1. Product Overview
The LMODRI Universal Motorcycle Back Side Mirrors are designed to provide enhanced rear visibility for a wide range of motorcycles, electrombiles, electric bicycles, mopeds, and scooters. These mirrors feature a durable construction and offer adjustable viewing angles for optimal safety.
2. Safety Warnings
- Before Installation: Park the motorcycle on flat ground, support it with the main stand, and turn off the power to prevent the vehicle from tipping over and causing injury.
- Auxiliary Tool: This rear view mirror is only an auxiliary tool for observing road conditions behind. Always turn your head to check directly before turning or changing lanes; do not rely entirely on the mirror.
- Mirror Damage: The mirror surface is made of glass. Stop using it immediately if cracks or damage occur to avoid injury from flying fragments.
- Secure Fastening: After installation, make sure the bracket is securely fastened. Looseness or shaking during riding will affect vision judgment and cause danger.
3. Installation Steps
3.1 Tools Preparation
- Phillips screwdriver
- Wrench (selected according to screw specifications)
3.2 Installation Procedure
- Remove Original Mirror: Use a wrench to unscrew the original rear view mirror on the handlebar. Clean any dust and oil from the mounting hole.
- Confirm Interface Specification: Check whether the handlebar thread is 8mm or 10mm, and select the corresponding mirror interface.
- Preliminary Fixation: Align the mirror bracket with the handlebar interface and screw in the bolt by hand until preliminarily fixed. Do not use excessive force to avoid thread slipping.
- Pre-adjust Angle: Sit in the standard riding position, rotate the mirror and bracket to roughly adjust the angle for a clear rear view.
- Final Tightening: Use a wrench to tighten the bolt. The recommended torque is 15-20 N·m to ensure no looseness or shaking during riding.
- Installation Check: Gently shake the mirror by hand to confirm it is firm and the angle is correct. Installation is complete.
4. Mirror Adjustment Method
- Maintain a normal riding posture, hold the handlebars with both hands, and look straight ahead.
- Left Mirror: Rotate the mirror so the horizon is at the upper 1/3 of the mirror, clearly covering the left rear lane and roadside.
- Right Mirror: Rotate the mirror so the horizon is at the center, clearly covering the right rear and adjacent lanes.
- After adjustment, recheck the bracket to ensure the angle will not shift due to vibration while riding.
5. Maintenance & Care
- Daily Cleaning: Wipe the mirror with a soft cloth (such as eyeglass cloth) dampened with clean water or neutral detergent. Do not use rough cloths, steel wool, or alcohol to avoid scratching the coating.
- Regular Inspection: Every 500 km or monthly, check whether bracket screws are loose and whether the mirror has cracks or scratches. Tighten or replace parts promptly if problems are found.
- Storage Protection: When the motorcycle is not in use for a long time, cover the mirrors with a dust-proof cloth to prevent aging of the housing and fading of the mirror due to direct sunlight.
- Environmental Protection: Dry water stains on the mirror and bracket after riding in rain to prevent rust. In low-temperature environments, avoid flushing the mirror with hot water to prevent glass breakage from extreme temperature differences.
6. Troubleshooting
- Mirror is loose or shaking after installation: Re-check and tighten all mounting bolts to the recommended torque (15-20 N·m). Ensure the bracket is securely fastened.
- Poor rear visibility: Adjust the mirror angle according to the "Mirror Adjustment Method" section. Ensure the horizon is correctly positioned in both left and right mirrors.
- Mirror surface is cracked or damaged: Immediately stop using the mirror and replace it to prevent injury from flying fragments.
- Mirror housing or glass appears aged/faded: Ensure mirrors are covered with a dust-proof cloth when the motorcycle is stored for extended periods, especially from direct sunlight.
- Rust on mirror or bracket: Dry water stains after riding in rain.
7. Specifications
| Attribute | Detail |
|---|---|
| Brand | LMoDri |
| Model Name | F2181-2nd |
| Item Type | Side Mirrors & Accessories |
| Material | Plastic Mirror Case + Iron Mirror Stem |
| Mirror Diameter | Approx. 11 cm |
| Stem Length | Approx. 20 cm |
| Item Width | 11 cm |
| Item Length | 29 cm |
| Item Weight | 480g |
| Thread Interface | 8mm Clockwise OR 10mm Clockwise |
| Glass Type | White and Convex Glass |
| Origin | Mainland China |
| Package Contents | 1 Pair (1 Pc Left + 1 Pc Right) Motorcycle Mirror |
| Package Dimensions | 22cm (Length) x 22cm (Width) x 6cm (Height) |
| Package Weight | 0.55 kg |
8. User Tips
- Always verify your motorcycle's existing mirror thread size (8mm or 10mm) before installation to ensure compatibility.
- When installing, screw in bolts by hand first to avoid cross-threading or stripping, then use a wrench for final tightening.
- Regularly check mirror screws for tightness and inspect the mirror surface for cracks or damage to ensure safe riding.
9. Frequently Asked Questions (FAQ)
- Q: What thread sizes are these mirrors compatible with?
- A: These mirrors are compatible with motorcycles and scooters that have an 8mm clockwise or 10mm clockwise thread interface. Please verify your vehicle's thread size before purchase.
- Q: What is the thread pitch for the 10mm mirrors?
- A: While some users report M10 x 1.5, and others M10 x 1.25, the product is generally compatible with standard 10mm clockwise threads. It is recommended to check the specific product received or your motorcycle's requirements.
- Q: Can these mirrors be rotated?
- A: Yes, the mirrors feature 360-degree rotation for optimal angle adjustment.
10. Warranty and Support
For detailed warranty information and customer support, please refer to the seller's policies on the product page. A comprehensive user manual in PDF format may also be available for download: