NISSEI RS-50

Contents

NISSEI RS-50 Digital SWR Watt Meter

Instruction Manual

Introduction

The NISSEI RS-50 is a compact and easy-to-use digital SWR (Standing Wave Ratio) and Watt meter designed for measuring forward power, reflected power, and SWR in VHF/UHF radio systems. It features a clear LED backlight display and a convenient control layout, making it an essential tool for radio enthusiasts and professionals.

Key Features

  • Forward/Reversed/VSWR ratio measurement with a single button.
  • LED backlight display for easy reading in various lighting conditions.
  • Flexible power options: internal AAA batteries or external Micro USB port.
  • Compatible with rechargeable batteries (alkaline, Ni-Ca, Ni-MH).
  • Micro USB-DC 5V input (adapter not included).
  • User-friendly control layout for straightforward operation.

Specifications

ParameterDetail
ModelRS-50
Frequency Range125-525 MHz (Optimal test results: 140-150 MHz and 430-450 MHz)
Center Calibrated145 MHz (VHF), 435 MHz (UHF)
Power Range0-120W (±5% accuracy)
Testing FunctionsForward Power (Fwd), Reversed Power (Rev), SWR
Insertion Loss0.3 dB or lower
Impedance50 ohm
Power Source2 x AAA batteries or Micro USB port
Connector Type"M" type (UHF/PL-259) or "N" type
Dimensions70W x 78H x 30D mm
Net Weight220g (without batteries)
Detailed instruction manual page showing features, specifications, measurement, and battery installation.
Figure 1: Detailed specifications and instructions from the manual.

Setup

Battery Installation

  1. Remove the black screw from the cover to open the rear panel of the unit.
  2. Install 2 pieces of "AAA" batteries into the battery compartment.
  3. The unit can be powered by either alkaline or Ni-Ca/Ni-MH rechargeable batteries.
  4. Important: This unit does not have built-in charging circuitry. Do not attempt to charge rechargeable batteries while they are inside the unit.
  5. Ensure correct battery polarity during installation.
  6. If the unit will not be used for an extended period, remove the batteries to prevent leakage and damage.
Angled view of the RS-50 SWR Watt Meter showing the power and light switches, and the TX and ANT connectors.
Figure 2: Front view of the RS-50, highlighting the power switch and connectors.

Connecting the Meter

  1. Connect the output of your transceiver (radio) to the "TX" port on the RS-50 meter.
  2. Connect your antenna or a dummy load to the "ANT" port on the RS-50 meter.
  3. Ensure all connections are secure to prevent signal loss or damage.
Front view of the NISSEI RS-50 Digital SWR Watt Meter with its display showing 'FWD', 'REF', and 'SWR' readings, and 'TX' and 'ANT' ports.
Figure 3: Front panel of the RS-50 showing TX and ANT connectors.

Operating Instructions

  1. After connecting the transceiver and antenna/load, switch the "POWER" button to "ON" to activate the unit.
  2. The LCD display will simultaneously show "Fwd" (Forward Power), "Rev" (Reflected Power), and "SWR" readings.
  3. To activate the backlight, switch the "LIGHT" button to "ON".
  4. The backlight will automatically turn off after 30 seconds of inactivity to conserve power.
  5. When the PTT (Push-To-Talk) button on your transceiver is pressed, the backlight will reactivate.
Front view of the NISSEI RS-50 Digital SWR Watt Meter with its display showing example 'FWD', 'REF', and 'SWR' readings.
Figure 4: Display showing typical SWR and power readings.

Maintenance

  • Keep the device clean and dry. Avoid exposure to moisture, dust, and extreme temperatures.
  • Do not use harsh chemicals or abrasive cleaners on the unit. A soft, damp cloth is sufficient for cleaning.
  • As mentioned in battery installation, remove batteries if the unit will not be used for a long period to prevent corrosion.
  • Store the meter in a safe place to prevent physical damage.

Troubleshooting

No display or unit does not power on:
  • Check if batteries are correctly installed with the right polarity.
  • Replace old batteries with new ones.
  • Ensure the "POWER" switch is in the "ON" position.
  • Try powering the unit via the Micro USB port with a compatible 5V power source (adapter not included).
Backlight not working:
  • Ensure the "LIGHT" switch is in the "ON" position.
  • The backlight automatically turns off after 30 seconds of no PTT activity. It will reactivate when PTT is pressed.
Inaccurate readings:
  • Ensure all cable connections (transceiver to TX, antenna/load to ANT) are secure and of good quality.
  • Verify that the operating frequency is within the optimal range of the meter (140-150 MHz and 430-450 MHz for best results).
  • Check the condition of your antenna and cables.

User Tips

  • This device is a measurement tool for SWR and power, not a signal booster or reception enhancer. If you are experiencing bad reception, this meter can help diagnose antenna system issues but will not directly improve reception.
  • The RS-50 is available with either "M" type (UHF/PL-259) or "N" type connectors. Ensure you have the correct connector type for your equipment.
  • For optimal accuracy, especially for SWR measurements, ensure your radio system is properly tuned and matched.

Warranty and Support

For any issues not covered in this manual, or for warranty claims, please contact your retailer or the manufacturer's customer support. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.