DEKO MMA-200A-D

Contents

DEKO MMA Series ARC Welder Instruction Manual

Model: MMA-200A-D (Applicable to MMA-160, DKA-200Y, DKA-250Y, AE-200 series)

Brand: DEKO

1. Important Safety Cautions & Symbols

WARNING: Welding equipment can be dangerous to both the operator and people in or near the surrounding working area if the equipment is not correctly operated. Equipment must only be used under the strict and comprehensive observance of all relevant safety regulations. Read and understand this instruction manual carefully before the installation and operation of this equipment.

1.1. Electric Shock

Touching live electrical parts can cause fatal shocks or severe burns. The electrode and work circuit are electrically live whenever the output is on. The input power circuit and machine internal circuits are also live when power is on.

  • Do not touch live electrical parts.
  • Insulate yourself from work and ground using dry insulating mats or covers big enough to prevent any physical contact with the work or ground.
  • Do not remove any machine covers while the machine is powered.

1.2. Welding Workplace

Be mindful of working in cramped positions, scaffolds, or any location where you can fall and become injured.

  • Wear a safety harness if working above floor level.
  • Do not work in wet areas, or while wearing wet clothing.

1.3. Welded Parts

Immediately after welding, all-welded parts will be at a very high temperature which will cause burns to any exposed skin that makes contact.

  • Do not touch parts after welding. Allow for a cooling period before picking up.
  • To handle hot parts, use proper tools and/or wear heavy, insulated welding gloves and clothing to prevent burns.

1.4. Welding Fumes

Welding produces fumes and gases. Breathing these fumes and gases can be hazardous to your health.

  • Keep your head out of the fumes stream while welding. Do not breathe the fumes.
  • If inside, ventilate the area and/or use local forced ventilation at the welding point to remove welding fumes and gases.
  • If ventilation is poor, wear an approved air-supplied respirator.
  • Work in a confined space only if it is well ventilated, or while wearing an air-supplied respirator. Welding fumes and gases can displace air and lower the oxygen level causing injury or death. Always have a trained watch person nearby.
  • Do not weld on coated metals, such as galvanized, lead, or cadmium plated steel, unless the coating is removed from the weld area, the area is well ventilated, and while wearing an air-supplied respirator. The coatings and any metals containing these elements can give off toxic fumes if welded.

1.5. Welding Rays

Rays from the welding process produce intense visible and invisible (ultraviolet and infrared) rays that can burn eyes and skin.

  • Wear an approved welding helmet fitted with a proper shade of filter lenses to protect your face and eyes from welding rays.
  • Use protective screens or barriers to protect others from flash, glare, and sparks; warn others not to watch the arc.
  • Wear protective clothing made from durable, flame-resistant material (leather, heavy cotton, or wool) and cover any exposed skin, arms, neck area.

1.6. Welding Fires

Welding produces heat and can lead to fires, as well certain welding forms create sparks which could also ignite surrounding items and create a fire. The flying sparks, hot workpiece, and hot equipment can cause fires and burns.

  • Remove all flammables within 35 ft. (10.7m) of the welding arc. If this is not possible, cover them with approved covers.
  • Be alert that welding sparks and hot materials from welding can easily go through small cracks and openings to adjacent areas. Be aware that welding on a ceiling, floor, bulkhead, or partition can cause fire on the hidden side.
  • Watch for fire, and keep a fire extinguisher nearby.

1.7. EMF-Electric Magnetic Fields

During welding, electric magnetic fields are created and can produce malfunctions in electrical components within the area.

  • EMF created by welders may affect wearers of pacemakers and other implanted devices should keep away.
  • Implanted Medical Device wearers should consult their doctor and the device manufacturer before going near arc welding, spot welding, gouging, plasma arc cutting, or induction heating operations.

1.8. Excessive Noise

Be mindful if your working area creates excessive noise.

  • Wear approved ear protection if the noise level is high.
  • Any workers close by the area will also be affected by the noise and may also require hearing protection.

1.9. Moving Parts

Several moving parts may be in typical welding machines such as rollers and fans.

