1. Safety Warnings
- Before installation, park the motorcycle on a flat surface, support the main stand, and turn off the power to prevent the vehicle from tipping over and causing injury.
- This rearview mirror is an auxiliary tool for observing road conditions behind. Always turn your head to look directly before turning or changing lanes; do not rely entirely on the mirror.
- The mirror surface is made of glass. If cracks or damage appear, stop using it immediately to avoid injury from flying fragments.
- After installation, ensure the bracket is securely fastened. No looseness or shaking should occur during riding, as this will impair visibility and cause danger.
- Convex mirrors (if applicable) make objects appear farther away than they actually are. Use extra caution when judging distances for lane changes.
2. Setup and Installation
Tools Required:
- Phillips screwdriver
- Wrench (select according to screw specifications)
Installation Process:
- Remove the original mirror: Use a wrench to unscrew the original mirror from the motorcycle handlebar, and clean any dust and oil from the mounting holes.
- Check accessories: Verify that the gaskets, screws, and bracket base in the accessory package match those shown in the image, ensuring nothing is missing.
- Secure the base: Align the mirror base with the mounting holes on the motorcycle handlebar, place a rubber gasket underneath, and hand-tighten the screws initially to avoid thread stripping.
- Install the mirror: Align the mirror bracket with the base interface, rotate and tighten it to ensure a tight connection.
- Preliminary angle adjustment: Sit in the standard riding position, rotate the mirror and bracket to adjust the angle so that the rear road surface is clearly visible.
- Final tightening: Use a wrench to fully tighten all screws, ensuring no looseness or shaking during riding.
- Installation check: Gently shake the mirror by hand to confirm it is securely fastened and the angle is stable; installation is complete.
Image: Included mounting hardware for installation.
3. Operating Instructions
Mirror Adjustment Method:
- Maintain a normal riding posture, hold the handlebars with both hands, and look straight ahead at the road.
- Left mirror: Rotate the mirror so that the horizon is in the top 1/3 of the mirror, clearly covering the left rear lane and roadside conditions.
- Right mirror: Rotate the mirror so that the horizon is in the center of the mirror, clearly covering the right rear and adjacent lane conditions.
Video: Demonstrates the adjustability and range of motion of the mirrors.
After adjustment, double-check that the bracket is secure to ensure the angle does not shift due to vibration during riding.
4. Maintenance and Care
- Daily cleaning: Wipe the mirror surface with a soft cloth (e.g., eyeglass cloth) dampened with clean water or a neutral detergent. Do not use rough cloths, steel wool, or alcohol, as these may scratch the coating.
- Regular inspection: Every 500 km or monthly, check if the bracket screws are loose and if the mirror has cracks or scratches. Tighten or replace as needed.
- Storage protection: When the motorcycle is not in use for an extended period, cover the mirror with a dust cloth to prevent aging of the mirror housing and fading of the mirror surface due to sun exposure.
5. Troubleshooting
| Fault Phenomenon | Possible Cause | Solution |
|---|---|---|
| Mirror shaking or loose | Bracket screws not tightened / Thread stripping at interface | Retighten screws; replace bracket or interface nut if threads are stripped |
| Blurred vision or double images | Mirror surface soiled / Coating damaged | Wipe with neutral detergent; replace mirror if coating is damaged |
| Mirror cracked or chipped | External impact / Material aging | Replace the entire mirror immediately; do not replace only the mirror surface |
| Unable to install / Interface mismatch | Incorrect thread specification / Foreign objects in interface | Confirm vehicle mounting hole positions and replace with appropriate accessories; clear foreign objects from interface |
6. Specifications
| Model Name | F142 |
| Brand Name | LMoDri |
| Color | Black |
| Item Type | Side Mirrors & Accessories |
| Material | ABS plastic (Mirror Head Cover) & Aluminium Rod (Mirror Rod) |
| Item Length | 32 cm |
| Item Width | 8.8 cm |
| Item Weight | 580g (for the pair) |
| Installment Screw Sizes | 8mm & 10mm (Clockwise and Counter-clockwise threads included) |
Image: Key dimensions of the rearview mirrors.
7. User Tips
- These mirrors offer a wider viewing angle compared to many traditional mirrors, enhancing visibility.
- Users report minimal vibration, contributing to a clearer reflection during rides.
- Always double-check the thread direction required for your specific motorcycle model, as some bikes (e.g., certain Kawasaki Z1000 models) may require reverse threads. The package includes various screw types to accommodate different needs.
- The mirrors are adjustable, allowing riders to customize their viewing angle for optimal rear visibility.
8. Warranty and Support
For warranty information, technical support, or any product-related inquiries, please refer to your purchase documentation or contact the seller directly.
A detailed user manual in PDF format may also be available for download from the seller's product page: View PDF Manual