XK K123

Contents

XK K123 6CH Brushless AS350 Scale RC Helicopter User Manual

Model: K123

1. Introduction

This manual provides detailed instructions for the safe and effective operation, maintenance, and troubleshooting of your XK K123 6CH Brushless AS350 Scale RC Helicopter. The XK K123 is a high-simulation model based on the AS350 (Little Squirrel) prototype, featuring a unique three-rotor blade flybarless design and advanced 3D/6G flight modes.

XK K123 RC Helicopter, remote controller, battery, brushless motor, and USB charger
XK K123 RC Helicopter with accessories.

2. Package Contents

Please check the package contents carefully upon unboxing to ensure all items are present and undamaged:

  • 1 x K123 RC Helicopter
  • 1 x Transmitter (Remote Controller)
  • 3 x Main Blades
  • 1 x Tail Blade
  • 1 x Main Gear
  • 1 x USB Charger
  • 2 x Li-po Batteries (3.7V 500mAh 25C)
  • 1 x Screwdriver
  • 1 x Hex Wrench
  • 1 x Operating Instructions Manual (this document)
XK K123 RC Helicopter, remote, manual, blades, USB cable, batteries, and tools laid out
All components included in the package.

3. Setup

3.1. Charging the Battery

Before first use, fully charge the Li-po batteries. Use only the dedicated USB charger provided. The charger is designed to charge two batteries simultaneously.

  • Connect the USB charger to a suitable USB power source (e.g., computer USB port, USB wall adapter).
  • Connect the Li-po batteries to the charger.
  • Charging time is approximately 30-60 minutes per battery.
  • Ensure the batteries are fully charged before attempting flight.
Close-up of the helicopter's brushless motor and battery
High efficient brushless motor and high discharge rate battery.

3.2. Transmitter Setup

The transmitter is a 6-channel remote control with a large LCD display and low voltage alarm function. It supports both Mode 1 and Mode 2, which can be switched as needed.

  • Install batteries into the transmitter (batteries for the transmitter are not included).
  • Power on the transmitter.
  • The transmitter features a 3D special IDLE switch and a throttle hold (TH.HOLD) switch.
  • You can adjust the hovering point settings by entering the setting mode on the transmitter.
  • The communication protocol is compatible with FUTABA S-FHSS.
Front view of the XK K123 remote controller
XK K123 Remote Controller.
Diagram showing the 6CH transmitter with features like 3D, IDLE, TH HOLD, LCD, and low voltage alarm
6CH Transmitter features.
Diagram showing compatibility with FUTABA S-FHSS
FUTABA S-FHSS compatibility.

4. Operating Instructions

4.1. Flight Modes: 3D and 6G

The XK K123 helicopter offers two distinct flight modes, 3D and 6G, which can be switched freely via the remote controller:

  • 3D Mode: Utilizes a 3-axis gyroscope for sensitive reaction, enabling stunt flying such as rolling, inverted flight, side flight, and hurricane flying. This mode is suitable for intermediate to expert pilots.
  • 6G Mode: Utilizes a 6-axis gyroscope for enhanced flight stability, making it especially suitable for beginners.
Illustration comparing 3D mode for aerobatics with 6G mode for stable flight
3D and 6G flight modes explained.

4.2. Basic Flight Controls

Familiarize yourself with the basic controls on the transmitter:

  • Throttle: Controls the main rotor speed and altitude.
  • Elevator (Pitch): Controls forward and backward movement.
  • Aileron (Roll): Controls sideways movement (left and right).
  • Rudder (Yaw): Controls the helicopter's rotation around its vertical axis.

Always start in 6G mode for stable flight, especially if you are a beginner. Practice hovering and gentle movements before attempting more advanced maneuvers.

4.3. Advanced Maneuvers

Once comfortable with basic flight in 6G mode, you can switch to 3D mode to perform aerobatics. Ensure you have ample space and are away from obstacles when practicing advanced maneuvers.

Video demonstrating the XK K123 helicopter performing various flight maneuvers and stunts, including flying over water and waterfalls.

