1. Introduction
The LCTC DZ108-20 Motor Protection Circuit Breaker is designed to provide essential protection for small capacity motors and electrical circuits against overload and short circuit conditions. It can also function as a direct starter for motors and as a switch for circuit changeover under normal operating conditions. This manual provides detailed instructions for safe installation, operation, and maintenance of the device.
2. Safety Information
WARNING: Electrical shock hazard. Installation and maintenance should only be performed by qualified personnel.
- Always disconnect power before installing, servicing, or removing the circuit breaker.
- Ensure all wiring complies with local and national electrical codes.
- Do not operate the device if it appears damaged or malfunctioning.
- Verify correct voltage and current ratings before connection.
- Wear appropriate personal protective equipment (PPE) when working with electrical systems.
3. Product Overview
The DZ108-20 is a compact moulded case circuit breaker featuring button control for operation and an adjustable current setting for precise protection. It is designed for easy installation on a 35mm DIN rail.
4. Specifications
The following table details the technical specifications for the LCTC DZ108-20 Motor Protection Circuit Breaker:
| Attribute | Value |
|---|---|
| Product Name | Motor Circuit Breaker |
| Model | DZ108-20 |
| Type | Moulded Case Circuit Breaker |
| Pole | 3 Pole |
| Contact Type | 1NO 1NC |
| Current Setting Range | 0.16-32A (Specific models vary, e.g., 1A-20A, 4-6.3A, 24-32A) |
| Max Rated Voltage | 660V AC |
| Rated Insulation Voltage | 660V |
| Rated Frequency | 50/60Hz |
| Power of Controlled Motor | Up to 7.5KW |
| Thermal Overload Release Setting Current | 14-20A (for specific variants) |
| Momentary Overload Release Setting Current | 240A |
| Operation Type | Button control |
| Installation | 35mm DIN rail installation |
| Certification | CE |
| EU LVD Voltage | Below 50Vac or 75Vdc |
5. Installation
The DZ108-20 circuit breaker is designed for quick and secure installation on a standard 35mm DIN rail.
- Mounting: Align the circuit breaker's installation clamp plate with the 35mm DIN rail. Press firmly until it clicks into place, ensuring it is securely fastened.
- Wiring: Connect the power supply and motor leads to the designated terminals (1L1, 3L2, 5L3 for input; 2T1, 4T2, 6T3 for output). Ensure all connections are firm and wires do not fall off. Refer to the product labeling for specific terminal assignments.
- Auxiliary Contacts: If using the 1NO 1NC auxiliary contacts, connect them to your control circuit as required (e.g., for status indication or interlocking).
6. Operating Instructions
- Current Adjustment: Before energizing the circuit, set the desired operating current using the adjustable dial on the front of the circuit breaker. This setting should match the full load current of the motor or protected circuit.
- Power On: Press the 'ON' button (typically grey or green) to close the circuit and supply power to the motor.
- Power Off: Press the 'OFF' button (typically red) to open the circuit and cut off power.
- Protection Activation: In case of an overload or short circuit, the breaker will trip automatically, opening the circuit to protect the equipment.
- Resetting: After a trip, identify and rectify the cause of the fault. Once the fault is cleared, reset the circuit breaker by pressing the 'OFF' button first (if it's not already in the tripped position), then press the 'ON' button to re-energize the circuit.
7. Maintenance
- Regularly inspect the circuit breaker for any signs of physical damage, discoloration, or loose connections.
- Ensure the terminals are clean and free from dust or corrosion.
- Periodically test the trip mechanism if your installation allows for safe testing procedures.
- Keep the area around the circuit breaker clear of obstructions to allow for proper ventilation and access.
8. Troubleshooting
- Breaker trips frequently:
- This usually indicates an overload or a short circuit. Check the motor or connected load for faults, excessive current draw, or wiring issues. Ensure the current setting on the breaker is appropriate for the load.
- Breaker does not reset:
- If the breaker does not reset after a trip, there might still be a fault in the circuit, or the breaker itself could be damaged. Disconnect power, inspect the circuit and the breaker. If the fault persists, consult a qualified electrician.
- Motor does not start:
- Check if the circuit breaker is in the 'ON' position. Verify power supply and motor connections. Ensure the current setting is not too low, causing an immediate trip upon motor start-up.
9. User Tips
- Always select a circuit breaker with a current rating appropriate for your motor or load to ensure effective protection without nuisance tripping.
- For optimal performance, ensure the installation environment is within the recommended temperature and humidity ranges for electrical equipment.
- Consider labeling your circuit breaker to clearly identify the circuit it protects.
10. Frequently Asked Questions (FAQ)
- Q: What is the primary function of this circuit breaker?
- A: Its primary function is to protect motors and circuits from damage due to overload and short circuit conditions.
- Q: Can this breaker be used as a main switch?
- A: Yes, it can be used as a direct starter for motors and as a switch for circuit changeover under normal conditions.
- Q: How do I adjust the current setting?
- A: The current is adjusted via a dial on the front of the unit. Ensure power is off before making adjustments.
11. Product Video
Watch this video for a visual demonstration of the LCTC DZ108-20 Motor Protection Circuit Breaker:
12. Warranty and Support
For warranty information and technical support, please refer to the official LCTC website or contact your authorized dealer. Keep your purchase receipt for warranty claims.
A detailed user manual in PDF format is available for download: View User Manual (PDF)