Introduction
Thank you for choosing the Edieu T-03 Professional Electric Hair Clipper & Beard Trimmer. This manual provides essential information for the safe and effective use, maintenance, and care of your new grooming device. Please read it thoroughly before first use and keep it for future reference.
Important Safety Information
WARNING: To reduce the risk of burns, electrocution, fire, or injury to persons:
- Fire Risks: Strictly follow the instructions for charging and storage.
- Electric Shock Hazard: This product is NOT washable. Do not immerse this product in water or wash it under a tap. Improper operation may result in short circuits, fires, electric shocks, personal injury, or even death.
- Child Safety: This product is not suitable for unattended use by children. Keep out of reach of children.
- Sharp Blade: Be careful when cleaning or replacing the blade to avoid cuts.
- Battery Safety: Use only the original charger. Do not disassemble or throw the battery into fire.
- Usage Restrictions: Do not use on eyes, mucous membranes, or other sensitive areas. Do not use on areas with skin damage or inflammation.
- This product is for personal care use only and must not be used for industrial or animal trimming.
For disposal information, especially regarding lithium-ion batteries, please visit your local government website for guidelines on safe disposal.
Complies with EU health, safety, environmental requirements and RoHS directive.
Package Contents
Your Edieu T-03 Hair Clipper & Trimmer set typically includes the following items:
- 1x Professional Hair Clipper (T-03 model)
- 1x T-Blade Trimmer (T-02 model, if included in set)
- Multiple Guide Combs (various sizes, e.g., 1.5mm, 3mm, 4.5mm, 6mm, 10mm, 13mm, 16mm, 19mm, 22mm, 25mm)
- 2x USB Charging Cables
- 1x Cleaning Brush
- 1x Lubricating Oil (small amount)
- 1x Barber Cape (may vary by package)
- 1x Hair Comb (may vary by package)
- 2x Scissors (may vary by package)
Setup
1. Initial Charging
Before first use, ensure the battery is fully charged. Connect the clipper to the original charger using the provided USB cable. The LED display will show the "POWER LEFT" percentage and charging mode. A full charge typically takes approximately 3 hours.
2. Attaching Guide Combs
Select the desired guide comb for your preferred cutting length. Align the comb with the clipper blade and push it firmly until it clicks into place. Ensure it is securely attached before use.
Operating Instructions
1. Power On/Off
Press the power button to turn the clipper on or off. The LED display will illuminate when the device is active.
2. General Hair Cutting
- Ensure the hair is clean and dry for best results. This product is NOT washable and should not be immersed in water.
- Maintain a proper angle between the blade and skin during use, avoiding excessive pressure.
- Move the clipper against the direction of hair growth for an even cut.
- The clipper can be used wired (connected to power) or wirelessly (on battery power).
3. Taper Level Adjustment (Main Clipper)
The main hair clipper features 5 taper level lengths, adjustable via a lever on the side. This allows for fine-tuning of cutting length between guide comb sizes, typically ranging from 0.7mm to 1.6mm.
4. T-Blade Trimmer Use (for T-02 model/set)
The T-blade trimmer is ideal for zero-gap trimming, detailing sideburns, shaping beard lines, and creating precise hair lines. It also serves as a perfect tool for hair fading. The cutting tools can be adjusted for very short hair, ranging from 0.45mm to 0.8mm, allowing for slight adjustments to leave short hair or achieve a bald look.
Cleaning and Maintenance
- After Each Use: Turn off the power. Clean the blade head with the provided small brush to remove any trapped hair.
- Blade Washing: While the main unit is not washable, the blades can be detached and rinsed under water for cleaning. Ensure blades are completely dry before reattaching or storing.
- Lubrication: Apply a small amount of lubricant (oil) periodically to the blade head to ensure smooth operation and prolong blade life. The LED display may show a lubricating reminder icon.
- Storage: Store the clipper in a dry place.
- Avoid Chemicals: Do not use thinner, benzene-based solvents, or alcohol to wipe the hair clipper or charger, as this may cause discoloration.
- Avoid Corrosives: Do not use corrosive cleaning agents.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Clipper does not turn on. | Battery is depleted. | Charge the clipper for approximately 3 hours using the original charger. |
| Clipper pulls hair or cuts unevenly. | Blades are dull, dirty, or not lubricated. Incorrect technique. | Clean blades thoroughly. Apply lubricating oil. Ensure proper angle and avoid excessive pressure. |
| Clipper becomes warm during use/charging. | Normal operation. | This is normal. Continue use with confidence. If excessively hot, discontinue use and contact support. |
| LED display shows lubrication reminder. | Blades require lubrication. | Apply a small amount of lubricating oil to the blades. |
Specifications
| Feature | Detail |
|---|---|
| Brand Name | Edieu |
| Model | T-03 (T-02/T-03 Series) |
| Item Type | Hair Trimmer / Hair Clipper |
| Power Type | Mains and Battery Operation (Corded/Cordless) |
| Motor Type | Vibratory |
| Blade Material | Stainless Steel |
| Battery Capacity | 2500mAh |
| Battery Charging Time | Approx. 3 Hours |
| Battery Life (Usage Time) | Approx. 180 Minutes |
| Voltage | <20V |
| Functions | Dry haircut, Washing blades under water (not entire unit), Fast Charging, Charging indication |
| Minimum Cutting Length | 0.45mm - 1mm (with taper adjustment) |
| Maximum Cutting Length | Up to 25mm (with guide combs) |
| Length Adjustment Method | Change of nozzles (guide combs), Taper lever |
| Number of Nozzles (Guide Combs) | 5 or more (up to 10-12 depending on set) |
| Purpose | For the head (hair, beard, sideburns) |
| Certifications | CE, CCC, 3C, RoHS |
| High-concerned chemical | None |
| Noise Reduction | Yes (Quiet operation) |
*Note: Specifications may vary slightly depending on the specific package or model variant (e.g., T-02 vs. T-03).
User Tips
- For a smoother cut, ensure hair is detangled before trimming.
- Always start with a longer guide comb than you think you need, and gradually reduce the length if desired.
- Regularly check the LED display for battery level and lubrication reminders to ensure optimal performance.
- When trimming beards or detailing, use the T-blade trimmer for precise lines and edges.
- Clean the blades immediately after each use to prevent hair buildup and maintain hygiene.
Warranty and Support
For warranty claims, technical support, or service inquiries, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.
For additional information or to view the original user manual (PDF), please refer to the following link: