HobbyWing QuicRun 1060 1625 0880

Contents

HobbyWing QuicRun Waterproof Brushed Electronic Speed Controller User Manual

Models: QuicRun WP-880, 1060, 1625

1. Introduction

This manual provides essential information for the proper setup, operation, maintenance, and troubleshooting of your HobbyWing QuicRun Waterproof Brushed Electronic Speed Controller (ESC). The QuicRun series ESCs are designed for various RC vehicles, including touring cars, buggies, short course trucks, monsters, truggies, rock crawlers, and tanks. Please read this manual thoroughly before using your ESC to ensure safe and optimal performance.

Product overview video for the HobbyWing QuicRun ESC.

2. Safety Precautions

  • Always disconnect the battery from the ESC when not in use to prevent accidental operation and potential damage.
  • Ensure all connections are secure and correctly polarized before powering on the system. Incorrect wiring can cause severe damage to the ESC, motor, and battery.
  • Keep the ESC away from water and moisture, even though it is waterproof. After use in wet conditions, clean and dry the ESC thoroughly to prevent corrosion of connectors.
  • Avoid operating the ESC in extreme temperatures. Overheating can lead to permanent damage.
  • Use only batteries and motors that are compatible with the ESC's specifications. Exceeding voltage or current limits will damage the unit.
  • Keep hands and loose clothing away from rotating parts of the RC vehicle during operation.

3. Product Overview & Features

The HobbyWing QuicRun series offers robust and reliable brushed ESCs with several advanced features:

  • Waterproof Design: Fully waterproof and dust-proof for all-weather conditions. (Note: Clean and dry after use to prevent rusty connectors).
  • Efficient Heat Dissipation: Patented copper heat-conductive plates transfer internal heat to the aluminum heat sink (WP-880).
  • Built-in BEC: Integrated Switch-Mode BEC for reliable power to receiver and servos.
  • Tunable Parameters: Adjustable drag brake, drag brake rate, PWM frequency, acceleration/punch, and proportional brake (WP-880).
  • Multiple Running Modes: Supports Fwd/Br, Fwd/Rev/Br, and Fwd/Rev modes for various vehicle types.
  • Automatic Throttle Calibration: Easy setup with automatic throttle range calibration.
  • Multiple Protections: Includes low voltage cut-off, thermal protection, and throttle signal loss protection.
  • Easy Programming: Parameters can be set via jumpers (1060/1625) or a separate LED program card (WP-880).
Multiple views of the HobbyWing QuicRun ESC

Multiple views of the HobbyWing QuicRun ESC, showcasing its design and wiring.

HobbyWing QuicRun ESC with included accessories

HobbyWing QuicRun ESC with included accessories such as stickers, heat shrink tubing, and zip ties.

4. Specifications

HobbyWing QuicRun WP-880 80A Brushed ESC

Feature Specification
ModelQuicRun WP 880 dual brushed
Cont./Peak Current80A/400A
Motor TypeBrushed motor (540/550/775 size motors)
ApplicationsVarious 1/10 & 1/8 Vehicles
Motor Limit (2S Lipo/6S NiMH)>=12T or RPM<30000--7.4V (540/550 size motors)
Motor Limit (3S Lipo/9S NiMH)>=18T or RPM<20000--7.4V (540/550 size motors)
Motor Limit (4S Lipo/12S NiMH)>=24T or RPM<15000--7.4V (540/550 size motors)
Lipo/NiMH CELLs2-4S Lipo or 5-12S NiMH
BEC Output6V/4A (Switch-Mode)
Connectors (Input End)No Connectors
Connectors (Output End)4.0mm Female Bullet Connectors
Size/Weight (w./Wires)45.9*34.7*26.5mm/75g
Programming PortSeparate Port

HobbyWing QuicRun 1060 60A Brushed ESC

Feature Specification
ModelQuicRun-WP-1060-BRUSHED
Fwd. Cont./Peak Current60A/360A
Rev. Cont./Peak Current30A/180A
Voltage Range2-3S Lipo or 5-9 NiMH
Cars Applicable1/10: Touring Car, Buggy, Short Course Truck, Monster, Truggy, Rock Crawler and Tank
ResistanceFwd 0.001Ω, Rev 0.002Ω
BEC Output3A/6V (Switch Mode)
Dimension/Weight36.5x32x18mm / 39 g
Cooling FanWithout cooling fan
Running ModesForward / Reverse / Brake, Forward / Brake, Forward / Reverse
Motor Limit (2S Lipo or 6 NiMH)540 or 550 Size Motor: ≥12T or RPM<30000 @7.2V
Motor Limit (3S Lipo or 9 NiMH)540 or 550 Size Motor: ≥18T or RPM< 20000 @7.2V

HobbyWing QuicRun 1625-25A Brushed ESC

Feature Specification
ModelQuicRun-WP-1625-BRUSHED
Fwd. Cont./Peak Current25A/100A
Rev. Cont./Peak Current25A/100A
Voltage Range2-3S Lipo or 5-9 NiMH
Cars Applicable1/18 & 1/16 Touring Car/Buggy/Monster/Truggy
ResistanceFwd 0.003Ω, Rev 0.003Ω
BEC Output1A/6V (Linear Mode)
Dimension/Weight34x24x14mm/23.5g
Running ModesForward/Reverse/Brake

5. Setup

Follow these steps to set up your HobbyWing QuicRun ESC:

  1. Connect to Motor: Connect the ESC's motor wires to your brushed motor. Ensure correct polarity if specified by your motor.
  2. Connect to Battery: Connect the ESC's power input wires to your battery pack. Double-check polarity to avoid damage.
  3. Connect to Receiver: Plug the ESC's throttle cable (usually a 3-wire servo plug) into the throttle channel (CH2) of your RC receiver.
  4. Throttle Range Calibration: Perform throttle range calibration according to your radio system's instructions. This ensures the ESC correctly interprets your transmitter's throttle signals.
  5. Programming (WP-880): For the WP-880 model, connect the optional LED program card to the separate programming port on the ESC to adjust parameters.
  6. Programming (1060/1625): For 1060 and 1625 models, use the onboard jumpers to set the ESC parameters. Refer to the specific model's instructions for jumper configurations.
HobbyWing QuicRun ESC with motor and battery wires connected

Illustration of the HobbyWing QuicRun ESC with motor and battery wires connected, ready for installation.

6. Operating Modes

The QuicRun ESCs support different running modes to suit various RC applications:

  • Fwd/Br (Forward/Brake): This mode allows forward movement and braking. It is typically used for racing or applications where reverse is not desired or needed.
  • Fwd/Rev/Br (Forward/Reverse/Brake): This is the most common mode, allowing forward, reverse, and braking functions. It's suitable for general bashing and recreational driving.
  • Fwd/Rev (Forward/Reverse): This mode allows forward and reverse movement without a dedicated brake function. (Note: QUICRUN-WP-1625-BRUSHED ESC only has the Fwd / Rev / Br mode, so this mode may not be available on all models).

7. Programming & Parameter Settings

Adjusting ESC parameters allows you to fine-tune its performance for your specific vehicle and driving style.

For WP-880 80A ESC (using LED Program Card)

The WP-880 ESC features a separate programming port for easy connection to an LED program card. This card allows you to adjust various parameters:

  • Running Mode
  • LiPo Cells
  • Low Voltage Cutoff Threshold
  • ESC Thermal Protection
  • Motor Thermal Protection
  • Motor Rotation
  • BEC Voltage
  • Max. Brake Force
  • Max. Reverse Force
  • Start Mode (Punch)
  • Drag Brake
HobbyWing LED Program Card with settings table

HobbyWing LED Program Card displaying various programmable parameters and their values.

For 1060 60A and 1625 25A ESCs (using Jumpers)

These models use jumpers for parameter settings. Refer to the specific model's manual or the markings on the ESC for jumper configurations to adjust settings like running mode, battery type, and cut-off voltage.

8. Maintenance

  • Cleaning: After use, especially in dusty or wet conditions, clean the ESC with a soft brush or compressed air. If used in water, ensure it is thoroughly dried to prevent corrosion.
  • Inspection: Regularly inspect all wires, connectors, and the ESC casing for any signs of damage, wear, or loose connections.
  • Storage: Store the ESC in a dry, cool place away from direct sunlight and extreme temperatures.
  • Firmware: Keep an eye on the manufacturer's website for any firmware updates that might improve performance or address issues.

9. Troubleshooting

If you encounter issues with your ESC, consider the following common problems and solutions:

  • ESC Not Powering On:
    • Check battery connection and charge level.
    • Verify all wiring is correct and secure.
  • Motor Not Responding or Erratic Behavior:
    • Ensure throttle range calibration is correctly performed.
    • Check motor connections and ensure the motor is not damaged.
    • Verify the receiver is powered and receiving signals from the transmitter.
  • ESC Overheating:
    • Check motor limits against the ESC specifications. Using a motor with too low a turn count or too high RPM can cause overheating.
    • Ensure adequate airflow around the ESC.
    • Reduce the load on the motor/vehicle if possible.
  • ESC Burning Out (Repeatedly):
    • This often indicates exceeding the ESC's voltage or current limits. Double-check your battery type (e.g., LiPo vs. Li-ion) and cell count against the ESC's specifications.
    • Ensure the motor is compatible and not drawing excessive current.
    • Inspect for short circuits in the wiring or motor.
  • No Reverse Function:
    • Check the ESC's running mode setting. Ensure it is set to Fwd/Rev/Br or Fwd/Rev.

10. User Tips

  • For rock crawlers, if you desire a strong drag brake, ensure the drag brake setting is appropriately configured (e.g., remove the jumper on some models or adjust via program card).
  • The ESC provides a smooth start and reliable auto-brake, which is beneficial for vehicles like crawlers on inclines.
  • While the ESC supports Ni-MH batteries, always verify the voltage and cell count are within the specified range for your particular ESC model.

11. Warranty and Support

For technical assistance, warranty claims, or further information, please contact the manufacturer or your authorized dealer. Keep your proof of purchase for any warranty-related inquiries.

© 2023 HobbyWing. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.