SUNSUN HW-602, HW-603, HW-602B, HW-603B, LW-602, LW-603, LW-602B, LW-603B

Contents

SUNSUN Aquarium External Filter Instruction Manual

Models: HW-602, HW-603, HW-602B, HW-603B (SUNSUN) | LW-602, LW-603, LW-602B, LW-603B (JIALU)

1. Introduction

Thank you for choosing the SUNSUN/JIALU Aquarium External Filter. This ultra-quiet external filter bucket is designed to provide efficient mechanical, chemical, and biological filtration for your aquarium, ensuring a clean and healthy environment for your aquatic life. This manual provides detailed instructions for the safe installation, operation, and maintenance of your filter.

2. Safety Information

  • Ensure the filter is placed on a stable, level surface below the aquarium.
  • Always disconnect power before performing any maintenance or cleaning.
  • Do not operate the filter if the power cord or plug is damaged.
  • This product is certified with CE for safety.
  • Ensure all connections are secure to prevent leaks.
  • Keep out of reach of children.

3. Package Contents

Please check the package for the following components. Note that HW-602 and HW-603 models do not include a water pump, water pipes, or import/export pipes and cannot be used alone.

External filter unit with hoses, filter media, and various pipe accessories
Figure 1: Complete filter package contents (HW-602B/603B shown)
  • Filter Shell
  • Pump (included with HW-602B/603B models)
  • Regulating Valve
  • Upper Treatment Board
  • Filter Sponge (multi-layered)
  • Lower Treatment Board
  • Inlet Pipe
  • Universal Outlet Pipe
  • Perforated Outlet Pipe (Spray Bar)
  • Rubber Tube (Hoses)
  • Suction Cups and Connectors
Exploded view diagram of the filter and its accessories with numbered parts
Figure 2: Exploded view of filter components

4. Specifications

FeatureHW-602BHW-603BHW-602 / HW-603
Rated Voltage110V-220V110V-220VN/A (No pump)
Rated Frequency50Hz / 60Hz50Hz / 60HzN/A
Pump Power6W6WN/A
Maximum Lift0.85M0.85MN/A
Maximum Flow400L/H400L/HN/A
Outlet Diameter12mm12mmN/A
Total Weight1.5KG1.7KGN/A
Dimensions (LxWxH)140 * 140 * 255mm165 * 165 * 295mmHW-602: 205*160mm, HW-603: 240*180mm
Aquarium SuitabilityUp to 150 litersUp to 200 litersRequires external pump/hoses
Hose Diameter (HW-602/603)N/AN/A16mm
Specifications table for HW-602B and HW-603B, including dimensions and pump details.
Figure 3: Detailed specifications for HW-602B and HW-603B
Size comparison image for HW602B and HW603B, showing overall height and width.
Figure 4: Size comparison of HW602B and HW603B models

5. Setup Instructions

Follow these steps carefully for proper installation:

  1. Open the Filter Unit: Open the 4 clamps in the direction of the arrow shown in Picture 1 (refer to Figure 5, step 1), to separate the clamps from the lid (Figure 5, step 2).
  2. Remove the Lid: Press and hold the barrel with one hand, grasp the water outlet with the other, and pull up to separate the lid from the barrel (Figure 5, step 3).
  3. Install Filter Media: If the filter cotton in the barrel is not needed, you can place other suitable filter materials according to your requirements. After installing the filter material, ensure the filter plate is installed correctly, in the opposite direction to the bottom of the filter plate (Figure 5, step 4). Close the lid and press it flat until the lid and body are completely sealed. Fasten the 4 clasps (Figure 5, step 5).
  4. Install Regulating Valve: Install the water inlet regulating valve onto the elbow of the water inlet on the barrel cover, and tighten the fixing nut (Figure 5, step 6). Ensure the rubber sealing ring on the valve seat joint is properly installed (Figure 5, step 7).
  5. Connect Hoses and Prime: Connect the outlet pipe first. Add approximately 3/4 of the water into the filter bucket. Then, connect all components according to the installation diagram (Figure 6). Turn on the power. Ensure both the inlet and outlet water regulating valves are open. If no water comes from the outlet, lift the filter bucket until water comes out and there is no air in the inlet pipe, then place the bucket back down.
  6. Regulating Valve Operation: Refer to Figure 5, step 8 for the on-off state of the water inlet regulating valve.
English instructions for HW Series filter, showing 8 steps with diagrams for assembly and priming.
Figure 5: Step-by-step assembly and priming instructions
Schematic diagram of filter installation with inlet/outlet pipes and flow trend diagram.
Figure 6: Installation schematic and water flow diagram
Detailed view of outlet pipe components with dimensions.
Figure 7: Outlet pipe components (e.g., spray bar)
Detailed view of inlet pipe components with dimensions.
Figure 8: Inlet pipe components

