PINTUDY Electric Impact Drill

Contents

Electric Impact Drill User Manual

Model: Electric Impact Drill

1. Introduction

Thank you for choosing the PINTUDY Electric Impact Drill. This versatile cordless tool is designed for various tasks including impact drilling, flat drilling, and screwdriving. It features 25+3 torque settings, a 2-speed control, and an ergonomic design for comfortable and efficient operation. Please read this manual carefully before using the tool to ensure safe and optimal performance.

2. Safety Instructions

WARNING: Always remove the battery pack before changing or removing accessories. Only use accessories specifically recommended for this tool. Others may be hazardous.

WARNING: To reduce the risk of injury, wear safety goggles or glasses with side shields when operating this tool.

Work Area Safety

  • Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.
  • Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite dust or fumes.
  • Keep bystanders, children, and visitors away while operating power tools. Distractions can cause you to lose control.

Personal Safety

  • Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use the tool while tired or under the influence of drugs, alcohol, or medication.
  • Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts.
  • Avoid accidental starting. Ensure the switch is in the locked or off position before inserting the battery pack.

Electrical Safety

  • A battery-operated tool with integral batteries or a separate battery pack must be recharged only with the specified charger for the battery.
  • Only use specifically designated battery packs with the tool. Using any other batteries may create a risk of fire.

Tool Use and Care

  • Use clamps or other practical ways to secure and support the workpiece to a stable platform.
  • Do not force the tool. Use the correct tool for your application.
  • Do not use the tool if the switch does not turn it on or off. A tool that cannot be controlled with the switch is dangerous and must be repaired.
  • Disconnect the battery pack from the tool or place the switch in the off position before making any adjustments, changing accessories, or storing the tool.
  • Store idle tools away from children and other untrained persons.
  • Maintain tools carefully. Keep cutting tools sharp and clean.

3. Package Contents

Please check the package contents upon arrival. The specific items included depend on the purchased set:

Without Battery Set:

  • 1 x Electric Drill
  • 24 x Accessories (various drill bits, screwdriver bits, sockets, flexible shaft)
  • 1 x Plastic Storage Box
  • 1 x Charger (US plug)

1 Battery Set:

  • 1 x Electric Drill
  • 24 x Accessories (various drill bits, screwdriver bits, sockets, flexible shaft)
  • 1 x Plastic Storage Box
  • 1 x Battery (21V, 1.5Ah)
  • 1 x Charger (US plug)
Package contents for the Electric Impact Drill without battery, showing the drill, 24 accessories, plastic box, and charger.
Figure 3.1: Package contents for the 'Without Battery' set, including the electric drill, 24 accessories, plastic box, and charger.

4. Setup

4.1. Battery Installation and Removal

Always ensure the tool is switched off and the control switch is in the locked position before installing or removing the battery.

  1. To Install: Align the battery pack with the slot in the base of the drill handle and slide it in until it clicks securely into place.
  2. To Remove: Press the release button(s) on the side of the battery pack and slide the battery out of the handle.

4.2. Charging the Battery

If your set includes a battery, ensure it is fully charged before first use.

  1. Connect the charger to a power outlet.
  2. Connect the charger plug to the battery pack.
  3. Observe the charging indicator light on the charger/battery.
Table 4.1: Charging Indicator Light Status
Charge StateGreen LightRed LightIndicator State
Charger Into Power SourceOnOffGreen on, Red off
ChargingOffOnGreen off, Red on
After ChargingOnOffGreen on, Red off
Battery AbnormalFlickeringGreen Red Flick
Battery Temperature Below 0°C or Over 45°COffOffGreen off, Red Flick

4.3. Installing Drill Bits and Accessories

Always remove the battery pack before changing accessories.

  1. Twist the chuck counter-clockwise to open the jaws.
  2. Insert the desired drill bit or accessory into the chuck. Ensure it is seated as far as possible.
  3. Twist the chuck clockwise to tighten the jaws firmly around the bit. Hand-tighten only; do not use tools to tighten the chuck.
  4. The chuck capacity is 0.8-10mm (3/8").