  • Keep hands away from moving parts such as fans.
  • Keep all doors, panels, covers, and guards closed and securely in place.
  • Keep away from moving parts.
  • Keep away from pinch points such as drive rolls.
  • Secure any loose clothing and hair and keep away from moving parts.

1.10. Additional Safety Instructions

1.10.1. The Environment for Using

  • The welding operation shall be carried out in a relatively dry environment, air humidity generally should not exceed 90%.
  • Temperature should be around minus 10 degrees to 40 degrees Celsius.
  • Avoid welding in the sun or rain, don't let the water or rain infiltrate into the welding machine.
  • Avoid welding under the environment of dust area or containing corrosive gas.
  • Avoid working in the environment of the strong airflow for gas shielded welding operation.
  • Welding machine should be placed in a horizontal position, and the gradient must not exceed 15 degrees.

1.10.2. Safety Point

The welding machine has been installed in an over-voltage, and over-current and overheating protection circuit. The welding machine will automatically stop working when the grid voltage, output current, and internal temperature are higher than the set standard. But the excessive use (high voltage) still can lead to the welding machine breakdown, so you need to pay attention to the following items:

  • Ensure good ventilation: It is an industrial welding machine. In operation, natural ventilation cannot meet the requirement to cool the welding machine as the high working current through the welding machine, so we built-in two fans to effectively cool the welding machine to make it work smoothly. Users shall confirm the ventilated place has not been covered or blocked. The welding machine and the surrounding distance of the object should not be less than 0.3 meters. Users should always pay attention to maintaining good ventilation, which is very important for the welder better job and ensure longer service life.
  • No overloading working: Users must use a welding machine by the duty cycle rate, and the welding current shall not exceed the maximum load current, which can significantly shorten the service life and may even burn the welder.
  • No over-voltage working: Users can check the power voltage range of the machine in the main parameter table, the inner voltage will auto complement within the range, and guarantee the welding current will not surpass the allowed value. Please be more careful or the parts will be damaged because of the over-voltage.
  • Grounding: Each machine has a screw for the earth connecting to block the earth signal, please choose a 2.5mm cable to connect the case from the machine to ear, to avoid breakdown caused by static electricity or electricity-leaking.
  • Overheating Protection: If the welding work is more than the duty cycle, the machine will be excessive heat and trigger the temperature control switch, the welding machine will enter into the state of protection and suspend the work.
  • Protection Light: There is a protection light design, when the light is on, the cooling fan can continue to work even users don't unplug the power; when the light is off, the temperature of the machine drops to the standard range, then users can start welding.

2. Product Overview

The DEKO MMA Series ARC Welder is a versatile 2-in-1 multi-process welding machine designed for both MMA (Stick) and Lift TIG welding. Featuring advanced IGBT inverter technology, it provides stable arc, high efficiency, and is suitable for a wide range of metals including mild steel, carbon steel, stainless steel, and cast iron. Its compact and portable design makes it ideal for various applications from home DIY projects to professional use.

DEKO MMA Series ARC Welder with accessories

Figure 2.1: DEKO MMA Series ARC Welder with included accessories.

Video 2.1: Product demonstration of the DEKO MMA Series ARC Welder.

2.1. Key Features

  • Advanced IGBT Inverter Technology: Ensures stable arc, high efficiency, and energy conservation.
  • 2-in-1 Multi-Process Welder: Supports MMA (Stick) and Lift TIG welding modes.
  • Digital Display: Accurately shows current data for precise operation.
  • Security Protection: Includes overheat, overcurrent, and overload protection with automatic shutdown.
  • Hot Start, Anti-Sticking, Arc Force: Features for smoother welding, easy arc starting, and preventing electrode sticking.
  • Wide Application: Suitable for welding cast iron, mild steel, sheet metal, stainless steel, square pipe, and metal cages.
  • Compact & Portable: Lightweight design with a handle and adjustable shoulder strap for easy transport.
Superior Performance MMA Welding Machine features

Figure 2.2: Superior performance features including sturdy design, high efficiency fan, stable current, and IGBT technology.

2 IN 1 Multi-Process Welder showing Stick and Lift TIG

Figure 2.3: The welder supports both Stick and Lift TIG welding processes.

Security Protection features: Digital Display, Overheating, Overload

Figure 2.4: Built-in security protections for safe operation.