6. Operating Instructions

  • Power On: After successful installation and priming (ensuring no air in the system), plug in the filter to start operation.
  • Flow Regulation: The regulating valve allows you to adjust the water flow. Turn the switch to 'Open' for maximum flow and 'Close' to reduce or stop the flow.
  • Continuous Operation: For optimal aquarium health, the filter should run continuously.
  • Aeration: This external filter does not provide built-in aeration. If aeration is required for your aquarium, consider positioning the perforated outlet pipe (spray bar) above the water surface to create surface agitation, or use a separate air pump.
Close-up of the pump (JP-450G) with specifications and the flow regulating switch.
Figure 9: Pump details and flow regulating switch

Video 1: Product demonstration and assembly overview

7. Maintenance

Regular maintenance is crucial for the longevity and efficiency of your filter.

  • Cleaning Filter Media: Periodically check and clean the filter sponges. The frequency depends on your aquarium's bioload. Always use old aquarium water to rinse media to preserve beneficial bacteria.
  • Replacing Filter Media: Filter cotton should be replaced when it becomes too clogged to clean effectively. You can also replace or add other filter materials like bio balls or ceramic rings for enhanced biological filtration.
  • Pump Maintenance: Inspect the pump impeller for any debris or blockages during cleaning.
  • Seal Inspection: Check the rubber sealing ring on the lid and valves for wear and tear. Replace if necessary to prevent leaks.
Diagram illustrating the internal flow of water through different filter media layers.
Figure 10: Water flow through filter media layers
Image showing filter media options like bio balls and how they can be used for biological filtration.
Figure 11: Example of biological filter media

8. Troubleshooting

  • No Water Flow / Low Flow:
    • Ensure the filter is properly primed. Air in the system can significantly reduce or stop flow. Lift the filter bucket until water flows smoothly from the outlet, indicating air has been expelled.
    • Check if filter media is clogged. Clean or replace as necessary.
    • Verify that the inlet and outlet regulating valves are fully open.
    • Inspect the pump impeller for blockages.
  • Noisy Operation:
    • Air trapped in the filter can cause gurgling or humming noises. Re-prime the filter to remove air.
    • Ensure the filter is placed on a soft, stable surface (e.g., a piece of linoleum) to absorb vibrations.
    • Check the pump impeller for any foreign objects or damage.
  • Difficulty Connecting Hoses:
    • To connect hoses to fittings, first push the hose onto the fitting, then tighten the nut over it. This provides a secure and leak-free connection.
  • Leaks:
    • Check all hose connections and ensure they are tight.
    • Inspect the main O-ring seal on the filter head and the seals on the regulating valves for proper seating and damage.

9. User Tips

  • For aquariums up to 200 liters, the HW603B model is generally recommended for better performance.
  • If you require stronger flow for larger tanks or specific setups, consider upgrading the pump.
  • Transparent models (JIALU LW series) allow for easy visual inspection of the filter media's cleanliness, helping you determine when maintenance is needed.
  • Enhance biological filtration by replacing some filter cotton with bio balls or ceramic rings. These provide more surface area for beneficial bacteria.
  • Ensure the filter bucket is filled with water and all air is removed from the system before starting the pump to prevent airlocks and ensure optimal flow.

10. Warranty and Support

For warranty claims, technical support, or replacement parts, please contact your retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.