5. Operating Instructions

5.1. Control Switch (Forward/Reverse/Lock)

The control switch is located above the trigger. It has three positions: forward, reverse, and lock. The switch can only be adjusted when the ON/OFF trigger is not pressed. Always allow the motor to come to a complete stop before adjusting the switch.

  • Forward (Clockwise Rotation): Push the control switch to the left (when viewed from the rear of the drill).
  • Reverse (Counter-clockwise Rotation): Push the control switch to the right.
  • Lock (Center Position): Push the control switch to the center position. The trigger will not work when locked. This position also serves as a safety lock.
Diagram showing the forward, static (lock), and reverse positions of the drill's control switch.
Figure 5.1: Forward/Reverse Button and Automatic Transmission.

5.2. Starting, Stopping, and Speed Control

  1. To Start: Pull the trigger. An LED light will turn on when the trigger is pulled.
  2. To Vary Speed: Increase or decrease pressure on the trigger. The further the trigger is pulled, the greater the speed. This tool features stepless speed regulation.
  3. To Stop: Release the trigger. The electric brake stops the tool instantly.

5.3. Torque Settings

The drill offers 25+3 torque settings, allowing precise control for various materials and tasks. Rotate the torque collar (ring behind the chuck) to select the desired setting.

  • Settings 1-25 are for screwdriving, with higher numbers providing more torque.
  • The drill icon setting is for drilling applications.
  • The hammer icon setting is for impact drilling into masonry.
Close-up of the drill's torque setting dial, showing numbers from 1 to 25 and drill/hammer icons.
Figure 5.2: Precision Control with 25+3 Torque Settings.

5.4. Speed Gear Selection

The drill has a 2-speed gearbox for optimal performance in different applications.

  • Low Speed (0-550 RPM): For high torque applications like driving screws or drilling large holes.
  • High Speed (0-1550 RPM): For fast drilling in wood, metal, or plastic.

Use the speed selector switch located on top of the drill to choose between high and low speed.

Image showing the drill's speed settings (0-550RPM, 0-1550RPM), chuck capacity (0.8-10mm), and level gauge.
Figure 5.3: High and Low Speed Settings, Chuck Capacity, and Level Gauge.

5.5. Functional Modes

This tool offers three primary functions:

  1. Impact Drilling Mode (Hammer Icon): For drilling into concrete, cement blocks, and red brick walls.
  2. Flat Drilling Mode (Drill Icon): For drilling into ceramic tiles, wood, and metal.
  3. Screwdriver Mode (Screwdriver Icon): For electric equipment overhaul, toy overhaul, and furniture assembly.
Diagram illustrating the three functional modes: impact drilling, flat drilling, and screwdriver mode, with examples of their uses.
Figure 5.4: Three Functional Modes of the Drill.

5.6. Screwdriving Operation

  1. Select the appropriate screwdriver bit and install it securely.
  2. Set the torque collar to a suitable screwdriving setting (1-25).
  3. Place the point of the driver bit in the screw head and apply firm, steady pressure to the tool.
  4. Start the tool slowly and then increase the speed gradually. Release the trigger as soon as the clutch cuts in (if using a torque setting).

CAUTION: Make sure the driver bit is inserted straight in the screw head, or the screw and/or bit may be damaged.

5.7. Drilling Operation

First, turn the adjusting ring so that the pointer points to the appropriate drilling mark (drill icon for flat drilling, hammer icon for impact drilling).

Drilling in Wood

When drilling in wood, the best results are obtained with wood drills equipped with a guide screw. The guide screw makes drilling easier by pulling the bit into the workpiece.

Drilling in Metal

To prevent the bit from slipping when starting a hole, make an indentation with a center-punch and hammer at the point to be drilled. Use a cutting lubricant when drilling metals (except iron and brass, which should be drilled dry).

