model. Always ensure the interval between different button presses is within 10 seconds for all settings, otherwise the system will restore to its original state.

5.2.1. Pairing with Matchable DC227/DC228 Receivers

Setup diagram for Matchable DC227/DC228 receivers.

Figure 5: Pairing with DC227/DC228 Receivers

  1. Switch on the receiver.
  2. Press the receiver's Programming key. The indicator will flash.
  3. Press the receiver's STOP button. The receiver indicator will long flash.
  4. Press the UP limit button of the transmitter.
  5. The indicator will flash and extinguish, indicating successful pairing.

5.2.2. Pairing with Matchable R Tubular Motor

Setup diagram for Matchable R Tubular Motor.

Figure 6: Pairing with R Tubular Motor

  1. Power on the motor. You will hear a long sound from the motor.
  2. Continuously press the setting button (P2) on the remote two times. You will hear a "didi" sound.
  3. Press the UP button on the remote one time. This completes the first code-setting, and the UP limit button will control the motor clockwise.
  4. Press the DOWN button on the remote one time. This completes the second code-setting, and the DOWN limit button will control the motor clockwise.

5.2.3. Pairing with RF433 Curtain Motor (General)

Pairing diagram for RF433 Curtain Motor with Remote.

Figure 7: Pairing with RF433 Curtain Motor

  1. Press Set Button 1 time on the motor/receiver.
  2. The red indicator on the motor/receiver will light up for about 10 seconds.
  3. Press P2 Button 1 Time on the remote.
  4. Press P2 Button 1 Time again on the remote.
  5. Press Open Button 1 time on the remote.
  6. Pairing is OK, and the indicator on the motor/receiver will turn off.

5.2.4. Pairing with RF433 Receiver of Wall Switch

Pairing diagram for RF433 receiver of wall switch with Remote.

Figure 8: Pairing with RF433 Wall Switch Receiver

  1. Power ON the wall switch receiver.
  2. Press the Set Button of the receiver 1 time. The indicator will light up for a long time.
  3. Press the UP Button of the remote control.
  4. Pairing is OK.

5.2.5. Pairing with Matchable DC136 Receiver

Setup diagram for Matchable DC136 receiver.

Figure 9: Pairing with DC136 Receiver

  1. Switch on the receiver.
  2. Press the receiver's Programming key. The green indicator will flash.
  3. Press the STOP button of the receiver. The receiver green indicator will long flash.
  4. Press the UP limit button of the transmitter.
  5. The green indicator will flash and extinguish, indicating successful pairing.

6. Operating Instructions

Once paired, use the buttons on your DC90 transmitter to control your Dooya RF433 motor:

  • UP Button (On): Activates the motor to move the curtain upwards or open it.
  • STOP/PAUSE Button: Stops the motor's current movement.
  • DOWN Button (Off): Activates the motor to move the curtain downwards or close it.
  • P+ / P- Buttons (for multi-channel models like DC93A/DC94A): Used to select different channels if your transmitter supports multiple channels. Press 'channel choose' button P- (number descending) or P+ (number increasing) to change the channel. Release your finger when the indicator moves to the suitable channel you select. All indicator lights flashing means all channels are effective (group control state).
  • Setting Button (P2): Used for programming and pairing procedures.

7. Maintenance

  • Cleaning: Wipe the transmitter with a soft, dry cloth. Do not use liquid cleaners or abrasive materials.
  • Battery Replacement: If you find the emission distance is obviously short or the remote becomes less sensitive, please change the battery. Refer to Section 5.1 for battery installation instructions.
  • Storage: Store the transmitter in a dry place, away from direct sunlight and extreme temperatures.

8. Troubleshooting

  • Remote not responding: Check if the battery is correctly installed and has sufficient power. Replace the battery if necessary.
  • Reduced transmission range: This could indicate a low battery. Replace the battery. Ensure there are no new obstructions (e.g., thick walls, metal objects) between the transmitter and the receiver.
  • Motor not pairing: Ensure you are following the correct pairing procedure for your specific motor/receiver model. The interval between button presses during setting must be within 10 seconds.
  • Motor responds erratically: Re-pair the remote with the motor/receiver. If the issue persists, check for interference from other RF devices.

9. User Tips

  • Always keep a spare CR2430 3VDC battery on hand for quick replacement.
  • If you have multiple Dooya RF433 motors, ensure you follow the correct pairing steps for each to avoid accidental control of other devices.
  • For optimal performance, try to maintain a clear line of sight between the remote and the motor/receiver, especially in environments with multiple walls.
  • If you are unsure about compatibility with a specific Dooya motor model (e.g., dm45e-50/12), consult the motor's manual or contact Dooya support.

10. Support

For further assistance or technical support, please contact your seller or refer to the official Dooya support channels.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.