Introduction
Thank you for your purchase of the Godox X1T-C TTL wireless flash trigger. This TTL wireless flash trigger is designed for Canon cameras. It can directly control flashes that have built-in Godox wireless X system (e.g., TT685F, V860IIF, AD360II, AD600, AD600M, QuickerII, etc.). For flashes without Godox wireless X system (e.g., V860, V850, AD360), an XTR-16 or XTR-16S receiver can be used in combination to achieve manual flash control. Featuring multi-channel triggering, stable signal transmission, and sensitive reaction, it offers photographers unparalleled flexibility and control over their strobist setups. The X1T-C can also connect to cameras with PC sync sockets. It supports high-speed sync function and a maximum flash synchronization speed of up to 1/8000s*.
*1/8000s is achievable when the camera has a maximum camera shutter speed of 1/8000s.
Note: This manual has been adapted from the Godox X1T-F (Fujifilm) manual. While general operation is similar, specific Canon-related functions and compatibility details should be verified with the official Godox X1T-C documentation.

Safety Warnings
- Do not disassemble. Should repairs become necessary, this product must be sent to an authorized maintenance center.
- Always keep this product dry. Do not use in rain or in damp conditions.
- Keep out of reach of children.
- Do not use the flash unit in the presence of flammable gas. In certain circumstances, please pay attention to the relevant warnings.
- Do not leave or store the product if the ambient temperature reads over 50℃.
- Turn off the flash trigger immediately in the event of malfunction.
- Observe precautions when handling batteries:
- Use only batteries listed in this manual. Do not use old and new batteries or batteries of different types at the same time.
- Read and follow all warnings and instructions provided by the manufacturer.
- Batteries cannot be short-circuited or disassembled.
- Do not put batteries into a fire or apply direct heat to them.
- Do not attempt to insert batteries upside down or backwards.
- Batteries are prone to leakage when fully discharged. To avoid damage to the product, be sure to remove batteries when the product is not used for a long time or when batteries run out of charge.
- Should liquid from the batteries come into contact with skin or clothing, rinse immediately with fresh water.
Names of Parts
Transmitter Body

- TEST Trigger Button: Initiates a test flash.
- AF Assist Beam Switch: Controls the AF assist beam output (ON/OFF).
- Power Switch: Turns the unit ON/OFF.
- Status Indicator Lamp: Red LED lamp indicates status.
- CH/OK Channel Setting Button: Used for channel selection and confirmation.
- GR Group Setting Button: Used for group selection.
- Select Dial: Used to adjust values.
- MODE Mode Selection Button: Used to select flash modes.
- LCD Panel: Displays settings and information.
- Battery Compartment: Holds two AA batteries.
- Micro USB Port: For firmware upgrades.
- PC Sync Socket: For input and output connections.
- Hot Shoe Camera Connection: Mounts the transmitter to the camera's hot shoe.
- Hot Shoe Speedlite Connection: For mounting a speedlite on top of the transmitter.
Battery
Installing Batteries
Slide the battery compartment lid of the transmitter and insert two AA batteries (sold separately) according to the polarity indicators.
Low Battery Level Indication
When the battery power (2 AA batteries <2.4V) gets low, the Status Indicator Lamp blinks quickly (blink cycle=0.5s). Please replace new batteries, as low power leads to no flash or flash missing in case of long distance.
Setup and Operation
The X1T-C flash trigger features the following functions:
1. As a Wireless Flash Trigger
- Mount the transmitter on camera hotshoe and turn it on before turning on the camera.
- Set the transmitter and the receiver to the same channel by pressing the CH/OK Channel Setting Button.
- Press the camera shutter button, and the flash will be triggered simultaneously. The Status Indicator Lamp of the transmitter turns red.
2. As a Wireless Flash Trigger with PC Sync Socket
- Set the transmitter end and receiver end to the same channel and group.
- The transmitter will control the flash on the receiver end to fire via using the PC Sync Socket as input by default.
- Press the camera shutter and use the PC Sync Socket's signal to control the flash.
- The PC Sync Socket can also be set as output. Long press the CH/OK Button of the transmitter until <Fn> is displayed on the panel. Then, set the value of C.Fn-03 to 'ou', and the PC Sync Socket is under output mode.
