QYT KT-UV980Plus

Contents

QYT KT-980 Plus Mobile Radio User Manual

Model: KT-UV980Plus

Brand: QYT

Introduction

Thank you for choosing the QYT KT-980 Plus Mobile Radio. This device is a high-power, dual-band VHF/UHF transceiver designed for reliable communication in various environments, particularly suitable for vehicle installation. This manual will guide you through the proper setup, operation, maintenance, and troubleshooting of your new radio to ensure optimal performance and longevity.

Front view of the QYT KT-980 Plus mobile radio with microphone.
Figure 1: QYT KT-980 Plus Mobile Radio with Microphone

Package Contents

Before proceeding with installation, please verify that all the following items are included in your package:

  • Interphone host x1 (QYT KT-980 Plus Mobile Transceiver)
  • Microphone x1
  • Power cable x1 (Car Power Cable)
  • Screws & Fuse x1 set
  • Clip for Microphone x1
  • Bracket x1 (Mounting Bracket)
  • Instruction manual x1 (English User’s Manual)
Standard package contents including KT-980 Plus radio, microphone, power cable, screws & fuse, clip for microphone, and bracket.
Figure 2: Standard Package Contents

Installation

Antenna Installation

  1. Align the antenna with the interface on the radio unit.
  2. Rotate clockwise to tighten it.
  3. Attention: When twisting the antenna, hold the base of the antenna and rotate it. Do not shake the top of the antenna to avoid damaging the internal wiring.
Rear view of the radio unit with power cable and antenna connector.
Figure 3: Rear view showing antenna connector and power input

Power Cable Connection

Connect the provided power cable to the radio unit. Ensure a secure connection. The red wire is for positive (+) and the black wire is for negative (-).

Mounting the Radio

Use the provided bracket and screws to securely mount the radio in your desired location, typically in a vehicle. Ensure the mounting location allows for proper ventilation and access to controls.

Dimensions of the radio unit: 17 cm (length), 14 cm (width), 4 cm (height).
Figure 4: Radio Unit Dimensions

Basic Operation Guide

Charging Instructions

First Use: The new battery (if applicable, for handheld units or accessories) is usually in a low battery state. It is recommended to charge it for 4-6 hours when turned off for optimal performance.

Charging Method: Connect the charger to the power source. For walkie-talkies with charging docks/USB, insert the walkie-talkie (without shutting down) into the charging dock/USB for charging. Ensure good contact between the body and the charging pole.

Indicator Light Status: The indicator light is red when charging and turns green when fully charged.

Kind Reminder: Remove the battery promptly after it is fully charged, as overcharging can affect battery life.

Power On and Off

Press and hold the power button (usually integrated with the volume knob) for about 2-3 seconds. After turning on, the screen lights up and is accompanied by a prompt sound.

Adjust the Volume

Rotate the volume knob (usually integrated with the power button):

  • Rotate clockwise to increase the volume.
  • Rotate counterclockwise to decrease the volume.

Adjust the volume according to environmental noise; an appropriate level is better than the loudest setting.

Making a Call (Press and Speak Half Duplex Mode)

The walkie-talkie operates in a "press and speak" half-duplex mode, allowing only one party to speak at a time.

Launch (Speech):

  1. Press and hold the PTT (Push To Talk) button on the side of the microphone.
  2. Hold the microphone vertically, about 2.5-5 centimeters away from your mouth.
  3. Speak clearly at a normal pace.
  4. Release the PTT button after speaking.

Reception (Listening):

After releasing the PTT button, the walkie-talkie automatically enters the receiving mode. You will then hear the other person's speech.

Telephone Etiquette:

  • Pause slightly before speaking to avoid interrupting.
  • After finishing your message, it is good practice to add "Done" or "Over" to inform the other party that you have finished speaking and can release the button.
Video 1: Product demonstration showing the radio unit and microphone, including frequency input on the microphone keypad.

