Fosi Audio CA30

Contents

Fosi Audio CA30 Car HiFi Amplifier User Manual

Model: CA30

1. Introduction

Thank you for purchasing the CA30 car audio power amplifier. The CA30 is a high-performance car amplifier manufactured by Fosi Audio, designed for 12V automotive systems to deliver HiFi sound reproduction and amplification. With the latest Infineon's automotive-grade Class D amplifier chips, it features a compact heatsink design (186x101x44.2mm), high power output (4x100W@4Ω/4x160W@2Ω), High fidelity (full-range & flat frequency response 10Hz~40KHz), exceptional efficiency (over 88%). It is specifically engineered for audiophiles seeking premium sound quality in automotive entertainment systems.

The CA30 features high-pass/low-pass/full-pass filters, enabling flexible configuration as a high-frequency, low-frequency, or full-range speaker system. Its crossover frequencies can be precisely adjusted according to users' preferences. It also supports RCA low-level/high-level inputs (High input with sensing DC offset and auto turn-on function), compatible with most original car head unit systems equipped with RCA line outputs or high-level outputs. Whether you're a car audio enthusiast or audiophile, the CA30 will take you on an extraordinary journey of HiFi music.

Fosi Audio is committed to delivering premium in-vehicle audio solutions, ensuring every user enjoys exceptional sound quality.

2. Product Overview & Controls

The Fosi Audio CA30 amplifier features a compact design with clearly labeled controls and terminals for easy setup and operation.

Fosi Audio CA30 Amplifier Panel Overview
Figure 2.1: Top and Bottom Panel Overview of the CA30 Amplifier

Control Descriptions:

  1. Crossover Frequency Control (FREQ CH1/2, FREQ CH3/4): This control sets the crossover frequency for the respective channels when either High-Pass Filter (HPF) or Low-Pass Filter (LPF) is selected. The frequency is adjustable between 50Hz and 250Hz.
  2. Crossover Mode Select Switch (X-OVER CH1/2, X-OVER CH3/4): This switch selects the crossover mode:
    • FULL: For full-range output.
    • HPF: Limits low-frequency information passed to speakers.
    • LPF: Limits high-frequency information passed to speakers.
  3. Gain Control (GAIN CH1/2, GAIN CH3/4): Used to match the input signal level from the source unit to the amplifier. Adjust to prevent clipping.
  4. Power/Protection/Clipping Indicators (CLIP PWR PRT):
    • PWR (Blue): Lights up when the amplifier is on.
    • PRT (Red): Lights up in case of critical operation or protection mode.
    • CLIP (Orange): Lights up when distortion reaches 1%, indicating gain should be reduced.
  5. Line Input (CH1, CH2, CH3, CH4): RCA jacks for low-level signal input (CH1/2 or CH1/2/3/4 channels). Connect to the source unit using RCA audio cables.
  6. High Level Input: For connection to the speaker output of your source (head unit) if it lacks low-level outputs. Supports automatic power on/off with DC offset sensing.
  7. Power Terminals (GND, REM, +12V): Used to connect DC power to the amplifier. GND for ground, REM for remote turn-on, +12V for battery positive.
  8. Speaker Terminals (CH1, CH2, CH3, CH4, BRIDGED): Used to connect speaker cables to the amplifier. Supports both stereo and bridged configurations.

3. Specifications

The following table details the technical specifications of the Fosi Audio CA30 Car HiFi Amplifier:

Feature Specification
Amplifier ChipInfineon IR4322
Op-ampsJRC NJM4580E/ ST TJM4558CDT
RMS Power @ 4Ω100W x 4
RMS Power @ 2Ω160W x 4
Bridge Power @ 4Ω320W x 2
Frequency Response10Hz-40kHz
Low Pass Frequency Crossover50Hz-250Hz
High Pass Frequency Crossover50Hz-250Hz
Power/Protection IndicatorBlue / Red
Clipping Indicator LightOrange
Damping Coefficient (100Hz @ 10W)≥140
Input Sensitivity0.75-8V
Interference @ 1kHz≥60dB
Signal Noise Ratio (SNR)>100dB
SINAD≥80dB
Remaining Noise≤200μV
T.H.D +@5W≤ 0.008%
Fuse30A x 2 (Internal)
Dimension (LxWxH)186 x 101 x 44.2 mm (7.3 x 3.9 x 1.7 in)

4. Package Contents

Please check the box for the following items:

  • Fosi Audio CA30 Amplifier x 1
  • User Manual x 1
  • Screws
  • 30A Fuse x 2
  • 8-pin Ribbon Cable x 1
  • Wrenches x 2
Fosi Audio CA30 Package Contents
Figure 4.1: Contents of the CA30 Product Package

5. Setup & Installation

Proper installation is crucial for optimal performance and safety. Please follow these guidelines carefully.

5.1 Power Connections

Fosi Audio CA30 Power Connection Diagram
Figure 5.1: Power Connection Diagram
  1. +12V Battery Connection: Connect a power wire to the vehicle's positive battery terminal. This connection must be tight and secure. Install a 60A external fuse on the power cable within 50 cm (12 to 16 inches) of the vehicle battery. Connect the power wire to the +12V terminal of the amplifier using an Allen screw driver. Do not install the fuse until installation is complete. Recommended cross section: minimum AWG 10.
  2. Ground Connection: Make the ground connection to the vehicle's chassis, keeping it as short as possible. Choose a solid piece of sheet metal. Sand the contact point to remove rust, paint, or grime. Connect the ground wire to the GND terminal of the amplifier with an Allen screw driver. Recommended cross section: minimum AWG 10.
  3. Power-on REM Control Line: The Power-on REM control line is typically controlled by the source unit's remote turn-on output. The amplifier turns on when +12V is present at its remote (REM) input and turns off when +12V is switched off. Connect the remote wire (12 to 16 gauge) to the REM connection of the amplifier. Connect the other end to the source unit's turn-on output or ignition switch circuit.
    Note: When using a high-level input with DC offset sensing for auto turn-on, the REM connection is not required.

