YHDC SCT016T-D

Contents

YHDC SCT016T-D Split Core Current Transformer

Instruction Manual

1. Product Overview

The YHDC SCT016T-D is a split core current transformer designed for non-invasive measurement of AC current. It provides galvanic separation between the primary AC current circuit and the secondary DC output circuit, ensuring safety and reliability. This device is ideal for applications requiring current monitoring without interrupting the main circuit.

YHDC SCT016T-D Split Core Current Transformer showing input/output specifications
Figure 1: YHDC SCT016T-D Product Overview with key specifications.

The transformer features a safety lock buckle for easy installation and a built-in rectifier with screw terminal output. It is available in various input current ratings (30A, 50A, 60A, 80A, 100A) and corresponding voltage outputs (1V, 3V, 5V DC) with an accuracy of 1%.

2. Setup and Installation

Installation of the SCT016T-D is designed to be straightforward due to its split-core design, allowing for placement without disconnecting the primary conductor.

2.1 Installation Steps

  1. Open the Buckle: Gently press the safety lock buckle to open the transformer's core.
  2. Clip the Wire: Position the primary conductor (the wire carrying the current to be measured) within the opening of the transformer.
  3. Fasten the Buckle: Close the transformer, ensuring the safety lock buckle clicks securely into place.
  4. Connect Cables: Connect the secondary output terminals to your measurement or monitoring device using appropriate cables. Refer to the wiring diagram for correct polarity.
Safety Latch (180° Opening) of the current transformer
Figure 2: Safety Latch for 180° opening.
Screw terminal output and built-in rectifier of the current transformer
Figure 3: Screw terminal output for secure cable connection.

2.2 Wiring Diagram

The schematic diagram below illustrates the voltage output type and connection points. Ensure the secondary is NOT short-circuited.

Detailed technical data sheet including schematic diagram for wiring
Figure 4: Technical Data Sheet with Schematic Diagram and Electrical Parameters.

2.3 Visual Installation Guide

For a visual demonstration of the installation process, please watch the following video:

Video 1: YHDC SCT016T-D Split Core Current Transformer Installation Guide.

3. Operating Instructions

Once installed and wired correctly, the SCT016T-D will provide a DC voltage output proportional to the AC current flowing through the primary conductor. This voltage signal can then be read by a compatible measurement device, such as a multimeter, data logger, or PLC.

3.1 Measurement Principle

The split core current transformer operates on the principle of electromagnetic induction. The AC current in the primary conductor creates a magnetic field, which is concentrated by the ferrite core. This magnetic field induces a current in the secondary winding, which is then converted into a proportional DC voltage output by the built-in rectifier circuit.

3.2 Output Interpretation

The output voltage (1V, 3V, or 5V DC) corresponds to the maximum rated input current (30A, 50A, 60A, 80A, or 100A) for the specific model. For example, if you have a 100A/5V DC model, a 5V output indicates 100A flowing through the primary conductor. Lower currents will result in proportionally lower voltage outputs.

Important Safety Note: The secondary circuit of the current transformer must NEVER be short-circuited. Doing so can lead to dangerous high voltages and damage the device.

4. Maintenance

The YHDC SCT016T-D is designed for long-term, reliable operation with minimal maintenance. Follow these guidelines to ensure optimal performance and longevity:

  • Cleaning: Keep the exterior of the current transformer clean and free from dust, dirt, and moisture. Use a soft, dry cloth for cleaning. Avoid using abrasive cleaners or solvents.
  • Inspection: Periodically inspect the device for any signs of physical damage, such as cracks in the housing or damage to the safety lock buckle. Ensure the screw terminals are tight and connections are secure.
  • Environmental Conditions: While the device has an IP00 waterproof grade, it is recommended to avoid exposing it to excessive moisture, corrosive environments, or extreme temperatures outside its specified operating range.
  • No User-Serviceable Parts: The internal components of the current transformer are not user-serviceable. Do not attempt to open or repair the device, as this will void the warranty and may cause damage or injury.

5. Troubleshooting

If you encounter issues with your SCT016T-D current transformer, consider the following troubleshooting steps:

  • No Output or Incorrect Readings:
    • Verify that the primary conductor is correctly positioned within the transformer's core and that the safety lock buckle is fully closed.
    • Check all wiring connections to ensure they are secure and correctly match the schematic diagram (Figure 4).
    • Confirm that the secondary circuit is NOT short-circuited. This is a critical safety and operational requirement.
    • Ensure the input AC current is within the rated range of your specific SCT016T-D model.
    • Verify that your measurement device is properly configured to read DC voltage and is compatible with the transformer's output range (1V, 3V, or 5V).
  • Intermittent Readings:
    • Check for loose connections at the screw terminals or within your measurement setup.
    • Ensure the primary conductor is stable and not moving within the transformer's core.
  • Physical Damage:
    • If the housing is cracked, the buckle is broken, or there is any other visible damage, discontinue use immediately. Contact support for assistance.

6. Specifications

The following table details the technical specifications for the YHDC SCT016T-D Split Core Current Transformer:

FeatureSpecification
Model NumberSCT016T-D
Coil StructureSplit core current transformer
Coil NumberCurrent transformer
PhaseSINGLE
Input Current Range30A, 50A, 60A, 80A, 100A
Output Voltage Options1V, 3V, 5V DC
Accuracy1%
Mounting TypeFree hanging (In-Line)
Core MaterialFerrite
Housing MaterialFlame-retardant ABS Injection Shell
Operating Temperature-25ºC ~ +60ºC
Storage Temperature-30ºC ~ +90ºC
Frequency Range50Hz-1KHz
Waterproof GradeIP00
Dielectric Strength (Input/Output)AC 800V/1min 50Hz
Dielectric Strength (Output/Housing)AC 3.5KV/1min 50Hz
Weight70g
CertificationCE

6.1 Dimensions

Dimensions are provided in millimeters (mm) with a tolerance of ±0.5mm.

Front and side view dimensions of the current transformer
Figure 5: Front and Side View Dimensions.

7. Warranty and Support

YHDC is committed to providing high-quality products and excellent customer service.

  • Warranty: The SCT016T-D Split Core Current Transformer comes with a 1-year warranty from the date of purchase, covering manufacturing defects.
  • Technical Support: Should you encounter any issues or require technical assistance during the use of your product, please contact our support team. We aim to provide timely replies within 24 hours and offer comprehensive technical support.
  • Contact Information: For support, please refer to the seller's contact information or visit the official YHDC website at www.poweruc.com.

8. User Tips

  • Proper Sizing: Always ensure the selected current transformer's input current range (e.g., 30A, 50A, 100A) matches or exceeds your application's maximum expected current to maintain accuracy and prevent saturation.
  • Secure Installation: After clipping the primary wire, double-check that the safety lock buckle is fully closed and secured. A loose connection can lead to inaccurate readings or potential hazards.
  • Avoid Secondary Short Circuits: As a critical safety measure, never short-circuit the secondary output terminals. This can generate dangerously high voltages and permanently damage the transformer or connected equipment.
  • Environmental Considerations: Although robust, the device is rated IP00. For outdoor or harsh industrial environments, consider additional protective enclosures to shield it from excessive moisture, dust, and extreme temperatures.
  • Calibration: For highly precise applications, periodic calibration of your entire measurement system (including the current transformer and reading device) is recommended to ensure continued accuracy.

© 2024 YHDC. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.