eletechsup DD0603SA_3V3

Contents

DD0603SA_3V3 Auto Buck-Boost DC-DC Converter Board User Manual

1. Product Overview

The DD0603SA_3V3 is a compact auto buck-boost DC-DC converter module designed to provide a stable 3.3V output from a wide input voltage range of 0.9V to 6V. This module automatically switches between step-up (boost) and step-down (buck) modes to maintain the desired output voltage, making it suitable for various battery-powered applications and development boards.

Front view of the DD0603SA_3V3 converter board with '3V3' text

Figure 1: DD0603SA_3V3 Converter Board (Front View)

Front and back view of the DD0603SA_3V3 converter board

Figure 2: DD0603SA_3V3 Converter Board (Front and Back View)

Video 1: Product demonstration and overview of the DD0603SA_3V3 converter board.

2. Setup and Connections

2.1 Pinout Description

  • Vi: Voltage Input (0.9V - 6V DC)
  • GND: Ground (Common for input and output)
  • Vo: Voltage Output (3.3V DC)

2.2 Wiring Diagram

Connect your power source to the 'Vi' and 'GND' input pins, and your load to the 'Vo' and 'GND' output pins as shown in the diagram below. Ensure correct polarity to prevent damage to the module and connected devices.

Wiring diagram for DD0603SA_3V3 showing input and output connections

Figure 3: Wiring Diagram

2.3 Important Setup Notes

  • The input voltage must not exceed 6.5V. Exceeding this voltage may permanently damage the module.
  • Ensure that the output power required by your load does not exceed the module's maximum continuous load capacity for extended periods.
  • The input power supplied to the module must always be greater than the output power delivered to the load, accounting for the module's own power consumption (efficiency is 61%-85%).
  • The module features a 2.54mm pin pitch, making it compatible with standard breadboards and MCU development boards.

3. Operating Instructions

Once correctly wired, apply power within the specified input voltage range (0.9V to 6V). The module will automatically regulate the output to 3.3V. It is designed for continuous operation within its specified temperature and current limits.

3.1 Typical Applications

  • Battery-powered equipment (e.g., 1xAA, 2xAA, 3xAA, 18650 cells)
  • Breadboard power supply for prototyping
  • Powering ARM, FPGA, CPLD, MCU development boards
  • Small power motors and electrical tools
  • Cameras, video cameras, and toy cars
  • LED lighting and wireless communication equipment
  • Audio equipment requiring 3.3V

4. Maintenance

The DD0603SA_3V3 converter board is a solid-state electronic component and requires minimal maintenance. To ensure longevity and reliable operation:

  • Keep the module dry and free from dust and corrosive substances.
  • Avoid exposing the module to extreme temperatures outside its operating range (-25°C to +85°C).
  • Ensure adequate ventilation if the module is enclosed, especially when operating at higher loads, to prevent overheating.
  • Do not apply mechanical stress or excessive force to the pins or components.

5. Troubleshooting

5.1 Common Issues and Solutions

  • Issue: Output voltage is lower than 3.3V.
    Solution: This often indicates that the input power supply is insufficient. Use a multimeter to check the input voltage directly at the module's input pins. If the input voltage drops significantly under load, provide a more robust power source.
  • Issue: Unstable or poor output voltage regulation.
    Solution: This can occur if the output current exceeds approximately 300mA, or if the input voltage is too low (e.g., below 1.2V under load). Ensure your load current is within the specified limits and that the input voltage is stable and sufficient.
  • Issue: Module not functioning.
    Solution: Verify all connections for correct polarity and secure contact. Check if the input voltage is within the 0.9V-6V range and does not exceed 6.5V. Inspect for any visible damage to the module.

6. Specifications

Image showing dimensions and weight of the converter board

Figure 4: Dimensions and Weight

ParameterValue
Model NumberDD0603SA_3V3
Input Voltage (Vi)DC 0.9V - 6V
Maximum Input Voltage6.5V
Output Voltage (Vo)DC 3.3V (±5%)
Output Current (Max)<0.8A
Working Frequency1MHz
Efficiency61% - 85%
Operating Temperature-25°C to +85°C
Storage Temperature-45°C to +125°C
Dimensions (L x W x H)22mm x 15mm x 5.7mm
Weight2.6g
Pin Pitch2.54mm
CertificationNONE

6.1 Measurement Results (Reference Only)

The following table provides typical measurement results under various input conditions. These values are for reference and may vary slightly based on specific operating conditions and load characteristics.

Table of measurement results for input voltage, input current, output voltage, and output current

Figure 5: Measurement Results Table

Input VoltageInput CurrentOutput VoltageOutput Current
1.2V0.55A3.3V0.13A
1.5V1A3.3V0.3A
1.8V1.34A3.3V0.51A
2.5V1.38A3.29V0.8A
3V1A3.28V0.8A
3.3V0.97A3.28V0.8A
3.7V0.9A3.27V0.85A
4.2V0.78A3.27V0.85A
4.5V0.72A3.27V0.85A
5V0.64A3.27V0.85A
6V0.53A3.27V0.85A

7. User Tips

  • For optimal output voltage regulation, especially when driving loads, try to keep the output current below 300mA.
  • When operating with a load, ensure your input voltage is at least 1.2V for more stable performance.
  • If you experience lower than expected output voltage, always verify the input power source's capacity and stability with a multimeter.
  • Consider adding small input/output capacitors (e.g., 10uF) if your application is sensitive to voltage ripple, although the module is designed for stable operation.

8. Warranty and Support

This product does not come with an explicit manufacturer's warranty statement in the provided documentation. For any technical support, troubleshooting assistance, or warranty inquiries, please contact your original seller or the manufacturer directly.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.