1. Introduction
This manual provides detailed instructions for the safe and effective use of your RICHMETERS RM102 Digital Multimeter. This device is designed for measuring AC/DC voltage, AC/DC current, resistance, capacitance, frequency, diode, continuity, and temperature. It features stable performance, high reliability, and a clear digital display, making it an essential tool for electrical DIY projects and professional use.

2. Safety Information
To ensure safe operation and service of the meter, follow these safety precautions:
- Always ensure the correct function and range are selected before making measurements.
- Do not exceed the maximum input values for any range.
- Disconnect the test leads from the circuit before changing functions or ranges.
- Be extremely careful when working with voltages above 30V AC RMS, 42V peak, or 60V DC. These voltages pose a shock hazard.
- Always disconnect circuit power and discharge all high-voltage capacitors before measuring resistance, continuity, or capacitance.
- Replace the battery immediately when the low battery indicator appears to ensure accurate readings.
- Do not operate the meter if it appears damaged or if the case is open.
- Use only the specified fuses for replacement.
3. Product Overview
The RM102 Digital Multimeter features a clear LCD display, a rotary switch for function selection, and input jacks for test leads. The device is compact and designed for ease of use.

3.1. Display Icons and Functions
The LCD display shows measurement values and various icons indicating the selected function and status. Refer to the image below for a description of common icons:

