Godox CT-16 Transmitter

Contents

Godox CT-16 Wireless Flash Trigger Transmitter Instruction Manual

Model: CT-16 Transmitter

1. Introduction

The Godox CT-16 Wireless Flash Trigger Transmitter is designed to wirelessly trigger studio flashes, speedlights, and other compatible flash units. It operates on a 433MHz frequency and offers 16 selectable channels, providing reliable synchronization for your photography needs. This manual provides detailed instructions for the proper setup, operation, and maintenance of your CT-16 transmitter.

Front view of the Godox CT-16 Wireless Flash Trigger Transmitter
Figure 1: Godox CT-16 Transmitter Front View

2. What's in the Box

  • Godox CT-16 Transmitter × 1
Image showing the contents of the box, which is one Godox CT-16 Transmitter.
Figure 2: Package Contents

3. Setup

  1. Battery Installation: The CT-16 transmitter typically uses a 12V 23A battery. Open the battery compartment (usually on the side or back) and insert the battery, ensuring correct polarity.
  2. Channel Selection: Locate the 16-channel DIP switches on the bottom of the transmitter. Use a small tool (like a pen tip) to set the desired channel. Ensure that the transmitter and your compatible receiver (sold separately) are set to the exact same channel for proper communication.
Bottom view of the Godox CT-16 Transmitter showing the 16-channel DIP switches and the hot shoe mount.
Figure 3: Channel Selection DIP Switches and Hot Shoe
  1. Mounting to Camera: Slide the transmitter onto your camera's hot shoe. Ensure it is securely fastened.
  2. Connecting to Flash (Optional): If your camera does not have a hot shoe or you prefer a wired connection, connect the transmitter to your camera's PC sync port using a PC sync cable (not included). The PC sync port is located on the side of the transmitter.
Side view of the Godox CT-16 Transmitter showing the PC sync port.
Figure 4: PC Sync Port

4. Operating Instructions

  1. Power On: Ensure the battery is correctly installed. The transmitter does not have a separate power switch; it is activated when mounted on the camera's hot shoe or when a signal is sent.
  2. Test Firing: Press the test button on the transmitter to manually fire the connected flash unit. A small LED indicator on the transmitter will light up to confirm transmission.
  3. Automatic Triggering: When mounted on your camera's hot shoe, the transmitter will automatically send a trigger signal to the receiver (connected to your flash) when you press your camera's shutter button.
  4. Synchronization: The CT-16 provides reliable synchronization for most cameras and flash units. Ensure your camera's shutter speed is set within its flash sync speed limits (typically 1/200s or 1/250s, consult your camera manual).

5. Maintenance

  • Cleaning: Use a soft, dry cloth to clean the exterior of the transmitter. Do not use abrasive cleaners or solvents.
  • Storage: When not in use for extended periods, remove the battery to prevent leakage. Store the transmitter in a cool, dry place away from direct sunlight and extreme temperatures.
  • Handling: Avoid dropping the unit or subjecting it to strong impacts.

6. Troubleshooting

  • Flash not firing:
    • Ensure the transmitter and receiver are set to the same channel.
    • Check if the battery in the transmitter is fresh and correctly installed.
    • Verify that the receiver is properly connected to the flash unit and has power.
    • Confirm the transmitter is securely mounted on the camera's hot shoe or connected via PC sync cable.
  • Inconsistent firing:
    • Check for potential radio interference in the environment.
    • Ensure the distance between the transmitter and receiver is within the effective range.
    • Replace the battery in the transmitter if it's low.
  • Flash sync issues (e.g., black bar in photos):
    • Adjust your camera's shutter speed to be at or below its maximum flash sync speed.

7. Specifications

FeatureSpecification
Model NumberCT-16 Transmitter
TypeWireless Flash Trigger
Channels16
Compatible BrandsCanon, Nikon, Pentax, Olympus
Dimensions (L x W x H)6 cm x 4 cm x 3.5 cm
WeightApproximately 0.15 kg
CertificationCE
OriginMainland China
Image showing the dimensions of the Godox CT-16 Transmitter: 6cm length, 4cm width, 3.5cm height.
Figure 5: Transmitter Dimensions

8. User Tips

  • Cross-Brand Compatibility: Users have reported successful compatibility with other flash trigger brands like Neewer, provided the channels are matched.
  • Versatile Use: This trigger is suitable for various Godox flash units, including the Godox Smart 300 DSI and TT600, as well as other speedlights.
  • Camera Compatibility: Works well with a range of Nikon cameras, including the Nikon D7500, and other compatible Canon, Pentax, and Olympus models.

9. Frequently Asked Questions (FAQ)

Q: What type of flash trigger is the Godox CT-16?
A: It is a wireless flash trigger.
Q: Is the CT-16 compatible with the Godox TT600 flash?
A: Yes, the CT-16 transmitter is compatible with the Godox TT600 flash.
Q: Can this transmitter be used with a Nikon D7500 camera?
A: Yes, it is compatible with Nikon D7500 cameras.
Q: Does it work with the Godox TT520?
A: Yes, the CT-16 is compatible with the TT520 flash unit.

10. Warranty and Support

For warranty information and technical support, please refer to the official Godox website or contact your authorized dealer. Keep your purchase receipt as proof of purchase for any warranty claims.

© 2023 Godox. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.