5. Maintenance

Regular maintenance ensures the longevity and optimal performance of your helicopter.

5.1. General Care

  • Keep the helicopter clean and free from dust and debris.
  • Avoid exposing the helicopter to moisture or extreme temperatures.
  • Inspect all parts for damage before and after each flight.

5.2. Battery Care

  • Always use the provided USB charger for charging.
  • Do not overcharge or over-discharge the batteries.
  • Store batteries in a cool, dry place away from direct sunlight.
  • If the battery swells or shows signs of damage, discontinue use immediately.

5.3. Blade Replacement

The package includes spare main and tail blades. If any blades become damaged during flight, replace them promptly using the provided tools to maintain flight stability and safety.

Close-up of the internal electronics and wiring of the XK K123 helicopter
Internal electronics of the helicopter.

6. Troubleshooting

If you encounter issues with your helicopter, refer to the following common problems and solutions:

  • Helicopter does not respond to controls: Ensure the transmitter batteries are charged and correctly installed. Verify the helicopter battery is fully charged and properly connected. Re-bind the helicopter to the transmitter if necessary.
  • Unstable flight: Check for damaged blades or other components. Ensure the helicopter is in 6G mode for stable flight, especially if you are a beginner. Calibrate the gyroscope if flight remains unstable.
  • Short flight time: Ensure batteries are fully charged before each flight. Battery performance can degrade over time; consider replacing old batteries.
  • Motor not spinning: Check all connections. If the motor is damaged, it may need replacement.

7. Specifications

FeatureSpecification
Model NumberK123
TypeHELICOPTER (6CH flybarless three blades)
Dimensions238mm (length) * 77mm (height), 244mm (main rotor diameter)
Flying Weight79.5g
Motor1106 11000KV brushless main motor, 8502 coreless tail motor
Battery3.7V 500mAh 25C Li-Po (2 included)
Flight TimeApprox. 5 minutes
Charging Time30-60 minutes
Charging Voltage3.7V
Control Channels6 channels
Remote Distance150M
Controller ModeMODE1, MODE2 (switchable)
MaterialMetal, Plastic, Rubber
State of AssemblyReady-to-Go
Remote ControlYes
Is Batteries IncludedYes (for helicopter)
Controller BatteryNot Included
Video Capture ResolutionOther (No integrated camera)
Camera Mount TypeOther (No dedicated mount)
Aerial PhotographyNo
Indoor/Outdoor UseOutdoor
Operator Skill LevelIntermediate, Expert
Recommend Age14+ years
WarningNot suitable for age 14 years old (contradicts Recommend Age, user discretion advised)
CertificationCE
High-concerned chemicalNone
Is ElectricLithium battery
Plugs TypeUSB Cable
Package Weight1.200kg (2.65lb.)
Package Size40cm x 30cm x 18cm (15.75in x 11.81in x 7.09in)
Diagram showing detailed specifications and package contents of the XK K123 helicopter
Detailed specifications and package contents.

8. User Tips

Based on common user inquiries, here are some tips for an optimal experience:

  • Battery Life Expectation: The helicopter has a flight time of approximately 5 minutes. It's recommended to have both included batteries fully charged for extended play sessions.
  • Beginner Flying: Always start in 6G mode for maximum stability. This mode is designed to assist new pilots in learning the controls without the added complexity of 3D aerobatics.
  • Transmitter Modes: If you find the controls feel reversed or unusual, check if the transmitter is set to the correct Mode (Mode 1 or Mode 2) that you are accustomed to. The transmitter allows switching between these modes.

9. Warranty and Support

9.1. Manufacturer's Warranty

The XK K123 RC Helicopter comes with a 12-month limited manufacturer's warranty for defective items, starting from the date of receipt. This warranty does not cover items damaged due to misuse or accidents. Accessories are covered by a 3-month warranty.

For warranty claims, please retain your proof of purchase and contact the seller or manufacturer with your order number and a detailed description of the defect.

9.2. Product Support

For any questions, technical assistance, or support not covered in this manual, please contact the seller or manufacturer's customer service. Refer to your purchase documentation for specific contact details.

© 2024 XK. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.