COOLMOON 240

Contents

COOLMOON 240MM Water Cooling CPU Cooler

User Instruction Manual

Introduction

This manual provides detailed instructions for the installation, operation, maintenance, and troubleshooting of your COOLMOON 240MM Water Cooling CPU Cooler. This AIO (All-In-One) liquid cooling system is designed to provide efficient heat dissipation for your CPU, featuring double PWM ARGB fans and an efficient PWM controlled pump. It is compatible with various AMD sockets, including AM4 and AM5.

For additional details and diagrams, please refer to the official User Manual (PDF).

Setup and Installation

Follow these steps for proper installation of your CPU liquid cooler:

  1. Prepare your Motherboard: Ensure your motherboard is compatible with AMD/AM4/AM5 sockets.
  2. Mount the Radiator: Install the 240MM radiator in an appropriate location within your PC case, typically at the top or front, ensuring adequate airflow.
  3. Install the Fans: Attach the two PWM ARGB fans to the radiator. Ensure the fan cables are routed correctly.
  4. Apply Thermal Paste: Apply a thin, even layer of thermal paste to the CPU's IHS (Integrated Heat Spreader).
  5. Mount the Pump/Cold Plate: Carefully place the pump/cold plate assembly onto the CPU, aligning it with the mounting holes. Secure it with the appropriate mounting hardware for your CPU socket.
  6. Connect Power and ARGB Cables:
    • Connect the pump's 5v-3pin ARGB interface cable to the corresponding 5V3-pin ARGB header on your motherboard.
    • Connect the fan's 5v-3pin ARGB interface cables to the motherboard's ARGB headers or a dedicated ARGB controller.
    • Connect the fan's 4-pin PWM power cables to the CPU_FAN or SYS_FAN headers on your motherboard.
PC case with ARGB liquid cooler installed, showing connection to 5V3-pin interface on motherboard
Figure 1: Example installation showing ARGB lighting and connection to the 5V3-pin interface on the motherboard.

The water pipe length is approximately 380mm ±10%, providing sufficient reach for most computer cases.

Operation

Temperature Control (PWM)

The cooler supports PWM (Pulse Width Modulation) for efficient temperature control, energy saving, and noise reduction:

  • When the CPU temperature rises, the motherboard's PWM mode automatically increases the fan speed (800~2000RPM±10%) to cool down the CPU.
  • When the CPU temperature drops, the fan speed is automatically reduced, contributing to energy efficiency and quieter operation.
Diagram illustrating PWM temperature control with fan speed range
Figure 2: PWM interface and fan speed control mechanism.

Addressable ARGB Lighting

The cooler features addressable 5V ARGB lighting, offering programmable 16 million colors. The water pump is also equipped with ARGB lamp beads that synchronize with the fans.

Compatibility includes motherboards with 5V ARGB functions such as ASUS Aura Sync, MSI Mystic Light Sync, Gigabyte RGB Fusion 2.0, and ASRock Polychrome Sync. You can control the lighting effects through your motherboard's software.

Close-up of the pump with ARGB lighting and 5V 3PIN interface
Figure 3: The pump features ARGB lighting and connects via a 5V 3PIN interface.

Maintenance

The COOLMOON liquid cooler is designed for low maintenance. Key features contributing to its durability and performance include:

  • Sealed & Leak-Proof Design: The water-cooling pipe interface utilizes industrial-grade sealing technology, providing resistance to stretching, bending, and ensuring a leak-free operation.
  • Durable Polymer Material Tube: The FEP (Fluorinated Ethylene Propylene) water-cooled pipe offers excellent tensile resistance, bending resistance, and sealing performance. It features a braided network tube, which is more durable than traditional rubber tubes, providing 4 layers of protection:
    1. Black braided net
    2. Rubber layer
    3. White fiber mesh
    4. Rubber layer
Diagram of the polymer FEP water-cooled pipe structure with 4 layers of protection
Figure 4: Cross-section of the polymer FEP water-cooled pipe, highlighting its four protective layers.

Regularly check for dust accumulation on the radiator fins and fans. Use compressed air to clean them as needed to maintain optimal cooling performance.

Troubleshooting

If you encounter issues with your COOLMOON liquid cooler, consider the following:

  • No Power/Fans Not Spinning:
    • Ensure all power cables (4-pin PWM for fans, pump power) are securely connected to the motherboard.
    • Check your motherboard's BIOS/UEFI settings to ensure fan headers are enabled and configured correctly.
  • No ARGB Lighting/Incorrect Colors:
    • Verify that the 5v-3pin ARGB cables are correctly connected to the motherboard's 5V ARGB header (not 12V RGB).
    • Check your motherboard's ARGB control software (e.g., ASUS Aura Sync, MSI Mystic Light Sync) for proper configuration.
    • Ensure the software is up-to-date.
  • High CPU Temperatures:
    • Confirm the pump is running (you might feel a slight vibration or hear a faint hum).
    • Ensure the cold plate is making good contact with the CPU and that thermal paste was applied correctly.
    • Check for any obstructions to airflow around the radiator.
    • Verify fan orientation for proper airflow (intake or exhaust).
  • Unusual Noise:
    • Check if fan blades are hitting any cables or obstructions.
    • Ensure all mounting screws are tightened properly to prevent vibrations.

Specifications

Feature Specification
Model Number 240
Radiator Type 240 MM
Fan Interface 5v-3pin ARGB
Pump Interface 5v-3pin ARGB
With Liquid Yes
RGB Support A-RGB
Type AIO Liquid Cooling Accessories
Origin Mainland China
Fan Airflow 65 CFM ±10% (MAX)
Fan Speed 800~2000RPM ±10%
Pipe Length 380mm ±10%
Heat Exchange Channels 14 E-shaped fins
Estimated Lifespan 60,000 hours
Package Length 38 cm
Package Width 23 cm
Package Height 15 cm
Package Weight 1.7 kg
Exploded view diagram of the pump components
Figure 5: Exploded view of the pump, detailing its internal components for efficient heat dissipation.

User Tips

  • Software Configuration: After physical installation, ensure you install and configure your motherboard's ARGB control software to customize lighting effects and fan curves for optimal performance and aesthetics.
  • Cable Management: Proper cable management not only improves the aesthetics of your build but also ensures unobstructed airflow, which is crucial for cooling efficiency.
  • Regular Cleaning: Periodically clean the radiator fins and fan blades to prevent dust buildup, which can hinder heat dissipation.

Warranty and Support

For any technical support or warranty inquiries, please refer to the seller's contact information or the official product page where you purchased the item. The product is designed for a long lifespan, estimated at 60,000 hours.

For comprehensive instructions and diagrams, please download the full User Manual (PDF).

© 2024 COOLMOON. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.