ALCTRON DI120

Contents

Alctron DI120 Dual Channel Passive Direct Box User Manual

Model: DI120 | Brand: ALCTRON

1. Introduction

Alctron DI120 Dual Channel Passive Direct Box, front view in blue.

Figure 1: Alctron DI120 Dual Channel Passive Direct Box (Blue model shown)

The Alctron DI120 is a robust dual-channel passive direct box designed to convert high-impedance, unbalanced instrument signals into low-impedance, balanced signals suitable for direct connection to mixing consoles or PA systems. It is ideal for use with guitars, basses, keyboards, and other audio equipment, ensuring clean signal transfer and minimizing noise over long cable runs. Being a passive unit, it does not require external power, making it a reliable and convenient tool for live performances and studio recordings.

2. Key Features

  • Dual Channel Design: Allows connection of two independent instruments simultaneously.
  • Passive Operation: No external power (battery or phantom power) required for operation.
  • High-Quality Signal Conversion: Converts Hi-Z instrument signals to Lo-Z XLR outputs.
  • Attenuation Switches: Provides 0dB, -20dB, and -40dB attenuation options to handle various input levels.
  • Ground Lift Switch: Helps eliminate hum and buzz caused by ground loops.
  • Parallel Output (Para Out): Allows the original instrument signal to be sent to an amplifier or monitor while simultaneously feeding the DI box.
  • Durable Construction: Heavy-duty metal casing with rubber feet for protection and stability.

3. Package Contents

Please check that all items are present in the package:

  • 1 x Alctron DI120 Dual Channel Passive Direct Box
  • 1 x User Manual
  • 1 x Warranty Card

4. Setup and Connections

The Alctron DI120 features two independent channels for connecting instruments. Each channel includes a 1/4" TS input, a 1/4" TS parallel output (Para Out), an attenuation switch, an XLR balanced output, and a ground lift switch.

4.1 Front Panel Connections

Front view of Alctron DI120 showing 1/4 inch input and para out jacks, and attenuation switches.

Figure 2: Front Panel of the DI120 (Silver model shown)

  • INPUT 50K (1/4" TS Jack): Connect your instrument (e.g., guitar, bass, keyboard) here.
  • PARA OUT 50K (1/4" TS Jack): This is a parallel output that sends the original, unprocessed signal to an instrument amplifier or monitor.
  • Attenuation Switches (0dB, -20dB, -40dB): These switches reduce the input signal level. Use 0dB for standard signals, -20dB for hotter signals, and -40dB for very hot signals (e.g., speaker outputs) to prevent clipping.

4.2 Rear Panel Connections

Rear view of Alctron DI120 showing balanced XLR outputs and ground lift switches.

Figure 3: Rear Panel of the DI120 (Silver model shown)

  • BALANCED IN/OUT 600Ω (XLR Output): Connect these balanced XLR outputs to the microphone inputs of your mixing console or PA system.
  • GROUND Switch (ON/OFF): This switch disconnects the ground connection between the input and output. Use it to eliminate hum or buzz caused by ground loops. The "Lift" position (OFF) is generally recommended unless noise is present.

4.3 Connection Examples

The DI120 can be used in various configurations:

Diagram showing a guitar connected to the DI box input, with the parallel output going to a guitar speaker and the XLR output going to a console.
Figure 4: Example Connection for Guitar (DI Box front panel shown)
Diagram showing a console connected to the DI box XLR output.
Figure 5: Example Connection to Console (DI Box rear panel shown)

Guitar Setup: Connect your guitar to the 1/4" INPUT. Use the 1/4" PARA OUT to connect to your guitar amplifier for monitoring. The XLR BALANCED OUTPUT connects to a channel on your mixing console.

Keyboard Stereo Setup: For a stereo keyboard, connect the Left output of the keyboard to Channel 1 INPUT and the Right output to Channel 2 INPUT. Connect the respective XLR BALANCED OUTPUTs to two separate channels on your mixing console (e.g., Channel 1 for Left, Channel 2 for Right). Adjust panning on the mixer for stereo imaging.

5. Operation

  1. Connect Your Instrument: Plug your instrument's 1/4" output into the DI120's 1/4" INPUT jack for the desired channel.
  2. Connect to Amplifier (Optional): If you wish to monitor your sound through an instrument amplifier, connect the DI120's 1/4" PARA OUT to your amplifier's input.
  3. Connect to Mixer/PA: Connect the DI120's XLR BALANCED OUTPUT to an available XLR input on your mixing console or PA system.
  4. Set Attenuation: Select the appropriate attenuation (0dB, -20dB, or -40dB) using the switch on the front panel. Start with 0dB and reduce if the signal is too hot and causing distortion.
  5. Ground Lift: If you experience hum or buzz, toggle the GROUND switch on the rear panel. The "Lift" (OFF) position often resolves ground loop issues. If no noise is present, leave it in the "ON" position.
  6. Adjust Levels: Gradually increase the gain on your mixing console for the DI box channel until the desired level is achieved.

6. Troubleshooting

  • Hum or Buzz: If you hear unwanted hum or buzz, try engaging the GROUND LIFT switch (set to OFF). This often resolves ground loop issues.
  • Distorted Sound: If the sound is distorted, the input signal might be too hot. Try engaging the -20dB or -40dB ATTENUATION switch on the front panel to reduce the signal level.
  • No Sound:
    • Check all cable connections to ensure they are secure.
    • Verify the input source (instrument) is working correctly.
    • Ensure the correct input channel is selected and gain is appropriately set on your mixer/PA.

7. Technical Specifications

Feature Specification
Item Type Microphone Amplifier (Note: This product functions as a Direct Box)
Channels 2 (Dual Channel)
Type Passive Direct Box
Input Impedance 50K Ohms (1/4" TS Input)
Output Impedance 600 Ohms (XLR Balanced Output)
Attenuation 0dB, -20dB, -40dB (Switchable)
Ground Lift Yes (Switchable ON/OFF)
Dimensions (L x W x H) 22 cm x 10 cm x 8 cm (Approximate package dimensions)
Weight 1.0 kg (Approximate package weight)
Construction Heavy-duty metal casing

8. Maintenance

  • Cleaning: Clean the unit with a soft, dry cloth. Do not use abrasive cleaners, solvents, or corrosive detergents.
  • Storage: Store the DI box in a dry, cool place away from direct sunlight and extreme temperatures.
  • Handling: Avoid dropping the unit or subjecting it to strong impacts to prevent damage.

9. User Tips

  • Always connect and disconnect cables with the audio system turned off or muted to prevent pops and potential damage to speakers.
  • Experiment with the attenuation settings to find the optimal level for your specific instrument and mixer input.
  • If using a stereo instrument like a keyboard, utilize both channels of the DI120 for a full stereo image.

10. Warranty and Support

This product comes with a warranty card. Please refer to the included "Products Warranty Card" for detailed information regarding warranty terms and conditions. For any service or support inquiries, please contact your local dealer or the manufacturer directly.

11. Product Overview Video

Watch this video for an unboxing and overview of the Alctron DI120 Dual Channel Passive Direct Box, demonstrating its features and connectivity.

Video: Unboxing and feature overview of the Alctron DI120.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.