Wide Range of Metals for welding: Cast Iron, Mild Steel, Sheet Metal, Stainless Steel, Square Pipe, Metal Cage

Figure 2.5: Examples of metals that can be welded with this machine.

Portable & Powerful: Size 32x22x13cm, Weight 3.20 kg

Figure 2.6: Dimensions and weight highlighting portability.

3. Specifications

3.1. Technical Data

AttributeValue
Model No.MMA-200A-D
Input Voltage (V)AC 1~110V / AC 1~220V
Input Power (KW)8.8
Efficiency (%)85%
Power Factor0.93
No-Load Voltage (V)60V
Current Range (A)220V: 10-190A / 110V: 10-160A
Duty Cycle (%)60%
Electrode DiameterΦ1.6-5.0mm
Insulation DegreeF
Protection DegreeIP21S
Dimensions32*22*13cm
Net Weight (N.W.)3.2kg

3.2. Product Description (Front & Back Panels)

Front panel of DEKO MMA Welder with labels for controls and indicators

Figure 3.1: Front Panel Layout

  • 1. Welding current adjustment knob: Adjust the input current.
  • 2. Overheat indicator light: When lit, indicates the internal temperature is too high (thermal protection).
  • 3. Power indicator light: When lit, indicates the machine power switch is on.
  • 4. Negative output terminal: Connect the earth clamp.
  • 5. Positive output terminal: Connect the electrode holder.
  • 6. Power control switch: Turns the machine on/off.
  • 7. Current meter: Displays the welding current.

NOTE: The accessories are subject to change without notice.

3.3. Electrical Principle Diagram

Electrical principle diagram of the inverter welding machine

Figure 3.2: Electrical Principle Diagram

4. Setup

WARNING: Please install and debug the welder as per the following steps. Electrical connection should be operated after the distribution box shuts down. The protection class is IP21S, and it is not allowed to use in rain.

  1. Each machine is equipped with a cable; please connect the cable with relevant voltage grade according to the welding machine's input voltage.

    NOTE: Don't mistake the voltage grade.

  2. The connection between the primary power supply and power terminal/sockets should be great to prevent oxidation.
  3. Check whether the Single-phase input voltage value is within the wave range with a multimeter.
  4. Connect the cable with the welding holder into the front panel's positive socket and tighten clockwise.
  5. Connect the cable with clamp into the front panel's negative socket and tighten clockwise.

    NOTE: The connection as mentioned above (steps 4 and 5) is the DCEP connection. The operator can choose a DCEN connection according to workpiece and electrode application requirements. Generally, a DCEP connection is recommended for basic electrodes, while there is no special requirement for the acid electrode.

  6. Please grounding the marked screw of the back panel and ensure a good connection.

    NOTE: It is a dual voltage MMA welder.

Welder connection diagram showing power supply, adapter cable, positive and negative outputs, and base metal

Figure 4.1: Connection Diagram for Welding Machine

5. Operation

  1. Turn on the switch, the power indicator light lits, the fan works normally, and the welding machine starts working.
  2. Pay attention to the cable connection polarity, generally, there are two modes: DCEN and DCEP.
    • DCEN: welding holder connect negative, workpiece connect positive;
    • DCEP: workpiece connect negative, welding holder connects positive.
    If the connection between cables is wrong, an unstable arc, big splash, and electrode stick will happen.
  3. To reduce the decline of cable voltage, please choose the cable with a bigger sectional area if there is a great distance between the workpiece, the welding machine, and two cables (welding cable and earthing cable).
  4. Adjust the welding current according to the electrode's specification, clip the electrode, make use of a short circuit arc, then it can welding. Users can take the sheet as a reference for welding parameters.

5.1. Welding Process Parameters (Reference Only)

Electrode Diameter (mm)Recommended Current (A)Recommended Welding Voltage (V)
1.020~5020.8~22
1.630~6021.2~22.4
2.050~9022~23.6
2.570~12021.8~24.8
3.290~14023.6~25.6
4.0130~20025.2~28

The data in this table is suitable for welding low carbon steel; other materials you can refer to the material and process manual.