Setting the Transmitter
- Power Switch: Slide the Power Switch to ON. The device is on and the Status Indicator Lamp will not blink. Note: In order to avoid power consumption, turn off the transmitter when not in use.
- Power Switch of AF Assist Beam: Slide the power switch to ON, and the AF lighting is allowed to output. When the camera cannot focus, the AF assist beam will turn on; when the camera can focus, the AF assist beam will turn off.
- Channel Settings:
- Short press the <CH/OK> Button until the channel amount blinks.
- Turn the Select Dial to choose the appropriate channel. Press the <CH/OK> Button again to confirm the setting.
- This flash trigger contains 32 channels which can be changed from 1 to 32. Set the transmitter and the receiver to the same channel before usage.
- Mode Settings:
- Short press the <GR> Button and the selected group will blink. Click to choose downwardly and double-click to choose upwardly.
- Short press the <MODE> Button and the selected groups' modes will be changed by the order of TTL/M/-- (-- represents OFF, which means that the current group will not fire flashes in this mode).
- Group POWER / FEC Settings:
- Short press the <GR> Button and the selected group will blink. Click to choose downwardly and double-click to choose upwardly.
- Turn the Select Dial to change the power or flash exposure compensation settings. When the current group is in the M mode, the power output value is changeable from 1/1 full power to Min. [Note 1] power in 0.3 stop increments. When the current group is in the TTL mode, the FEC amount is changeable from -3 to 3 in 0.3 stop increments. When the current group is in the -- mode (flash off), the amounts will not change.
- Short press the <CH/OK> Button again to confirm the setting.
Note 1: Min. refers to the minimum power output value that can be set in M/Multi mode. 1/128 or 1/256 can be set according to C.Fn-05. The minimum power output value is 1/128 and cannot be set to 1/256 for most camera flashes. However, the value can change to 1/256 when using in combination with Godox strong power flashes e.g. AD600, etc.
- Multi Flash Group ON/OFF Settings:
- Open the multi flash in the C.Fn Custom Functions (set C.Fn-04 as 1).
- Short press the <GR> button to select the group. Click to choose downwardly and double-click to choose upwardly.
- Short press the <MODE> Button to change the mode of selected group.
- The current group's mode will be changed by the order of on/-- (-- represents OFF, which means that the current group will not fire flashes in this mode).
- Multi Flash Parameter Setting:
- Enter into multi flash mode before setting.
- Press the <MODE> Button to enter multi flash parameter setting menu.
- Then, P (output value), T (flash times) and H (flash frequency) will be displayed on the LCD panel.
- Short press the <GR> Button to choose the settings. Turn the Select Dial to change the blinking setting amount. Continue to press the <GR> Button until all the amounts are set. Then, short press the <MODE> Button to exit.
Note: As flash times are restricted by flash output value and flash frequency, it might get automatic adjustment. The times that transported to the receiver end are setting times, which is not related to the camera's shutter setting. To guarantee the normal times of stroboscopic times, please use the formula below to calculate the shutter speed: Number of Flashes/Firing Frequency=Shutter Speed.
- Group Settings:
- Long press the <GR> Button to set all the groups that in the same modes simultaneously.
- The settings of the groups which are in the same mode with the current group will blink. Turn the Select Dial to change the settings.
- If the current group is in the M mode, all the other groups which are in the M mode will change their power output value simultaneously. The power output value is changeable from 1/1 full power to Min. power in 0.3 stop increments, until one of the group's setting turns to the maximum (1/1) or the minimum (Min.). If the current group is in the TTL mode, all the other groups which are in the M mode will change their FEC amount simultaneously. The FEC amount is changeable from -3 to 3 in 0.3 stop increments, until one of the group's setting turns to the maximum (3) or the minimum (-3). If the current group is in the -- mode (flash off), the amounts will not change.
- Short press the <GR> Button again to confirm the setting.
- Test Flash:
- Press the <TEST> Trigger Button to see whether flash will fire normally or not.
- Fully press the <TEST> Trigger Button, and the Status Indicator Lamp turns red and the flash can be triggered.
- The settings on the transmitter end will synchronize to the receiver end at the same time.
- Modeling Lamp Control: Double-click the <CH/OK> Button to power ON/OFF the modeling lamp.
- Automatically Enter Power Saving Mode:
- The flash trigger will go into standby mode after the transmitter enters sleep mode, and the displays on the LCD panel will disappear.