Drilling in Stone/Masonry

Use appropriate masonry drill bits. Add water during the drilling process to prevent overheating and extend bit life.

CAUTION: Pressing excessively on the tool will not speed up drilling. This can damage the bit, decrease tool performance, and shorten its service life.

5.8. Impacting Techniques (for Screwdriving)

The longer a bolt, screw, or nut is impacted, the tighter it will become. To help prevent damaging fasteners or workpieces, avoid excessive impacting. Practice with various fasteners to determine the required impacting time for desired torque. If fasteners are too tight, reduce impacting time; if not tight enough, increase impacting time.

5.9. Additional Features

  • LED Work Light: A built-in LED light illuminates dark work areas for better visibility.
  • Level Gauge: The integrated level gauge helps ensure that your work is accurate and straight.
  • Ergonomic Non-Slip Grip: Designed for comfortable handling and reduced fatigue during extended use.

6. Maintenance

Always remove the battery pack before performing any maintenance or cleaning.

6.1. Cleaning

  • Keep the tool's ventilation openings clean and free from dust and debris to prevent overheating.
  • Wipe the tool's exterior with a soft, damp cloth. Do not use harsh chemicals or abrasive cleaners.
  • Keep the chuck jaws clean to ensure proper grip on bits.

6.2. Tool and Accessory Care

  • Maintain tools carefully. Keep cutting tools sharp and clean. Properly maintained tools with sharp cutting edges are less likely to deviate and are easier to control.
  • Store the tool and accessories in a dry, secure place, away from direct sunlight and extreme temperatures.

6.3. Battery Care

  • Do not store batteries in temperatures above 45°C (113°F) or below 0°C (32°F).
  • If the tool is operated continuously until the battery cartridge has discharged, allow the tool to rest for 15 minutes before proceeding with a fresh battery.

7. Troubleshooting

Table 7.1: Troubleshooting Guide
ProblemPossible CauseSolution
Tool does not startBattery not installed correctly or discharged; Control switch in lock position; Faulty trigger.Ensure battery is fully charged and properly seated; Move control switch to forward or reverse; Contact support if trigger is faulty.
Reduced power or speedBattery is low; Incorrect speed setting for task; Overload.Recharge battery; Select appropriate speed gear (low for high torque); Reduce pressure on tool.
Tool overheatsContinuous heavy use; Blocked ventilation slots.Allow tool to cool down; Clear any obstructions from ventilation slots.
Drill bit slips in chuckChuck not tightened sufficiently; Bit shank is dirty or damaged.Ensure chuck is tightened firmly; Clean or replace bit.

8. Specifications

Table 8.1: Product Specifications
FeatureSpecification
ColorBlue
Maximum Output Power500W
Maximum Output Torque38NM
Speed (Low)0-550 RPM
Speed (High)0-1550 RPM
Chuck Capacity0.8-10mm (3/8")
Speed Gear2 gears (High and Low)
Switch TypeStepless Speed Switch
Vibration Level (Brick Wall)8.0 m/s²
Vibration Level (Drill Metal)2.5 m/s² or less
Sound Pressure Level82 dB(A)
Functions3 (Impact Drill, Electric Hammer Drill, Screwdriver)
Material Thickness (Steel)10mm
Material Thickness (Wood)30mm
Material Thickness (Concrete)10mm
Battery Voltage21V
Battery Capacity1.5Ah
Detailed specifications of the electric drill, including power, torque, speed, chuck capacity, and material thickness capabilities.
Figure 8.1: Detailed Product Specifications.

9. User Tips

No specific user tips were available from the provided buyer reviews or Q&A content.

10. Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the seller's terms and conditions or contact the manufacturer directly. Keep your proof of purchase for any warranty claims.

11. Product Video Overview

Watch this video for a visual overview of the Electric Impact Drill's features and capabilities.

Video 11.1: Product demonstration of the Electric Impact Drill.

© 2023 PINTUDY. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.