Introduction
This staniot WSR100 Wireless Outdoor Alarm Siren with Strobe Light is designed for enhanced home security. It operates wirelessly, powered by a rechargeable solar battery, and can function as a standalone siren or integrate with an existing alarm system. When triggered, it emits a high-decibel sound and flashes a warning light to deter intruders. Its waterproof design ensures reliable operation in various outdoor conditions.

Specifications
| Feature | Specification |
|---|---|
| Built-in Battery | DC 3.7V (3.7V/1000mAh) rechargeable lithium battery |
| External Power Supply | DC 6~12V |
| Max Output | 5V/150mA |
| Standby Time (without sunlight) | 60 days |
| Standby Current | <500uA |
| Alarm Current | ≤350mA |
| Wireless Frequency | 433MHZ (1527 code / 330K) |
| RX Sensitivity | -113dBm |
| Wired Defense Zones | 2 (Z0, Z1) |
| Wireless Zones | 50 |
| Alarm Volume | 120dB |
| Working Temperature | -10°C ~ +50°C |
| Relative Humidity | <95% (no condensation) |
| Size | 265mm*190mm*60mm |

Setup
Physical Installation
The siren is designed for wall-mounted installation. Choose a location that receives adequate sunlight for optimal solar charging and is visible to deter potential intruders. Ensure the mounting surface is stable and secure.


Pairing with Alarm Panel
To integrate the siren with your alarm panel:
- Press and hold the SET button on the siren for 2 seconds until it beeps once and the warning light stays on. This indicates the siren is in sniffer mode.
- On your alarm panel, navigate to the accessory pairing menu and select 'Siren' or 'Add Accessory'.
- Trigger the pairing function on the alarm panel (e.g., press the SOS button if available, or follow specific panel instructions).
- A long beep from the siren and a quick flash of the warning light confirm successful pairing. If you hear three short beeps and the warning light flashes 3 times, it means the siren has been successfully paired.
- If no operation occurs for more than 20 seconds, the siren will automatically exit sniffer mode.
Pairing with Wireless Accessories
The process for pairing with wireless accessories (e.g., door/window sensors, PIR sensors, remote controls) is similar to pairing with the alarm panel:
- Press and hold the SET button on the siren for 2 seconds until it beeps once and the warning light stays on (sniffer mode).
- Trigger the wireless accessory (e.g., press a button on the remote control, trigger a sensor).
- A long beep from the siren and a quick flash of the warning light confirm successful pairing. If you hear three short beeps and the warning light flashes 3 times, it means the accessory has been paired.
- If no operation occurs for more than 20 seconds, the siren will automatically exit sniffer mode.
Wired Defense Zones (Z0, Z1)
The siren features two wired defense zones (Z0 and Z1) for connecting wired detectors. These zones support normally open (NO) wired detection and are active when the system is armed. When a wired detector connected to Z0 or Z1 triggers an alarm, the siren will sound and flash.

Operation
Arming, Home Arming, Disarming, and SOS with Remote Control
You can use a remote control (if paired) to quickly manage your alarm system:
| Button | What you hear | What you see | What happens |
|---|---|---|---|
| Arm | Short beep once | Warning light quickly flashes once (and the siren will flash once per 1min) | The alarm sounds when a door or window opens, or when there's motion in a room. |
| Home Arm | Short beep once | Quickly flashes once (and the siren will flash once per 1min) | The alarm sounds when a door or window opens. |
| Disarm | Short beep twice | Quickly flashes twice | The alarm won't sound. |
| SOS | Alarm sound | Quickly flashes continuously | Immediate alarm activation. |
Siren Alarm Tone Setting
The siren offers different alarm sound frequencies and durations. To adjust, refer to the 'Alarm tone setting' jumpers on the PCB diagram (see Specifications section):
- Default: 600~1500Hz for 0.333~0.385s.
- Option 1: 800Hz & 1000Hz for 1.67~2.5s.
- Option 2: 600~1500Hz for 3~5s.
- Option 3: Same as default.
Alarm Sound Delay Time Setting
The siren allows for adjustable alarm sound delay times. To adjust, refer to the 'Delay time setting' jumpers on the PCB diagram (see Specifications section):
- Default: Delayed by 1 minute (factory default).
- Option 1: Delayed by 3 minutes.
- Option 2: Delayed by 5 minutes.
Maintenance
Solar Charging
The siren is equipped with a solar panel for continuous charging of its built-in lithium battery. Ensure the solar panel is exposed to direct sunlight for optimal performance. In conditions without sufficient sunlight, the battery provides approximately 60 days of standby time.

Battery
The siren has a built-in 3.7V/1000mAh rechargeable lithium battery. Regular exposure to sunlight helps maintain battery charge. If the siren is installed in a shaded area, periodic manual charging or ensuring an external power supply (DC 6-12V) might be necessary to prevent battery depletion.

Troubleshooting
- Siren not sounding/flashing:
- Check if the siren is properly paired with the alarm panel or accessories. Re-pair if necessary.
- Ensure the siren's battery is charged (check solar panel exposure or external power).
- Verify the alarm system is armed.
- Check wired defense zones for proper connection and if they are normally open.
- Siren not pairing:
- Ensure the siren is in sniffer mode (single beep, warning light on).
- Confirm the alarm panel/accessory is sending the pairing signal correctly.
- Check for interference from other wireless devices.
- Try resetting the siren by deleting all wireless accessories and re-pairing.
- False alarms:
- Check sensitivity settings of connected sensors.
- Ensure wired defense zones are correctly configured and not accidentally triggered.
User Tips
- Optimal Placement: For best solar charging, install the siren in a location that receives direct sunlight for several hours a day. This ensures the built-in battery remains charged.
- System Integration: While the siren can work standalone, integrating it with a full alarm system (e.g., Tuya platform) provides comprehensive security features and remote control capabilities.
- Regular Testing: Periodically test the siren's functionality, especially after any power outages or system changes, to ensure it's operating correctly.
Warranty and Support
For detailed information, including warranty terms and advanced troubleshooting, please refer to the official user manual PDF available at: Wireless Outdoor Alarm Siren User Manual (PDF).
For further assistance, contact staniot Official Store support.