- Press any of the button (<TEST> fully pressed/<CH/OK>/<GR>/<MODE>) can wake up the flash trigger. If the transmitter is attached to the camera, half press the shutter can also wake up the system.
- If the transmitter is set to single contact mode (icon displayed), the system will not enter power saving mode.
- C.Fn: Setting Custom Functions: The following table lists the available and unavailable custom functions of this flash. Note: Some icons will be displayed when setting the relevant custom functions to make users have a good understanding.
Custom Functions No. Functions Setting Signs Settings and Description C.Fn-00 Synchronization delay setting 00
1~100OFF
Master flash synchronization delay N*100 us (synchronization delay icon is displayed.)C.Fn-01 Single contact mode on ON (The single contact mode set icon is displayed.) It is advisable to set the transmitter to single contact mode when using it to trigger the flash by PC cord or through camera's single contact. C.Fn-02 Zoom setting 16,18,23,33,46,53,69 Zoom is off
Zoom value in 135 system (24/28/35/50/70/80/105 mm)C.Fn-03 PC sync socket connects with camera in
ouPC sync socket connects with camera/camera flash
PC sync socket connects with flashC.Fn-04 Multi Flash ON/OFF on Multi flash OFF
Multi flash ONC.Fn-05 Minimum power output in M/Multi mode 1/128
1/256The minimum power output in M/Multi mode is 1/128
The minimum power output in M/Multi mode is 1/256C.Fn-06 AF assist ON
on
OFFON
on
OFFC.Fn-07 Number of groups 03
05A/B/C
A/B/C/D/EC.Fn-08 Beep ON
on
OFFON
on
OFFC.Fn-09 Send setting values forcibly Only send after the setting values have been changed.
Forcibly send the setting values before firing even though the values has not been changed.C.Fn-10 APP mode on The transmitter is in the master mode, which can set the receiver's mode and output on the transmitter end.
Open the APP mode and the transmitter can only trigger flashes. Only channel and custom settings can be adjusted and the LCD panel will display APP.C.Fn-11 Setting the specific cameras and flashes 00
01
02The general Canon cameras
The cameras that use between-the-lens-shutters e.g. X100F, X100T, etc. Choose this option and set all groups to M mode can reach high-speed sync within 1/1250s.
Choose this option and set all groups to M mode can solve the problem that the TT600 and V850II cannot achieve high-speed sync flash when triggered by X1T-F.
Setting the Camera
To trigger X1T-C, please set camera's flash mode to TTL flash.

Canon Camera side flash mode setting:
- Flash control mode: The flash control mode selected with the flash unit. This can in some cases be adjusted from the camera; the options available vary with the flash.
- TTL: TTL mode. Adjust flash compensation.
- MULTI: Repeating flash. Compatible shoe-mounted flash units will fire multiple times with each shot.
- OFF: The flash does not fire. Some flash units can be turned off from the camera.
- Flash compensation/output: The options available vary with flash control mode.
- TTL: Adjust flash compensation (the full value may not be applied if the limits of the flash control system are exceeded). In the cases of the EF-X20, EF-20, and EF-42, the selected value is added to the value selected with the flash unit.
- MULTI: Adjust flash output (compatible units only).
- Flash mode (TTL): Choose a flash mode for TTL flash control. The options available vary with the shooting mode (P, S, A, or M) selected.
- FLASH AUTO: The flash fires only as required; flash level is adjusted according to subject brightness. A icon displayed when the shutter button is pressed halfway indicates that the flash will fire when the photo is taken.
- TTL (STANDARD): The flash fires with every shot if possible; flash level is adjusted according to subject brightness. The flash will not fire if not fully charged when the shutter is released.
- SLOW SYNC.: Combine the flash with slow shutter speeds when photographing portrait subjects against a backdrop of night scenery. The flash will not fire if not fully charged when the shutter is released.
- Sync: Control flash timing.
- FRONT (1ST CURTAIN): The flash fires immediately after the shutter opens (generally the best choice).
- REAR (2ND CURTAIN): The flash fires immediately before the shutter closes.
- AUTO FP (HSS): High-speed sync (compatible units only). The camera automatically engages front-curtain high-speed sync at shutter speeds faster than the flash sync speed. Equivalent to 1ST CURTAIN when MULTI is selected for flash control mode.
