1. Important Safety Instructions
Please read and follow all instructions carefully to ensure safe and optimal operation of your FULODE X1-6C Audio Mixer.
- Read and save all instructions.
- Heed all warnings.
- Do not use equipment in water or wet areas.
- Clean the equipment with a dry cloth only.
- Do not block any ventilation openings; install according to instructions.
- Do not install near heat sources.
- For safety, do not mix the ground line with the fire line and the zero line. The ground line ensures your safety.
- Avoid trampling on the power supply; place the power cord in a location where it will not be squeezed.
- Only use accessories and wiring provided by the original factory.
- Only use the truck, chassis, and pallet provided or suggested by the original manufacturer to transport the equipment. When using a cart, be careful to prevent tipping over.
- Unplug the mixer during thunderstorms or when not in use for long periods.
- The warranty does not cover damage from broken power cords/plugs, liquid corrosion, hard object impact, rain/wet environments, or improper use.
- The mixer requires a direct connection to the main power supply, which must include a ground wire.
- The mixer is equipped with an AC main power switch on the rear panel.
- This device complies with Class A or Class B radio interference standards.
- Exposure to high noise environments can cause permanent hearing damage. Control sound volume carefully.
Warning Symbols
CAUTION: Risk of electric shock. Do not open.
High voltage icon: Indicates that the chassis has a high voltage. Do not open the chassis without permission.
Special attention to the illustration: Note this point with special attention. If the instructions are not followed, the equipment may be damaged.
Warning: To reduce the risk of fire or electric shock, do not open this device to rain or leave it in a humid environment.
Typical Noise Exposure Levels
| Daily Duration (Hours) | Volume dBA (Slow Response) | Typical Example |
|---|---|---|
| 8 | 90 | Small club ensemble |
| 6 | 92 | |
| 4 | 95 | Subway train |
| 3 | 97 | |
| 2 | 100 | Very loud classical music |
| 1.5 | 102 | |
| 1 | 105 | |
| 0.5 | 110 | |
| 0.25 or less | 115 | The loud part of a rock concert |
2. Product Overview
The FULODE X1-6C is a professional 6-channel audio mixer designed for a variety of applications including recording, karaoke, PA systems, drum mixing, and live music performances. It features 99 built-in DSP effects, USB and Bluetooth connectivity for versatile audio input and playback, and 48V phantom power for condenser microphones.

Figure 2.1: FULODE X1-6C Professional Audio Mixer
Video 2.1: FULODE X1-6C Audio Mixer Features Overview
3. Setup and Connections
3.1 Power Connection
- Locate the DC INPUT port on the rear panel of the mixer.
- Connect the provided power adapter to the DC INPUT port.
- Plug the power adapter into a suitable AC power outlet (AC100-220V~50/60Hz).
- Press the POWER button on the front panel to turn on the mixer. The power indicator will light up.

Figure 3.1: Power Input and Product Dimensions
3.2 Input Connections (MIC/LINE Channels)
The mixer features 6 MIC/LINE input channels, each supporting both XLR and PHONE type plugs for microphones, musical instruments, or external audio devices.

Figure 3.2: Input Panel Overview
- Condenser Microphones: Connect a condenser microphone to an XLR input. Press the +48V PHANTOM button for the corresponding channel to supply 48V phantom power. The LED will light up.
- Wired Microphones/Instruments: Connect wired microphones or instruments using XLR or 6.3mm (PHONE type) connectors to the MIC/LINE inputs.
- PAD Button: For acoustic guitars or other instruments with high output, engage the PAD button to attenuate the signal by 20dB and preserve the original tone.
3.3 USB/Flash Reader/MP3 Connection
The mixer's USB interface allows for PC recording, playing music from a computer, or playing music directly from a USB flash drive (U-disk).
- To play music from a USB flash drive, insert the drive into the USB port. Use the playback controls (previous, play/pause, next) on the mixer's digital display section.
- To connect to a laptop via USB cable for PC recording or playback, use a USB cable to connect the mixer's USB port to your computer.

Figure 3.3: USB/Flash Reader/MP3 Connectivity
3.4 Bluetooth Connection
The mixer supports wireless Bluetooth pairing for music playback from your smartphone or other Bluetooth-enabled devices.
- Activate Bluetooth on your device (e.g., smartphone).
- On your device, search for available Bluetooth devices and select "X1-06" (or similar, as indicated on the mixer's display).
- Once paired, you can play music from your device through the mixer. Use the mixer's playback controls for track navigation and volume adjustment.

Figure 3.4: Bluetooth Pairing
3.5 Output Connections
The mixer provides various output options for connecting to speakers, amplifiers, or recording devices.