- V~: AC Voltage measurement
- V=: DC Voltage measurement
- A~: AC Current measurement
- A=: DC Current measurement
- ℃/℉: Temperature measurement (Celsius/Fahrenheit)
- Backlight icon: Display backlight active
- Ω: Resistance measurement
- Hz: Frequency measurement
- Diode icon: Diode test
- µF: Capacitance measurement
- H: Data Hold function
- Continuity icon: Continuity test (Buzzer)
4. Specifications
| Feature | Specification |
|---|---|
| Brand Name | KKMOON |
| Model Number | RM102 |
| Display Type | Digital Display |
| Operating Mode | Manual Range |
| DIY Supplies | Electrical |
| Operating Temperature | 0 - 40 ℃ |
| Measuring Voltage Range (DC) | 6V / 60V / 600V / 700V |
| Measuring Voltage Range (AC) | 6V / 60V / 600V / 700V |
| Measuring Current Range (AC) | 600uA/6000uA/60mA/600mA/10A |
| Measuring Resistance Range | 600 ohm /6k ohm /60k ohm /600kohm/6Mohm/60Mohm |
| Measuring Capacitance Range | 10nF/100nF/1uF/10uF/100uF/1000uF/10000uF |
| Measuring Inductance Range | ---- |
| Battery Included | Yes (Requires 2x AAA batteries for operation) |
| Dimensions | 13 * 6.5 * 3.2cm / 5.1 * 2.56 * 1.26in |
| Weight | 0.209 kg |
| Certification | NONE |
| Origin | Mainland China |
5. Setup
5.1. Battery Installation
The RM102 Multimeter requires two AAA batteries for operation. To install or replace batteries:
- Ensure the multimeter is turned OFF and test leads are disconnected.
- Locate the battery compartment cover on the back of the device.
- Unscrew the retaining screw(s) and remove the cover.
- Insert two AAA batteries, observing the correct polarity (+ and -).
- Replace the battery compartment cover and secure it with the screw(s).
5.2. Connecting Test Leads
Always connect the black test lead to the 'COM' (Common) jack. Connect the red test lead to the appropriate input jack based on the measurement you intend to make:
- For Voltage, Resistance, Capacitance, Frequency, Diode, and Continuity measurements: Connect the red lead to the 'VΩHz' jack.
- For Current measurements (up to 600mA): Connect the red lead to the 'mA' jack.
- For High Current measurements (up to 10A): Connect the red lead to the '10A' jack.
6. Operating Instructions
6.1. General Operation
- Power On/Off: Rotate the central switch from 'OFF' to any desired function to power on. Rotate back to 'OFF' to power off.
- Auto Power Off: The multimeter will automatically power off after a period of inactivity to conserve battery life.
- Backlight: Press the 'HOLD/✨' button briefly to turn the display backlight on or off. The backlight typically turns off automatically after 8-10 seconds.
- Data Hold: Press and hold the 'HOLD/✨' button to freeze the current reading on the display. Press again to release.
6.2. Measurement Functions
Follow these steps for specific measurements:
- Measuring DC/AC Voltage (V= / V~):
- Turn the rotary switch to the 'V=' (DC Voltage) or 'V~' (AC Voltage) position.
- Connect the black test lead to the 'COM' jack and the red test lead to the 'VΩHz' jack.
- Connect the test leads in parallel across the component or circuit to be measured.
- Read the voltage value on the display.
- Measuring DC/AC Current (A= / A~):
- Turn the rotary switch to the 'A=' (DC Current) or 'A~' (AC Current) position.
- Connect the black test lead to the 'COM' jack. For currents up to 600mA, connect the red lead to the 'mA' jack. For currents up to 10A, connect the red lead to the '10A' jack.
- Disconnect power to the circuit. Open the circuit where the current is to be measured.
- Connect the multimeter in series with the circuit.
- Apply power to the circuit and read the current value on the display.
- Measuring Resistance (Ω):
- Turn the rotary switch to the 'Ω' (Resistance) position.
- Connect the black test lead to the 'COM' jack and the red test lead to the 'VΩHz' jack.
- Ensure the circuit is de-energized and all capacitors are discharged.
- Connect the test leads across the component to be measured.
- Read the resistance value on the display.
- Measuring Capacitance (µF):
- Turn the rotary switch to the 'Ω' position.
- Press the 'FUNC' (yellow) button to cycle through functions until 'µF' is displayed.
- Connect the black test lead to the 'COM' jack and the red test lead to the 'VΩHz' jack.
- Ensure the capacitor is fully discharged before connecting the leads.
- Connect the test leads across the capacitor.
- Read the capacitance value on the display.
- Diode Test (Diode icon):
- Turn the rotary switch to the 'Diode' position.
- Connect the black test lead to the 'COM' jack and the red test lead to the 'VΩHz' jack.
- Connect the red lead to the anode and the black lead to the cathode of the diode.
- The display will show the forward voltage drop. Reverse the leads; the display should show 'OL' (Open Loop) for a good diode.
- Continuity Test (Buzzer icon):
- Turn the rotary switch to the 'Buzzer' position.
- Connect the black test lead to the 'COM' jack and the red test lead to the 'VΩHz' jack.
- Connect the test leads across the circuit or component.
- If the resistance is below approximately 50Ω, the buzzer will sound, indicating continuity.
- Measuring Frequency (Hz):
- Turn the rotary switch to the 'Hz' position.
- Connect the black test lead to the 'COM' jack and the red test lead to the 'VΩHz' jack.
- Connect the test leads across the signal source.
- Read the frequency value on the display.
- Measuring Temperature (℃/℉) - RM102 Only:
- Turn the rotary switch to the '℃/℉' position.
- Connect the thermocouple (included with RM102) to the 'VΩHz' and 'COM' jacks, observing polarity if specified by the thermocouple.
- Place the thermocouple probe on or near the object whose temperature is to be measured.
- Read the temperature value on the display.
7. Maintenance
7.1. Cleaning
Wipe the case with a damp cloth and mild detergent. Do not use abrasives or solvents. Keep the input terminals clean and free from dust or debris.
7.2. Battery Replacement
When the battery symbol appears on the LCD, the batteries must be replaced. Refer to Section 5.1 for instructions.
7.3. Fuse Replacement
If the current measurement function stops working, the fuse may be blown. Replace with a fuse of the specified type and rating:
- For mA input: FUSED 600mA MAX
- For 10A input: FUSED 10A MAX
To replace a fuse, open the battery compartment as described in Section 5.1, then carefully remove the old fuse and insert a new one of the correct specification.
8. Troubleshooting
- No display after power on: Check if the batteries are correctly installed and have sufficient charge. Replace if necessary.
- Incorrect readings: Verify that the correct function and range are selected for the measurement. Ensure test leads are properly connected to the correct input jacks and making good contact with the circuit.
- Backlight turns off quickly: This is normal behavior designed to conserve battery life. Press the backlight button again if continuous illumination is needed.
- Continuity buzzer delay: A slight delay (around 0.5 seconds) in the continuity buzzer is normal for this model.
- Capacitance measurement issues: Ensure the capacitor is fully discharged before measurement. If still inaccurate, check the test leads for damage.
9. User Tips
- The RM102 model includes a temperature measurement function and comes with a thermocouple probe.
- For measuring capacitance, first switch the rotary dial to the resistance (Ω) mode, then press the yellow 'FUNC' button to cycle until the capacitance (µF) icon appears on the display.
- The multimeter features an auto-off function to save battery power if left idle for an extended period.
- While the multimeter is precise for its price range, for highly critical voltage measurements, consider its manual range operation.
10. Warranty and Support
For any questions, technical assistance, or warranty claims, please contact the manufacturer or your point of purchase. Keep your purchase receipt as proof of purchase.
11. Disposal
This product contains electronic components and batteries. Do not dispose of it with household waste. Please follow local regulations for the proper disposal of electronic waste and batteries to prevent environmental pollution and ensure the recycling of materials.