Welder in use, showing Stick and Lift TIG welding

Figure 5.1: The welder supports both Stick and Lift TIG welding processes.

6. Maintenance

WARNING: Before performing any work on the equipment, pull the power plug.

  1. Regularly check the circuit connection of the welding machine to confirm whether the wiring is correct, firmly connect the head (especially the insert joint or components). If there is rust or the connection is loose, please remove the rust or oxide film, then reconnect, and tighten.
  2. When power is on, do not let hand, the hair close to electrification device in the machine, such as fan, avoid injury or machine damage.
  3. Regularly use a dry air compressor to blow off the dust; if the welder is used in a smoke and air pollution environment, then it should be dusted every day.
  4. Avoid water or water vapor in the internal welding machine. If it happens, dry interior welding machine, then measure the insulation situation of welding machine by the tramegger (including between connection point and between connections and the case).
  5. Regularly check whether the insulation skin of all welding machine cables is damaged, then bind up or replace the cable.
  6. If don't use the welding machine for a long time, the machine should be stored the original packaging in a dry environment.

7. Troubleshooting

ProblemCausesRemedy
The power light doesn't lit, the fan doesn't work and the machine doesn't work.
  1. The power is switched off.
  2. Poor power connection.
  1. Check whether the power switch is on.
  2. Check the power connection.
The welding current is unstable.
  1. The pressure arm on the wire feeder is not properly adjusted.
  2. The drive roll doesn't match the wire size being used.
  3. The contact tip of the welding torch is badly worn.
  4. The wire-feeding tube of the welding torch is badly worn.
  5. The electrode is of poor quality.
  1. Adjust to get the proper pressure setting.
  2. Make sure the wire and roll size is a match.
  3. Replace it.
  4. Replace it.
  5. Change electrode supply.
Poor welding result.
  1. Poor connection of earth clamp.
  2. The voltage is irregular/ too low/ too high.
  1. Check that the earth clamp is firmly attached, the point of attachment is clean and that the cable and its connectors are intact.
  2. Check that the electric voltage is not irregular or too low/ high.
The electrode holder becomes very hot during welding.The rated current of the electrode holder is smaller than its actual working current.Replace the electrode holder with a higher-rated one.
There is a big splash during welding.The connection of output polarity is wrong.Replace the output line.
The overheating LED is on.The overheating protection circuit has reached its limit and shut down the machine.
  1. Ensure the welding machine is in an open area able to receive sufficient air flow.
  2. Ensure the fan is functioning.
  3. Disconnect power source and inspect if the inside of the machine is filled with dust-clean/ blow out machine as necessary.

8. User Tips

  • For general home use and DIY projects, the 200A model is often recommended for its versatility and ability to handle electrodes up to 4mm.
  • If you experience unstable power supply, consider connecting the welder through a voltage stabilizer or a portable generator with sufficient power reserve to ensure consistent performance.
  • The included cables might be shorter for some applications; consider purchasing longer, higher-gauge cables if your work requires more reach.
  • Utilize the Hot Start, Anti-Sticking, and Arc Force features to achieve smoother welds and prevent electrodes from sticking, especially for beginners.
  • When welding stainless steel (inox), ensure the earth clamp is connected to the negative terminal for optimal polarity.
  • This welder is well-suited for small to medium-sized jobs around the house or farm.

9. Warranty & Support

This tool is warranted to the original purchaser to be free from defect in materials and workmanship for a period of 2 years from the original purchase date.

If the tool should fail some day in spite of our quality controls and materials, only have it repaired by an authorized electrician or contact your local distributor or service agent.

Or you can contact us by emails: services@dekotools.com, support@dekotools.com

9.1. Warranty Exclusions

The warranty will not apply to the following cases:

  • where this product has been subjected to misuse, abuse, accident or want of care;
  • where this product has been used for a purpose for which it was not designed or is not suited;
  • where the service of this product has been undertaken by a non-authorized person or company or if non-approved parts have been used.
  • components that are subject to natural wear and tear caused by use in accordance with operating instructions.

10. Disposal

The machine and packaging should be sorted for environmental-friendly recycling. Do not dispose of power tools into household waste! Please recycle them at collection points provided for the purpose. Ask your local authority for information about recycle.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.