- Zoom: The angle of illumination (flash coverage) for units that support flash zoom. Some units allow the adjustment to be made from the camera. If AUTO is selected, zoom will automatically be adjusted to match coverage to lens focal length.
- Lighting: If the unit supports this feature, choose from the options below.
- FLASH POWER PRIORITY: Gain range by slightly reducing coverage.
- STANDARD: Match coverage to picture angle.
- EVEN COVERAGE PRIORITY: Slightly increase coverage for more even lighting.
- LED light: Choose how the built-in LED light functions during still photography (compatible units only). It can function as a catchlight, as an AF-assist illuminator, or as both a catchlight and an AF-ASSIST illuminator. Choose OFF to disable the LED during photography.
- Number of flashes: Choose the number of times the flash fires each time the shutter is released in MULTI mode.
- Frequency: Choose the frequency at which the flash fires in MULTI mode. *Full value may not be applied if limits of flash control system are exceeded.
Maintenance
- Avoid sudden drops: The device may fail to work after strong shocks, impacts, or excess stress.
- Keep dry: The product isn't waterproof. Malfunction, rust, and corrosion may occur and go beyond repair if soaked in water or exposed to high humidity.
- Avoid sudden temperature changes: Condensation happens if sudden temperature changes such as the circumstance when taking the transceiver out of a building with higher temperature to outside in winter. Please put the transceiver in a handbag or plastic bag beforehand.
- Keep away from strong magnetic field: The strong static or magnetic field produced by devices such as radio transmitters leads to malfunction.
Troubleshooting
- Unable to trigger flash or camera shutter: Make sure batteries are installed correctly and Power Switch is turned on. Check if the transmitter and the receiver are set to the same channel, if the hotshoe mount or connection cable is well connected, or if the flash triggers are set to the correct mode.
- Camera shoots but does not focus: Check if the focus mode of the camera or lens is set to MF. If so, set it to AF.
- Signal disturbance or shooting interference: Change a different channel on the device.
- Operating distance limited or flash missing: Check if batteries are exhausted. If so, change them.
Specifications
| Feature | Specification |
|---|---|
| Model | X1T-C |
| Compatible Cameras | Canon EOS cameras (E-TTL II autoflash); Support all cameras that have PC sync socket |
| Built-in Remote System | 2.4G Wireless Transmission |
| Modulation Method | MSK |
| Power Supply | 2*AA batteries |
| Manual Flash | Support |
| TTL Auto Flash | E-TTL II |
| High Speed Sync (HSS) | Support |
| Flash Exposure Compensation (FEC) | Support, ±3 stops in 1/3 stop increments |
| Flash Exposure Lock (FEL) | Support |
| Focus Assist | Manual open |
| Rear Curtain Sync | No |
| Modeling Flash | Support, fired with cameras depth of field preview button |
| Wireless Function | In TTL mode, Ratio off; in M mode, Flash Ratio(A B C); Support GR (grouping flash) |
| Controlled Slave Groups | In GR grouping mode, 5 (A/B/C/D/E); in Ratio grouping mode, 3(A/B/C) |
| Transmitter Distance | >100 meters |
| Channel | 32 channels |
| Synchronization Delay Set | Support (0-10ms, set in unit of 100us) |
| Wireless Shutter Release | Receiver can control cameras shooting through 2.5mm shutter release interface |
| Zoom Setting | The focal length can be adjusted through the transmitter |
| Display Panel | Wide LCD panel, backlight on/off |
| Output Interface | Transmitter: use a PC port to input and output; Receiver: use a 2.5mm sync cable to output |
| Firmware Upgrade | Use the Micro USB port to upgrade |
| Memory Function | Settings will be stored 2 seconds after last operation and recover after a restart |
| Transmitter Size/Weight | 72x75x52(mm)/100g |
Compatible Camera Models
The Godox X1T-C is compatible with Canon EOS cameras (E-TTL II autoflash) and supports all cameras that have a PC sync socket.
Note: This table is based on the X1T-F (Fujifilm) manual. While general compatibility with Canon EOS cameras is stated, specific model support may vary. Always test with your specific camera model.

User Tips
- Ensure fresh batteries are used for optimal performance, especially when experiencing range issues.
- If experiencing interference, try changing the channel on both the transmitter and receiver.
- For precise control, familiarize yourself with the custom functions (C.Fn) to tailor the transmitter to your specific shooting needs.