Figure 3.5: Output Panel Overview
- MAIN OUT: Connect to active speakers, power amplifiers, or other main sound systems.
- REC OUT (Lotus socket): For recording output.
- PHONES: Connect 2.5mm headphones for monitoring. Adjust the PHONE volume knob for headphone output level.
- AUX OUT: Auxiliary output connectors.
4. Operating Instructions
4.1 Input Channel Controls
Each input channel (1-6) features the following controls:
- MIC/LINE Input Interface: Used for connecting microphones, musical instruments, or external audio devices. Supports both XLR and PHONE type plugs.
- Channel Attenuation Switch (PAD): Press this switch to attenuate the channel signal by 20dB if the input signal is too strong.
- Phantom Power Switch (+48V): When pressed, the LED lights up, supplying +48V phantom power to the XLR plug for condenser microphones.
- Gain Adjustment Knob: Adjusts the basic volume input level for the channel.
- Channel High Frequency Adjustment Knob (HIGH): Controls a +/-15dB increase or decrease of the channel's high band at 12kHz.
- Channel Bass Adjustment Knob (LOW): Controls a +/-15dB increase or decrease of the channel's low band at 80Hz.
- Effect Sending Knob (FX): Adjusts the amount of channel signal sent to the effect bus.
- PAN Sound Balance Knob: Controls the sound and image balance of the left and right channels in stereo.
- Channel Volume Knob (LEVEL): Adjusts the volume of the bus bar that accesses the sound mixing console.

Figure 4.1: Detailed View of Input Channel Controls
4.2 DSP Effects
The mixer includes 99 preset reverb effects to enhance your audio. Use the FX PROGRAM knob to select the desired effect. The digital display will show the effect number.

Figure 4.2: DSP Effects Selection
4.3 Main Output and Monitoring
- MAIN Faders: Control the overall output volume of the left and right main channels. The mixer features damped faders for smooth and precise control.
- PHONE Volume Knob: Adjusts the volume for the headphone monitoring system.
- Level Indicators: Monitor the audio levels to prevent clipping and ensure optimal sound quality.
5. Specifications
| Feature | Specification |
|---|---|
| Model Number | X1-6C |
| Type | Mixers |
| Channels | 6-Channel |
| DSP Effects | 99 Preset Reverb Effects |
| Phantom Power | 48V (selectable per channel) |
| Connectivity | USB, Bluetooth |
| Input Interface | XLR, 6.3mm (PHONE type), USB, Bluetooth |
| Output Interface | MAIN OUT, REC OUT (Lotus), PHONES (2.5mm), AUX OUT |
| Power Input | AC100-220V~50/60Hz |
| Power Output | DC12V:500mA |
| Dimensions (L x W x H) | 31.2 cm (12.28 in) x 23 cm (9.05 in) x 8 cm (3.14 in) |
| Weight | 2.26 kg |
| Origin | Mainland China |
6. Troubleshooting
- No Power: Ensure the power adapter is securely connected to both the mixer and a working power outlet. Check the power button.
- No Sound Output: Verify all cables are correctly connected to the main output and speakers/amplifiers. Check main fader levels and individual channel volume knobs. Ensure the correct input source is selected (USB, Bluetooth, or analog channels).
- Distorted Sound: Check input gain levels for each channel to avoid clipping (indicated by the CLIP LED). If the input signal is too strong, engage the PAD button. Ensure output levels are not too high.
- No Microphone Sound: For condenser microphones, ensure 48V phantom power is activated for the connected channel. Check microphone cable connections.
- Bluetooth Connection Issues: Ensure Bluetooth is enabled on your device and the mixer is in pairing mode. Try restarting both the mixer and your device.
- USB Playback Issues: Ensure the USB flash drive is formatted correctly and contains compatible audio files. Try a different USB drive if problems persist.
7. User Tips
- Gain Staging: Always set your gain levels carefully. Start with the gain knob low, gradually increase it until the signal is strong but not clipping (the CLIP LED should not light up frequently).
- Effect Experimentation: With 99 DSP effects, take time to experiment with different reverb settings to find the perfect ambiance for your vocals or instruments.
- Monitoring: Use the headphone monitoring system to listen to your mix closely without affecting the main output, especially during live performances or recording.
- PAD Button for Clarity: Don't hesitate to use the PAD button for instruments with high output, like some active guitars or keyboards, to prevent input overload and maintain sound clarity.
8. Warranty and Support
For detailed warranty information and customer support, please refer to the official product documentation or contact your retailer. A comprehensive user manual in PDF format is available for download, which may contain additional information regarding specific features and advanced settings. You can find this document by searching for 'FULODE X1-6C User Manual PDF' online or by visiting the manufacturer's support page.