eletechsup SD29AJTC

Contents

SD29AJTC MPPT Solar Charging Board

User Instruction Manual

Model: SD29AJTC

1. Safety & Warnings

Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.

  • Warning: Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Do not expose to water or moisture. This is an electrical product.
  • Handle with care to avoid cuts or injuries.

2. Product Overview

The SD29AJTC is a versatile MPPT (Maximum Power Point Tracking) solar charging board and DC-DC step-down battery charger. It is designed to efficiently charge various multi-cell lithium batteries from a solar panel input.

Key Features:

  • Photovoltaic Cell Maximum Power Point Tracking (MPPT)
  • Supports Single or Multi-cell Lithium-ion, LiFePO4, or Lithium Titanate Batteries
  • Can be used as a Voltage Source when Battery is Absent
  • Charging Current is programmable with a current sense resistor (1A/2A/4A options)
  • Battery Overvoltage Protection
  • Automatic Conditioning of Deeply Discharged Batteries
  • Automatic Recharge

Component Identification:

Refer to the image below for key components and their functions.

SD29AJTC Board Layout with Labels
Figure 2.1: SD29AJTC Board Layout. Shows VIN/GND input, BAT+/BAT- output, MPPT and VOUT adjustment potentiometers, and the J1 jumper.
  • VIN / GND: DC input terminals for solar panel (DC 7-28V).
  • BAT+ / BAT-: DC output terminals for battery charging (1.2-25V adjustable).
  • MPPT ADJ Potentiometer: Adjusts the Maximum Power Point Tracking voltage.
  • VOUT ADJ Potentiometer: Adjusts the output charging voltage.
  • J1 Jumper: Shorting this jumper disables the MPPT function.
  • CR LED: Charge status indicator.

3. Specifications

Parameter Value
Input Voltage DC 7-28V
MPPT Voltage DC 7-25V (Adjustable)
Output Voltage 1.2-25V (Adjustable)
Charging Current Options 1A / 2A / 4A (Configurable via RCS resistors)
MPPT Disable Solder J1 Pad
Operating Ambient Temperature -40℃ to +85℃
Dimensions (L x W x H) 59 x 30 x 15mm
Weight 16g (no Terminal); 19g (with Terminal)
Output Type SINGLE
Type DC/DC Converters
Certification NONE

Charging Current Configuration (RCS Resistors):

The maximum charging current is determined by the parallel connection value of the two resistors RCS1 and RCS2. The formula is ICH = 120mV / Rcs.

RCS Resistor Table for Charging Current
Figure 3.1: RCS Resistor Values vs. Charging Current. This table shows the resistor values required for different charging currents.

4. Setup & Installation

4.1. Wiring Connections:

Connect your solar panel to the VIN and GND terminals. Connect your battery to the BAT+ and BAT- terminals. Ensure correct polarity.

Wiring Diagrams for Various Battery Types
Figure 4.1: Wiring Diagrams. Examples for connecting to LiFePO4 and Lithium batteries with corresponding charging voltages.

4.2. Parameter Adjustment (Example: 18V Solar Panel, Charge 12.8V LiFePO4 Battery):

  1. Connect a 100-200Ω resistor to the BAT+/BAT- terminals.
  2. Connect the solar panel output to the VIN/GND terminals.
  3. Use a multimeter to measure the voltage at the BAT+/BAT- port.
  4. MPPT Voltage Adjustment:
    • If there is no voltage output at BAT+/BAT-, turn the MPPT ADJ potentiometer clockwise until voltage output appears.
    • If there is voltage output, rotate the MPPT ADJ potentiometer counter-clockwise until there is just voltage output (this sets the MPPT point).
  5. Output Voltage Adjustment: Rotate the VOUT ADJ potentiometer to set the output voltage to 12.8V (or your desired battery charging voltage).

4.3. Disabling MPPT:

To disable the MPPT function, short the J1 jumper pad on the board.

5. Operating Instructions

5.1. Charging Process:

  • The 'CR' LED indicates the charge status.
  • It is normal for the device to still be charging even after the 'CR' LED goes out.

5.2. Important Operating Notes:

  • This is a buck (step-down) module. The input voltage must be at least 3V greater than the desired output voltage.
  • If the output fails after connecting to the power supply, verify that the MPPT voltage is not set too high and reduce it if necessary.
  • The output current (charging current) is determined by the capacity and power requirements of the connected battery. The maximum current cannot be directly output without a battery connected.

6. Maintenance

  • Keep the device in a dry environment and protect it from dust and moisture.
  • Before each use, visually inspect the board for any signs of damage, such as burnt components, loose connections, or physical cracks. Do not use if damaged.
  • Ensure proper ventilation around the module during operation, especially when charging at higher currents.

7. Troubleshooting

Problem Possible Cause / Solution
No output after connecting power. MPPT voltage may be set too high. Reduce the MPPT voltage using the MPPT ADJ potentiometer. Ensure input voltage is at least 3V higher than desired output.
CR charging indicator is off, but battery is still charging. This is normal behavior. The LED indicates a primary charging phase.
Module does not output maximum current. The output current is determined by the connected battery's capacity and power requirements. The module will not output maximum current without a proper load.
Module not functioning. Verify that the input voltage is at least 3V higher than the set output voltage. Check all wiring for correct polarity and secure connections.

8. User Tips

  • Always use a multimeter to verify voltages before connecting sensitive components or batteries.
  • Start with the MPPT and VOUT potentiometers at their minimum settings and slowly adjust upwards to avoid overvoltage.
  • When adjusting potentiometers, make small turns and allow a few seconds for the voltage to stabilize before taking a reading.
  • For optimal performance, ensure your solar panel's voltage range falls within the module's input and MPPT voltage specifications.

9. Warranty & Support

Manufacturer: Guangzhou Keshen Electronic Technology Co., Ltd

Address: CN-Room 301, No.8-1 Beixin Street, Kemulang Aotou, Tianhe District, Guangzhou City, China

Email: eletechsup@163.com

Specific warranty details for this product are not provided in the available documentation. Please contact the seller or manufacturer directly for warranty information and technical support.

For additional information, you may refer to the official user manual PDF: View User Manual (PDF)

10. Product Video

Video 10.1: Product Overview. A short clip demonstrating the physical size and appearance of the SD29AJTC charging board.

© 2024 eletechsup. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.