Advanced Features

1. One-Click Frequency Matching/Copying:

Some walkie-talkies support frequency duplication. To use this function:

  • Bring two walkie-talkies closer together.
  • On the transmitting radio: Enter the menu and select "Copy" or "CLONE" mode.
  • On the receiving radio: Also enter replication mode.
  • Press the PTT button on the transmitting radio, and the data will be automatically transmitted.

2. Scanning Function:

When you are unsure which channel the other party is on, press the SCAN button. The walkie-talkie will automatically cycle to detect signals on the current channel and stop automatically when a signal is found.

3. Voice Control Function (VOX):

After enabling the VOX (voice control) function, you do not need to press the PTT button. You can directly speak into the walkie-talkie to transmit, which is suitable for use when both hands are occupied.

Close-up of the radio and microphone showing eye-friendly night illumination on the display and keypad.
Figure 5: Eye-friendly night illumination on display and keypad

Specifications

FeatureSpecification
Brand NameQYT
Model NumberKT-UV980Plus
Walkie Talkie TypeCar
Frequency RangeVHF: 136-174MHz / UHF: 400-480MHz
Output Power (W)>50W (High >=50 Watt, Low 25 Watt)
Maximum Range>50km
Storage Channel200
Channel Spacing25KHz/20KHz/12.5KHz
Frequency Stability2.5ppm
Operating Temperature-20℃ to +60℃
Operating Voltage13.8V DC ±15%
Weight (with bracket)1.8Kg
MaterialPlastic
Is DisplayYes
Waterproof / Water-ResistantNo
Rechargeable Battery IncludedYes (for microphone, not main unit)
PTT ID SettingYes
Auto LockYes
Remote StunYes
Remote KillYes
CertificationCE

Note: Due to national radio regulations, the product label may indicate <=50W, but the actual transmitting power remains the original 75W for VHF and 55W for UHF. The high transmitting power requires a 200W high power antenna for optimal performance.

Diagram illustrating U&V Dual Band Transmitting Power (VHF: 136-174MHz 75W, UHF: 400-480MHz 55W). Note: Requires 200W high power antenna.
Figure 6: U&V Dual Band Transmitting Power Diagram

Daily Maintenance

Cleaning

If the radio body becomes dirty, wipe it with a soft cloth dampened with a neutral detergent. Do not use alcohol, spray, or corrosive detergents, as these can corrode the shell.

Storage

When not in use for a long time, turn off the walkie-talkie and store it in a dry and cool place.

Common Troubleshooting

Problem PhenomenonPossible Causes and Solutions
Unable to power onThe battery is fully discharged (please charge); Poor battery contact (remove and reinstall).
Too close call distance/noiseLow battery level (please charge); Located in a dead corner of the building (change position); The antenna is not tightened.
The other party cannot hear my voiceDid not hold down the PTT key while speaking; The microphone is too far from the mouth.
The charging indicator light is not onThe charger is not plugged in properly; Poor contact between the body and the charging dock; The battery is damaged.

Safety and Usage Precautions

To extend the lifespan of the equipment and ensure safety, please note the following:

Prohibited Actions:

  • Do not hold down the PTT button for a long time to transmit. Continuous transmission for a long time (such as more than 1 minute) can cause the body to heat up and may damage the amplifier.
  • Do not hold the antenna or mobile walkie-talkie: This can cause poor antenna contact or even damage to internal components.
  • Do not replace batteries in flammable and explosive places, such as gas stations or chemical plants, as electric sparks may cause explosions.

If the power of the device you purchase exceeds 0.5W, according to China's Radio Management Regulations, you may need to apply for a radio station license when using it, otherwise you may face fines. Please consult your local radio management department.

User Tips

  • For optimal range and clarity, ensure your antenna is correctly installed and positioned away from obstructions.
  • Regularly check all cable connections for tightness, especially the power and antenna cables, to prevent signal loss or power interruptions.
  • When operating in high-interference areas, try adjusting the squelch level (SQL) to filter out unwanted noise.

Support

If you still have any questions or require further assistance, please contact our customer service at 1669036781@qq.com.

For additional documentation, a user manual PDF is available. Please refer to the seller's product page for the direct link to the PDF document.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.