5.2 Audio Input Connections

RCA Low Level Input

The RCA jacks allow for low-level signal input for CH1/2 or CH1/2/3/4 channels. Connect to your source unit using RCA type audio cables. Keep these cables away from power wiring to reduce noise.

Fosi Audio CA30 RCA Low Level Connection Diagram
Figure 5.2: RCA Low Level Input Connection

High Level Input

Use the high-level input for connection to the speaker output of your source (head unit) if it does not have a low-level output. Do not connect high-level input and RCA low-level input simultaneously.

5.3 Speaker/Subwoofer Wiring

Connect your speakers and/or subwoofers to the amplifier's speaker terminals. Ensure correct polarity for all connections to prevent short circuits or damage.

Fosi Audio CA30 Speaker and Subwoofer Wiring Diagram
Figure 5.3: Speaker and Subwoofer Wiring Diagram
  • Multiple speakers can be connected in parallel to a single channel.
  • In stereo mode, the total impedance per channel must not be lower than 2 Ω.
  • In bridged mode, the total impedance must not be lower than 4 Ω.
  • Use properly rated cables. Power and ground cables should be AWG #4, and the REM wire should be AWG #16 to #18.

5.4 General Installation Notes

  • For optimal cooling, install the amplifier with the cooling fins facing upward. Maintain 5–10 cm of clearance around the amplifier and do not cover the fins during operation.
  • Compatible with gasoline vehicles with a supply voltage of 10–16V.

6. Operating the Amplifier

Once installed, the CA30 amplifier is ready for operation. Adjust the settings according to your audio system and preferences.

  • Power On/Off: The amplifier will turn on automatically when a remote signal (+12V) is received via the REM terminal or when a DC offset is detected on the high-level input. It will turn off when these signals are removed.
  • Gain Adjustment: Use the GAIN controls for CH1/2 and CH3/4 to match the output level of your source unit. Start with the gain at minimum and slowly increase until the desired volume is reached without distortion. If the CLIP indicator lights orange, reduce the gain.
  • Crossover Settings: Use the X-OVER switches and FREQ controls for CH1/2 and CH3/4 to configure your speaker system. Select FULL for full-range, HPF for high-pass, or LPF for low-pass, then adjust the frequency as needed (50Hz-250Hz).
Video 6.1: Fosi Audio CA30 Product Overview and Features

7. Maintenance

To ensure the longevity and optimal performance of your Fosi Audio CA30 amplifier, consider the following maintenance tips:

  • Cleaning: Regularly clean the exterior of the amplifier with a soft, dry cloth. Avoid using harsh chemicals or abrasive cleaners.
  • Ventilation: Ensure that the cooling fins are free from dust and debris. Proper airflow is essential to prevent overheating.
  • Connections: Periodically check all power and speaker connections to ensure they remain tight and secure. Loose connections can lead to poor performance or damage.
  • Environment: Avoid exposing the amplifier to extreme temperatures, moisture, or direct sunlight.

8. Troubleshooting

If you encounter issues with your CA30 amplifier, refer to the following common problems and solutions:

  • No Power / Amplifier Not Turning On:
    • Check the +12V power connection and ensure the fuse is intact.
    • Verify the ground connection is secure.
    • Ensure the REM wire is properly connected and receiving +12V from the source unit.
    • If using high-level input, confirm the source unit is on and providing a DC offset signal.
    • Check if the blue PWR indicator light is on.
  • No Sound / Low Output:
    • Check all audio input (RCA or high-level) and speaker connections for proper seating and polarity.
    • Ensure the source unit is playing audio and its volume is up.
    • Adjust the GAIN controls on the amplifier.
    • Verify the crossover settings (FULL, HPF, LPF) are appropriate for your speakers.
  • Distorted Sound / Clipping:
    • Reduce the GAIN control on the amplifier.
    • Check if the orange CLIP indicator light is on; if so, reduce gain until it turns off.
    • Ensure speaker impedance meets the amplifier's requirements (min 2Ω stereo, min 4Ω bridged).
  • Amplifier Goes into Protection Mode (Red PRT Indicator):
    • Check for short circuits in speaker wiring.
    • Ensure proper ventilation to prevent overheating.
    • Verify speaker impedance is within acceptable limits.
    • Check for over-/under-voltage or reverse polarity in power connections.

9. User Tips

  • The Fosi Audio CA30 is praised for its great sound quality, high signal-to-noise ratio, and excellent efficiency. Its compact size allows for versatile installation options, even in tight spaces.
  • Many users confirm the amplifier delivers a true 4x100W RMS output, making it a powerful choice for car audio enthusiasts.
  • To prevent potential issues, always double-check all wiring connections, especially power and ground, and ensure the correct fuse is installed as specified in the manual.

10. Warranty & Support

Fosi Audio pledges a 12-month limited warranty and support from the date of purchase. If you encounter any problems when using your product, please contact our support team.

For detailed information, you can refer to the official user manual PDF: CA30 User Manual (PDF)

Contact Information:

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.