Introduction
Congratulations on your purchase of the LoopTone 3-Speed Bluetooth Vinyl LP Record Player Turntable. This versatile audio system combines classic vinyl playback with modern connectivity options, including Bluetooth, USB/SD recording, FM/AM radio, and a cassette player. Enjoy your favorite music from various sources with high-quality sound through its built-in speakers or external audio systems.

Setup
- Unpacking: Carefully remove all components from the packaging. Retain packaging for future transport or storage.
- Placement: Place the unit on a stable, level surface away from direct sunlight, heat sources, and excessive dust or vibration.
- Power Connection: Connect the AC power cord to the unit's power input on the rear panel, then plug it into a suitable wall outlet (AC 110V~130V or AC 220V~240V, depending on your model).
- External Audio Output (Optional): To connect to an external amplifier or powered speakers, use RCA cables (not included) to connect the RCA output jacks on the rear of the unit to the corresponding input on your audio system.
- FM Antenna (Optional): For improved FM radio reception, connect an external FM antenna to the dedicated jack on the rear panel.

Operating Instructions
General Controls
- POWER Button: Press to turn the unit ON or OFF.
- VOLUME Knob: Rotate to adjust the audio output level.
- TUNING Knob: Rotate to tune into radio stations.
- Input Selector Switch: Use this switch to select between PHONO (turntable), USB/SD, TUNER (radio), and TAPE/AUX (cassette/auxiliary input) modes.

Turntable Operation (PHONO Mode)
- Lift the dust cover.
- Place a vinyl record on the turntable platter.
- Select the appropriate speed (33, 45, or 78 RPM) using the speed selector switch.
- Move the tone arm over the record.
- Gently lower the tone arm onto the record to begin playback.
- At the end of the record, the tone arm will automatically return to its rest.
Cassette Player Operation (TAPE/AUX Mode)
- Ensure the input selector switch is set to TAPE/AUX.
- Insert a cassette tape into the cassette slot on the side of the unit.
- Use the playback controls (Play, Stop, Fast Forward, Rewind) located near the cassette slot to operate the tape.

Radio Operation (TUNER Mode)
- Set the input selector switch to TUNER.
- Press the FM/AM/FM-ST button to cycle between FM, AM, and FM-Stereo modes.
- Rotate the TUNING knob to search for radio stations.
USB/SD Playback
- Insert a USB flash drive into the USB port or an SD card into the SD card slot.
- Set the input selector switch to USB/SD.
- The unit will automatically detect and begin playing compatible audio files.
- Use the playback control buttons (Play/Pause, Next/Previous, Stop) to manage your music.
Bluetooth Connectivity
- Set the input selector switch to TAPE/AUX.
- Long press the 'MODE' button until 'BT' appears on the display and you hear an audible tone, indicating Bluetooth pairing mode.
- On your mobile device, enable Bluetooth and search for available devices.
- Select 'LoopTone' from the list to connect. Once connected, you can play audio from your device through the turntable.
USB Encode (Recording)
This unit supports recording audio from vinyl, cassette, or radio directly to a connected USB drive or SD card. Refer to the 'REC' button on the control panel for recording functionality. Detailed instructions for recording are typically found in the full user manual.
Maintenance
- Cleaning the Unit: Use a soft, dry cloth to wipe the exterior of the unit. Do not use abrasive cleaners or solvents.
- Dust Cover: Keep the dust cover closed when not in use to protect the turntable and stylus from dust. Clean the dust cover with a soft, damp cloth.
- Stylus Care: The stylus (needle) is a delicate component. Handle with care. Clean the stylus periodically with a soft brush designed for stylus cleaning, brushing from back to front. Replace the stylus if sound quality deteriorates or if it appears damaged.
Troubleshooting
- No Power:
- Ensure the power cord is securely plugged into both the unit and a working electrical outlet.
- Check if the POWER button is pressed. - No Sound:
- Verify the VOLUME knob is turned up.
- Ensure the correct input mode (PHONO, USB/SD, TUNER, TAPE/AUX) is selected.
- If using external speakers, check their power and connections. - Poor Radio Reception:
- Adjust the position of the unit or the external FM antenna (if connected).
- Try tuning to a different station. - Bluetooth Not Connecting:
- Ensure the unit is in Bluetooth pairing mode ('BT' displayed, audible tone).
- Make sure Bluetooth is enabled on your mobile device.
- Try unpairing and re-pairing the device. - Record Skips or Distorted Sound:
- Ensure the record is clean and free of dust.
- Check if the stylus is clean and not damaged. Replace if necessary.
- Ensure the unit is on a stable, level surface to prevent vibrations.
Specifications
| Feature | Specification |
|---|---|
| Brand Name | LoopTone |
| Model Number | LT-LP001BK |
| Dimensions (W x H x D) | 32.5 x 14 x 30 cm (approx. 12.8 x 5.5 x 11.8 inches) |
| Stylus Type | Sapphire Tipped Ceramic Needle |
| Speeds | 33, 45, 78 RPM |
| Motor | Belt-driven |
| Output Connectors | RCA, USB, AUX-in; Headphone Jack |
| Functionality | AM/FM Radio, Cassette/USB/SD/MMC player, USB Encode, Aux-in, RCA |
| Voltage | AC 110V~130V & AC 220V~240V |
| Color | Black |

User Tips
- Radio Reception: Users have reported good tuner reception. If you experience issues, ensure your unit is not placed near other electronic devices that might cause interference.
- Recording Function: The unit supports recording from vinyl, cassette, or radio directly to a USB drive or SD card (USB Encode function). It does not record to CD.
Warranty and Support
For any questions, technical assistance, or warranty claims, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.